GENMASK is used to create a contiguous bitmask([hi:lo]).
This patch is a copy from Linux, with below commit details
"bitops: Fix shift overflow in GENMASK macros"
(sha1: 00b4d9a14125f1e51874def2b9de6092e007412d)
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since it's a copy from Linux, this patch moved all
BIT definitions to top so-that it looks same as Linux file.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This driver did not yet configure the SDHCI MBUS bridge registers.
Without this and with CONFIG_MMC_SDMA enabled, mmc hangs at random
times. As DMA cannot complete correctly.
Tested on db-88f6820-gp eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dirk Eibach <eibach@gdsys.cc>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
This patch enables DM_SERIAL for all ARCH_MVEBU boards (AXP & A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables DM_USB on the Marvell AXP / A38x eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds driver model (DM) support to the Marvell EHCI driver.
This will be used by the MVEBU SoC's, currently Armada XP and 38x.
Tested on Marvell Armada XP and 38x eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds driver model support for some Marvell MVEBU SoC's. Including
Armada XP and 38x. All 3 currently mainlined boards are converted. DM is now
selected automatically for MVEBU platforms.
With this DM support now available for MVEBU, hardcoding the base addresses
and other information is not necessary any more. Probing should be done
by using the values provided via the device tree now instead. For this
the driver also need to be converted to DM. Patches for some of the drivers
will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
These will be needed by the upcoming DM (driver model) support for
the Armada XP / 38x SoC's. This will provide DT based probing.
The dts files are copied 1:1 from the Linux kernel release v4.2.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the MVEBU SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The current "simple" address translation simple_bus_translate() is not
working on some platforms (e.g. MVEBU). As here more complex "ranges"
properties are used in many nodes (multiple tuples etc). This patch
enables the optional use of the common fdt_translate_address() function
which handles this translation correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the use of the kwboot tool, to boot mainline U-Boot
on the Marvell Armada XP/38x SoC's. This is done by returning to the
SoC's BootROM after SPL has initialized the SDRAM. We need to make sure
to not reconfigure the internal register space and MBARs. Otherwise
the BootROM will not be able to continue after SPL jumps back to it.
To use this feature, please don't forget to change the BOOT_FROM line
in your board specfic kwbimage.cfg file this way:
BOOT_FROM uart
Tested on these Marvell eval boards:
DB-MV784MP-GP - Armada XP
DB-88F6820-GP - Armada 38x
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
The DT is identical to the DT submitted to the upstream kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Linux had a number of changes to the AXP209 DTSI. Sync ours.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add the latest kernel changes to the sun5i family DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
So far, even if CONFIG_MMC was not enabled the board code was trying to use
the MMC-related functions, resulting in linker errors.
Protect those calls by an ifdef.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a generic Kconfig option for the CONFIG_MMC option that was used before
in the configuration headers.
Since all the architectures need to be converted to that first, depend on
an non-existent config option that will be extended with architectures that
use that option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The current fastboot support assumes that CONFIG_FASTBOOT_FLASH implies
that we have an MMC in our system, which might not be the case if we have
some other storage device.
Change the configuration option protecting that call to
FASTBOOT_FLASH_MMC_DEV, that makes much more sense.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When using the fastboot boot command, the image sent to U-Boot will be an
Android boot image. If the support is missing, that obviously won't work,
so we need it in our configuration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used
for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet
phy. ALDO1 is used to power the sdio wifi module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a bootcmd_sunxi_compat value to the default environment when building
with CONFIG_OLD_SUNXI_KERNEL_COMPAT, this way people who occasionally want
to boot an old kernel can do so by simply typing "run bootcmd_sunxi_compat"
rather then needing to have 2 separate setups / sdcards for old and
new kernels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
ELDO3 is only necessary when using the lcd-panel, and not when using hdmi,
the display code already takes care of enabling ELDO3 when necessary,
so there is no need to permanently enable it in the deconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
LDO3 and LDO4 are normally either unused, or used to power csi
attached camera sensors, and as such do not need to be enabled at
boot time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for disabling the regulators found on the axp209 pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The only thing axp221.c's axp_init() does which needs protection
against multiple calls is calling pmic_bus_init, and pmic_bus_init()
itself is already protected against being called multiple times.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use the generic pmic_bus helpers for the axp152 / axp209 drivers,
rather then having them define their own register read / write
functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V, make this
the default.
Note that this does not cause any functional changes since all sun8i
board defconfig-s already contained: CONFIG_AXP_ALDO1_VOLT=3000 .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change the axp223 dcdc2 / VDD-SYS default from 1.2V to 1.1V, 1.1V is the
value recommended by Allwinner and is what most fex files specify.
This has been tested on a number of A23/A33 tablets including on an
A23 Ippo-q8h-v1.2 PCB tablet which has a fex file which specifies 1.2V
(which is where our original 1.2V default comes from).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.
The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Kconfig-ify CONFIG_AXP152_POWER and _AXP209_POWER settings, removing
them from CONFIG_SYS_EXTRA_OPTIONS.
Note that sun5i boards can have either an AXP209 or an AXP152 pmic, the
Kconfig default is AXP209, boards with an AXP152 must explicitly select
this. Likewise boards without a pmic must explicitly select SUNXI_NO_PMIC
in their defconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have generic q8_a?3_defconfig files for Q8 formfactor tablets with
an A13 / A23 / A33 SoC, there is no need for these PCB variant specific
defconfig-s and they only serve to confuse the user.
Note that in case of the forfun_q88db_defconfig and TZX-Q8-713B7_defconfig
for A13 based Q8 tablets there is not even a dts file for these in the
upstream kernel, which is all the more reason to remove them.
The generic q8_a?3_defconfig files have been tested on an Et_q8_v1_6,
Ippo_q8h_v1_2_a33_1024x600, Ippo_q8h_v1_2 and TZX-Q8-713B7 tablet, and the
forfun_q88db_defconfig is identical to q8_a13_tablet_defconfig.
This leaves only the Ippo_q8h_v5 untested with the new generic defconfigs
but there is no reason to assume that it will not work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more
room on the stack once we've the DRAM running.
Besides being a good change to have on itself, this also paves the
way for switching to using malloc_simple in the SPL which cuts of
close to 4KiB of the SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
malloc_simple uses a part of the stack as heap, initially it uses
SYS_MALLOC_F_LEN bytes which typically is quite small as the initial
stacks sits in SRAM and we do not have that much SRAM to work with.
When DRAM becomes available we may switch the stack from SRAM to DRAM
to give use more room. This commit adds support for also switching to
a new bigger malloc_simple heap located in the new stack.
Note that this requires spl_init to be called before spl_relocate_stack_gd
which in practice means that spl_init must be called from board_init_f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
common/dlmalloc.c is quite big, both in .text and .data usage, therefor
on some boards the SPL is build to use only malloc_simple.c and not the
dlmalloc.c code. This is done in various include/configs/foo.h with the
following construct:
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
This commit introduces a SPL_MALLOC_SIMPLE Kconfig bool which allows
selecting this functionality through Kconfig instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
spl_relocate_stack_gd only gets called from arch/arm/lib/crt0.S which
clears the bss directly after calling it, so there is no need to clear
it from spl_relocate_stack_gd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Between v2015.07-rc1 and v2015.07-rc2 this board started
silent boot failure. A bisect led to commit 6eed3786c6
("net: Move the CMD_NET config to defconfigs"). This commit
looks harmless in itself, but it did implicitly add a feature
to the image which led to this:
u-boot$git describe 6eed3786c6
v2015.07-rc1-412-g6eed3786c68c
^^^
u-boot$ls -l ../41*/u-boot.bin
-rwxrwxr-x 1 paul paul 261476 Oct 16 16:47 ../411/u-boot.bin
-rwxrwxr-x 1 paul paul 266392 Oct 16 16:43 ../412/u-boot.bin
u-boot$bc
bc 1.06.95
Copyright 1991-1994, 1997, 1998, 2000, 2004, 2006 Free Software Foundation, Inc.
This is free software with ABSOLUTELY NO WARRANTY.
For details type `warranty'.
256*1024
262144
i.e. we finally broke through the 256k monitor size. Jump it
up to 384k and fix the hard coded value used in the env offset
at the same time.
We were probably flirting with the 256k size issue without
knowing it when testing on different baselines in earlier
commits, but since this is all board specific, a rebase or
reorder to put this commit 1st is of little value.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When debugging an env fail due to too small a malloc pool, it
was noted that the env write was 256k. But the device sector
size is 1/2 that, as can be seen from "fli" output:
Bank # 1: CFI conformant flash (16 x 16) Size: 16 MB in 131 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1888
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 64 bytes
Sector Start Addresses:
FF000000 E RO FF020000 E RO FF040000 E RO FF060000 E RO FF080000 E RO
FF0A0000 E RO FF0C0000 E RO FF0E0000 E RO FF100000 E RO FF120000 E RO
[...]
FFF00000 RO FFF20000 RO FFF40000 RO FFF60000 RO FFF80000 RO
FFFA0000 RO FFFC0000 RO FFFE0000 E RO FFFE8000 RO FFFF0000 E RO
FFFF8000 RO
=>
The desired env sector is FFF40000->FFF60000, or 0x20000 in length,
just after the 256k u-boot image which starts @ FFF00000.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently the board fails to save its env, since the env size
is much smaller than the sector size, and the malloc fails for
the pad buffer, giving the user visible symptom of:
Unable to save the rest of sector (253952)
Allow for 1M malloc pool, the same as used on the sbc8548 board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Jagan Teki
Tom Rini
Stefan Roese
Maxime Ripard
Hans de Goede
Simon Glass
Paul Gortmaker