Add support for the onboard eSDHC MMC controller. The hardware on the
MPC8308RDB has the following errata:
- ESDHC111: manual asynchronous CMD12 is broken
- DMA is broken (PIO works)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
[added include fsl_esdhc header to prevent implicit declarations of
fsl_esdhc_mmc_init() and fdt_fixup_esdhc()]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The SPI pins are routed to header J8 for testing SPI functionality. A
Spansion flash has been wired up and tested on this header.
This patch breaks support for the second TSEC interface, since the GPIO
pin used as a chip select is pinmuxed with some of the TSEC pins.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This board is the only board that still sticks to OneNAND IPL.
Remove this board, since we have SPL around for a while and
OneNAND is well supported in the SPL framework. The board can
be revived if necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tom Rini <trini@ti.com>
After removing the Apollon board, remove the OneNAND IPL too.
There are no users for it any more.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <promsoft@gmail.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Support for multiple soft I2C buses.
Multibus I2C support is achieved by defining get_multi_{sda|scl}_pin
functions to switch between multiple "soft" I2C buses.
Common definition of I2C_X I2C buses is provided at <i2c.h>.
TEST HW:
Samsung's Exynos4210 evt.0.1 - Trats development board
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch is derived from an older patch provided by atmel in its
buildroot-avr32-v3.0.0.tar.bz2
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Move board specific function to board_init function in board/ folder
Remove externs from generic board.c
Use board_init_f function in board.c file.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Ventana always pulls in files from the Seaboard directory, so needs to
mkdir $(obj)../seaboard unconditionally. This fixes:
git clean -f -d -x
./MAKEALL ventana
"MAKEALL -s tegra20" passes without this change, because Seaboard
happens to be built before Ventana, and hence the directory has already
been created.
I believe the mkdir is only needed for out-of-tree builds, since the
seaboard directory is part of the source tree. However, since we always
build an SPL for Tegra now, which I believe is effectively an out-of-tree
build, we will always need this at some time. The overhead of just
uncondtionally executing the mkdir is minimal, and simplifies the
Makefile, since we don't need to code up the exact minimal condition to
execute the mkdir.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This commit enables NAND support on the Tamonten Evaluation Carrier and
adds the corresponding device tree nodes. Furthermore, the U-Boot
environment can now be stored in NAND.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a flash node to handle the NAND, including memory timings and
page / block size information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In order to use the serial interface on the PortuxG20 we need to enable the
level converter first by setting the PC9 pin to high. The level converter needs
some time to settle so we have to use the mdelay() function to wait for some
time. Unfortunately we have no timers available at board_early_init_f() so we
enable the serial output early within board_postclk_init().
Now the U-Boot output looks fine:
| U-Boot 2012.07-00132-gaf1a3b0-dirty (Aug 16 2012 - 18:21:32)
|
| CPU: AT91SAM9G20
| Crystal frequency: 18.432 MHz
| CPU clock : 396.288 MHz
| Master clock : 132.096 MHz
| DRAM: 64 MiB
| WARNING: Caches not enabled
| NAND: 128 MiB
| In: serial
| Out: serial
| Err: serial
| Net: macb0
| Hit any key to stop autoboot: 0
Signed-off-by: Markus Hubig <mhubig@imko.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Because of the way USB pad settings are handled it doesn't make sense to
be able to build the Efika MX board support without CONFIG_CMD_USB turned
on. So, we change the build to always compile in USB support.
We do not need to check for CONFIG_CMD_USB like we do with CONFIG_MXC_SPI
since the USB subsystem will error out of the compile for us.
Additionally, the following behaviors have changed;
* Smartbook "preboot" should not set input and output to USB keyboard as
there is no display support
* board_eth_init is implemented such that it does not cause U-Boot to
report an explicit failure ("CPU Net Initialization Failed").
Since Ethernet is implemented via USB (fixed on Smarttop, pluggable on
Smartbook, and handled by "usb start") - the warning that is left
("No ethernet found") is perfectly reasonable at the point it is printed
since the USB system hasn't been started and nothing has been probed yet.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Recent conversion from mx28_adjust_memory_params to mxs_adjust_memory_params
missed to update mx28evk, which caused the board not to boot.
Apply the conversion so that the board can boot again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Align the SSP clock speed with oscilator to achieve higher transfer
stability.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
* fix chip select initialization for frame buffer, this will be
increase frame buffer access speed
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch restores the Linkstation's original behaviour when powering off.
Once the (soft) power switch is turned off, linux will reboot and the
bootloader turns off HDD and USB power. Then it loops as long as the switch
is in the off position, before continuing the boot process again.
Additionally, this patch fixes the board function set_led(LED_OFF).
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
For some reasons we had an own implementaion of dram_init and
dram_init_banksize. This is not needed anymore, use the standard
kirkwood functions instead.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
The fanless boards now have a 7-digit (XXXXX-F) board name. This
triggers a border condition when reading this string in the IVM although
this string is smaller than the currenly read string size, but only by 1
character.
This patch corrects this by changing the size check condition for string
length. It is the same change that was done in the platform for this
same bug.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Bigler <stefan.bigler@keymile.com>
* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
tx25: Use generic gpio_* calls
config: Always use GNU ld
tools: add kwboot binary to .gitignore file
fdt: Include arch specific gpio.h instead of asm-generic/gpio.h
serial: CONSOLE macro is not used
Conflicts:
board/karo/tx25/tx25.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
A lot of at91 boards have the console_init_f in board_init. This is useless
cause it was called before by generic code in lib/board.c.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Jens Scharsig <esw@bus-elektronik.de>
cc: Stelian Pop <stelian@popies.net>
cc: Sedji Gaouaou<sedji.gaouaou@atmel.com>
cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
cc: Eric Benard <eric@eukrea.com>
Tested-by: voice.shen@atmel.com
Tested-by: voice.shen@atmel.com
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
fix a bug:
when not boot from NAND, the NAND flash can not be detected.
Using this to fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tom Rini
Albert ARIBAUD
Alison Wang
Ira W. Snyder
Marek Vasut
Fabio Estevam
Łukasz Majewski
Andreas Bießmann
Michal Simek
Tom Warren
Stefano Babic
Ashok Kumar Reddy
Stephen Warren
Thierry Reding
Simon Glass
Markus Hubig
Matt Sealey
Otavio Salvador
Jens Scharsig
Michael Walle
Karl O. Pinc
Holger Brunck
Valentin Longchamp
Wolfgang Denk
Wu, Josh
Bo Shen