Commit graph

4466 commits

Author SHA1 Message Date
Simon Schwarz
5183b7ec48 devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss
This moves CONFIG_SYS_TEXT_BASE one MB after beginning of SD-RAM. Move
CONFIG_SYS_SPL_MALLOC_START to have one MB of free space for the u-boot
image.

CONFIG_SYS_TEXT_BASE was in the middle of the bss-section. This was the
reason for the problems with MMC boot described here:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/118711

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:41 +01:00
Manjunath Hadli
754f8cb689 da850evm: pass board revision info to kernel
there are two boards based on da850 SOC - OMAP-L138 and AM18x.
In order to differentiate between these two boards, revision id
is passed to kernel via second byte of ATAG_REVISION.

Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
2011-12-06 23:59:40 +01:00
Stefano Babic
fda241d59d MX35: flea3: changes due to hardware revision B
Revision B of the board uses CSD0 for the DRAM,
as usual for MX3 boards. The patch fixes also
some values in the U-Boot environment.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-12-06 23:59:40 +01:00
Stefano Babic
40f6fffee5 MX: serial_mxc: cleanup removing nasty #ifdef
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
2011-12-06 23:59:40 +01:00
Tom Rini
ee08a8260a OMAP3: Add SPL_BOARD_INIT hook
Add an SPL_BOARD_INIT hook and for OMAP3 have it turn on i2c.  OMAP4
doesn't need i2c enabled in SPL.  Enable SPL_BOARD_INIT on devkit8000.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Tom Rini
d067cc464f AM3517 CraneBoard: Add SPL support
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE

Cc: Nagendra T S <nagendra@mistralsolutions.com>
Tested-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Tom Rini
5059a2a471 AM3517: Add SPL support
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE

Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Tom Rini
673283f3fc OMAP3: Add SPL support to omap3_evm
Add Hynix 200MHz timing information to <asm/arch-omap3/mem.h>.
This also changes CONFIG_SYS_TEXT_BASE to 0x80100000.

Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
75c57a3570 OMAP3: Add SPL support to Beagleboard
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation.  The memory init
logic is also based on what x-loader does in these cases.  Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC.  We also change CONFIG_SYS_TEXT_BASE to
0x80100000.

Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Tom Rini
9ae0d55074 OMAP3 SPL: Rework memory initalization and devkit8000 support
This changes to making the board be responsible for providing the
memory initialization timings in SPL and converts the devkit8000
to this framework.  In SPL we try and initialize both CS0 and CS1.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:38 +01:00
Heiko Schocher
f7264c36cd arm, davinci: add support for am1808 based enbw_cmc board
- booting from NOR Flash with direct boot method
- POST support
- LOGBUF support

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Christian Riesch <christian.riesch@omicron.at>
2011-12-06 23:59:37 +01:00
Christian Riesch
e8c856d288 arm, hawkboard: Use the pinmux configurations defined in the arch tree
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the hawkboard use these definitions instead of
defining its own.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
2011-12-06 23:59:37 +01:00
Christian Riesch
52b0f877a2 arm, da850evm: Use the pinmux configurations defined in the arch tree
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the da850evm use these definitions instead of
defining its own.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
2011-12-06 23:59:36 +01:00
Koen Kooi
27b8c8f267 BeagleBoard: config: Really switch to ttyO2
The previous commit changed it to "zero two" instead of the proper "Oh two". This was completely broken!

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Acked-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:35 +01:00
Anatolij Gustschin
10e2568d03 ARM: davinci_dm6467Tevm: Fix build breakage
Fix:

arch/arm/cpu/arm926ejs/davinci/libdavinci.o: In function `timer_init':
/work/agust/git/u-boot/arch/arm/cpu/arm926ejs/davinci/timer.c:62:
 undefined reference to `davinci_arm_clk_get'

drivers/i2c/libi2c.o: In function `i2c_init':
/work/agust/git/u-boot/drivers/i2c/davinci_i2c.c:102:
 undefined reference to `davinci_arm_clk_get'

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2011-12-06 23:59:35 +01:00
Thomas Weber
81dcf8bb11 ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
This patch removes the definition of stack sizes for
irq and fiq if the CONFIG_USE_IRQ is undefined before.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2011-12-06 23:59:35 +01:00
Thomas Weber
0997561de9 ARM: OMAP3: Remove unused define SDRC_R_C_B
This patch removes the unused definition of SDRC_R_C_B
from the config files.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Acked-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:35 +01:00
Thomas Weber
8152c6f6f5 ARM: OMAP3: Remove unused define CONFIG_OMAP3430
This patch removes the CONFIG_OMAP3430, because it is unused.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2011-12-06 23:59:35 +01:00
Aneesh V
f6ddfdd3a9 omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
Change the CONFIG_SYS_TEXT_BASE and the addresses of SDRAM
buffers used by SPL(heap and BSS) keeping in mind the
following requirements:

1. Make sure that SPL's heap and BSS doesn't come in the way
of Linux kernel, which is typically loaded at 0x80008000. This
will be important when SPL directly loads kernel.

2. Align the CONFIG_SYS_TEXT_BASE between TI internal
U-Boot and mainline U-Boot. This avoids a lot of confusion
and allows for the inter-operability of x-loader, SPL,
internal U-Boot, mainline U-Boot etc. The internal U-Boot's
address can not be changed to that of mainline U-Boot
as internal U-Boot doesn't have relocation and 0x80100000
used by mainline U-Boot will clash with kernel

3. Assume only a minimum amount of memory that may be available
on any practical OMAP4/5 board in future too. We are assuming
a minimum of 128 MB of memory

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Aneesh V
8e40852f0d omap: fix cache line size for omap3/omap4 boards
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:34 +01:00
Aneesh V
d71a4916d6 omap4: ttyO2 instead of ttyS2 in default bootargs
Set console=ttyO2 instead of ttyS2 in default bootargs
according to latest kernel config

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Marek Vasut
67a1f00c7c PXA: Flip colibri_pxa27x to pxa-common.h
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:33 +01:00
Marek Vasut
cd0f3d2eb8 PXA: Introduce common configuration header for PXA
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:33 +01:00
Marek Vasut
f9f5486c74 PXA: Cleanup Colibri PXA270
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:32 +01:00
Marek Vasut
abc20aba18 PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:32 +01:00
Marek Vasut
3e43c749f2 PXA: Unify vpac270 environment size
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-12-06 23:59:32 +01:00
Marek Vasut
7c7204db35 PXA: Enable command line editing for vpac270
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:32 +01:00
Marek Vasut
411b9eaf55 PXA: Adapt Voipac PXA270 to OneNAND SPL
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

V2: Add missing u-boot-spl.lds, convert bitshifts to division,
    convert to spl_onenand_load_image()
2011-12-06 23:59:32 +01:00
Marek Vasut
00d5ec937d PXA: Fixup PXA25x boards after start.S update
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:32 +01:00
Marek Vasut
c477d72c04 PXA: Drop XM250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
d299173139 PXA: Drop PLEB2 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
00c4acaa97 PXA: Drop CRADLE board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
f13eba66fd PXA: Drop CERF250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Tim Schendekehl
14c3261497 Ethernut 5 board support
Add support for the Ethernut 5 open hardware design, based
on Atmel's AT91SAM9XE512 SoC.

V4
 - Fix several coding style issues.
 - Move machine type to config file.
 - Remove use of CONFIG_ATMEL_LEGACY.

Signed-off-by: Tim Schendekehl <tim.schendekehl@egnite.de>
2011-12-06 23:59:31 +01:00
Simon Guinot
77ea071fef ARM: remove duplicated code for LaCie boards
This patch groups together all the common functions for LaCie boards:
Ethernet PHY and MAC address initializations.

Moreover the configurations for LaCie Kirkwood boards are merged into
a single file: include/configs/lacie_kw.h

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-12-06 23:59:30 +01:00
Simon Guinot
5628fb75d1 ARM: add support for LaCie 2Big Network v2
This patch adds support for the LaCie 2Big Network v2 board, based on
the Marvell Kirkwood 6281 SoC.

Additional information is available at:
http://lacie-nas.org/doku.php?id=2big_network_v2

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-12-06 23:59:30 +01:00
Simon Guinot
0bfb66b6d1 netspace_v2: Read Ethernet MAC address from EEPROM
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-12-06 23:59:30 +01:00
Sanjeev Premi
35e3f6d769 omap3evm: Add support for EFI partitions
Defines CONFIG_EFI_PARTITION for OMAP3 EVM.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <tom.rini@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-12-06 23:59:30 +01:00
Wolfgang Denk
d194837fc3 Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
  Makefile: add tools/mkenvimage to target 'clean'
  mv_common.c: get rid of 'defined but not used' warning
  m68k: fix ambiguous bit testing
  sparc: fix unknown escape sequence warnings
  sparc: fix unused variable warnings
  sf: fix erase debug output
2011-12-05 23:33:48 +01:00
Mike Frysinger
3a2b9f28c0 sparc: fix unknown escape sequence warnings
I don't know what exactly the code was going for, but the object code
is the same before/after my change, and in looking at the env strings,
this seems to be OK.

Otherwise gcc warns:
cc1: warning: unknown escape sequence: '\$'
cc1: warning: unknown escape sequence: '\)'
cc1: warning: unknown escape sequence: '\040'
cc1: warning: unknown escape sequence: '\$'
cc1: warning: unknown escape sequence: '\)'

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-12-05 21:55:24 +01:00
Nobuhiro Iwamatsu
6d1d5cf96e sh: Add support for ecovec board
The ecovec board has SH7724, 256MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
	- 256MB DDR2-SDRAM
	- USB
	- I2C
	- Ethernet

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:22 +09:00
Yoshihiro Shimoda
25a028bbc7 sh: espt: change config for new sh_eth driver
The new sh_eth driver uses the phy driver. So, this patch enables it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:21 +09:00
Yoshihiro Shimoda
c8ceca9514 sh7763rdp: change config for new sh_eth driver
The new sh_eth driver uses the phy driver. So, this patch enables it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:21 +09:00
Nobuhiro Iwamatsu
3ed8164587 sh: Add a flag which controls the DDR ECC mode of sh7757lcr
When DDR-ECC is effective, the physical memory which can be used
reduces this boardby half. However, this mode can chenge to disable.
When it was disabled, user can use 512 MB of physical memory.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: "Yoshihiro Shimoda" <yoshihiro.shimoda.uh@renesas.com>
Acked-by: "Yoshihiro Shimoda" <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:21 +09:00
Yoshihiro Shimoda
0c2a37a5d3 sh7757lcr: change config for new sh_eth driver
The new sh_eth driver uses the phy driver. So, this patch enables it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:20 +09:00
Wolfgang Denk
797449a16d Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
  ppc4xx: Add Io64 board support
  ppc4xx: fix PMC440 painit command
  ppc4xx: remove invalid access to PCI_BRDGOPT2 register
  ppc4xx: use CONFIG_PCI_BOOTDELAY instead of private implementation
2011-12-02 00:03:08 +01:00
Wolfgang Denk
d51e6d6de2 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  mpc85xx: support for Freescale COM Express P2020
  arch/powerpc/cpu/mpc8xxx/ddr/interactive.c: Fix GCC 4.6 build warning
  mpc85xx: support board-specific reset function
  powerpc/85xx: verify the localbus device tree address before booting the OS
  mpc8xxx: update module_type values from JEDEC DDR3 SPD Specification
  powerpc/p3060qds: Add board related support for P3060QDS platform
  powerpc/85xx: clean up and document the QE/FMAN microcode macros
  powerpc/85xx: always implement the work-around for Erratum SATA_A001
  powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
  powerpc/85xx: Add workaround for erratum A-003474
  powerpc/85xx: fixup flexcan device tree clock-frequency
  powerpc/85xx: Add workaround for erratum CPU-A003999
2011-12-01 23:58:11 +01:00
Dirk Eibach
255ef4d909 ppc4xx: Add Io64 board support
Board support for the Guntermann & Drunck Io64.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-12-01 09:10:57 +01:00
Matthias Fuchs
2fe6b7f70f ppc4xx: use CONFIG_PCI_BOOTDELAY instead of private implementation
This patch switches PMC440 board code to the CONFIG_PCI_BOOTDELAY option
instead of using a private implemention. This relies on Anatolji's patch
that moves the pcidelay handling behind pci_target_init.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-12-01 09:10:28 +01:00
Ira W. Snyder
9839709ea3 mpc85xx: support for Freescale COM Express P2020
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.

Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.

This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 09:07:51 -06:00
Shengzhou Liu
ae6b03fefc powerpc/p3060qds: Add board related support for P3060QDS platform
The P3060QDS is a Freescale reference board for the six-core P3060 SOC.

P3060QDS Board Overview:
 Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM for RCW
 Ethernet:
  - Eight Ethernet controllers (4x1G + 4x1G/2.5G)
  - Three VSC8641 PHYs on board (2xRGMII + 1xMII)
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
 PCIe: Two PCI Express 2.0 controllers/ports
 USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
 I2C:  Four I2C controllers
 UART: Supports two dUARTs up to 115200 bps for console
 RapidIO:  Two RapidIO, sRIO1 and sRIO2

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
f2717b47ea powerpc/85xx: clean up and document the QE/FMAN microcode macros
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman.  Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both.  A given SOC will only have
a QE or an Fman, so this is safe.

Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND.  There's no way to know by looking at a variable how it's supposed
to be used.

In the future, the code which uploads QE firmware and Fman firmware will
be merged.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
3e0529f742 powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA
controller, so it should be defined in config_mpc85xx.h instead of the various
board header files.  So now CONFIG_FSL_SATA_V2 is always defined on the P1013,
P1022, P2041, P3041, P5010, and P5020.  It was already defined for the
P1010 and P1014.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Graeme Russ
a76fc70ee1 x86: Provide more configuration granularity
Planned future ports requires more granularity for some options

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-11-29 21:09:52 +11:00
Christian Riesch
f880fe5794 davinci_sonata: define CONFIG_MACH_TYPE for davinci_sonata board
This patch fixes the build breakage for the davinci_sonata board.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sergey Kubushyn <ksi@koi8.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-27 19:45:27 +01:00
Christian Riesch
ece91e3026 davinci_schmoogie: define CONFIG_MACH_TYPE for davinci_schmoogie board
This patch fixes the build breakage for the davinci_schmoogie board.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sergey Kubushyn <ksi@koi8.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-27 19:45:19 +01:00
Yan-Pai Chen
641483af40 arm: a320evb: define mach-type in board config file
MACH_TYPE_FARADAY was dropped from mach-types.h. Add it back to
board config file.

Signed-off-by: Yan-Pai Chen <ypchen@faraday-tech.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-27 19:44:49 +01:00
Stelian Pop
762e63754b Fix Stelian's email address
Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-27 19:44:21 +01:00
Stephan Linz
1de55ef105 microblaze: usable uart16550 for big endian systems
As a result of the commit 6833260 the uart16550 driver
is broken for Microblaze big endian systems, because of
the missing 3 byte offset. Other than as described, not
all U-Boot BSP will treat properly the 3 byte offset.

This why prefer to mask out the 3 byte offset in general
and setup correct _REG_SIZE value depending on edianess.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Tested-by: Michal Simek <monstr@monstr.eu>
2011-11-27 15:49:48 +01:00
Wolfgang Denk
c829ff2e3d Merge branch 'master' of git://git.denx.de/u-boot-nios
* 'master' of git://git.denx.de/u-boot-nios:
  nios2: Offer ft_board_setup() capability and call fdt_fixup_ethernet().
  board/nios2-generic: Use altera_pio driver and remove board specific driver
  gpio: Add driver for Altera's PIO core
  nios2: Pseudo implement dcache_status/enable/disable()
2011-11-21 22:00:37 +01:00
Wolfgang Denk
0c2dd9a05b Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16 20:24:41 +01:00
Wolfgang Denk
c7801ee43b Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: Fix builds of P1020/P2020RDB-PC_36BIT_NAND
  arch/powerpc/cpu/mpc8xxx/ddr/ctrl_regs.c: Fix GCC 4.6 build warning
  arch/powerpc/cpu/mpc85xx/fsl_corenet_serdes.c: Fix GCC 4.6 build warning
  arch/powerpc/cpu/mpc8xxx/ddr/options.c: Fix GCC 4.6 build warning
  drivers/qe/uec.c: Fix GCC 4.6 build warning
  drivers/usb/host/ehci-fsl.c: Fix GCC 4.6 build warning
  drivers/net/fm/fm.c: Fix GCC 4.6 build warning
  board/sbc8560/sbc8560.c: Fix GCC 4.6 build warning
  board/sbc8548/sbc8548.c: Fix GCC 4.6 build warning
  board/freescale/mpc8569mds/mpc8569mds.c: Fix GCC 4.6 build warning
  board/freescale/mpc8568mds/mpc8568mds.c: Fix GCC 4.6 build warning
  board/freescale/mpc8548cds/mpc8548cds.c: Fix GCC 4.6 build warning
  board/freescale/common/pixis.c: Fix GCC 4.6 build warning
  board/freescale/common/cds_pci_ft.c: Fix GCC 4.6 build warning
  arch/powerpc/cpu/mpc8xxx/fsl_lbc.c: Fix GCC 4.6 build warning
  arch/powerpc/cpu/mpc85xx/tlb.c: Fix GCC 4.6 build warning
  arch/powerpc/cpu/mpc85xx/cpu_init.c: Fix GCC 4.6 build warning
  phylib: Enable AR8021 phy support
  powerpc/85xx: Set max alloc length to 10MB on P1022DS
  powerpc/mpc85xx: Set SYSCLK to the required frequency
  powerpc/85xx: Fix NAND SPL support
  powerpc/85xx: Fix MPC8572DS NAND build
  fsl_ifc: Fixed a bug in the erratum handling code for IFC_A003399
  powerpc/85xx: Add support for Book-E MMU Arch v2.0
  powerpc/85xx: Make inclusion of USB device fixup conditional
  powerpc/85xx: Fix warning for USB device-fixup
  powerpc/85xx: resize the boot page TLB before relocating CCSR
  powerpc/85xx: verify the current address of CCSR before relocating it
  powerpc/85xx: add some missing sync instructions in the CCSR relocation code
  powerpc/85xx: fix some comments in the CCSR relocation code
  powerpc/85xx: fix definition of MAS register macros
  powerpc/mpc8548cds: Fix network initialization
  powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
  powerpc/QorIQ: fix network frame manager TBI PHY address settings
2011-11-16 20:06:21 +01:00
Sricharan
a9c1c04243 omap5: Add omap5_evm board build support.
This patch adds the build support for the
omap5_evm board.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
78f455c055 omap4/5: Add support for booting with CH.
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Marek Vasut
5d877f4212 PXA: vpac270: Enable the new generic MMC driver
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-15 22:24:50 +01:00
Marek Vasut
dd36d806fe PXA: Drop csb226 and innokom boards (unmaintained)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Robert Schwebel <robert@schwebel.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-11-15 22:24:50 +01:00
Jerry Huang
07b5edc206 powerpc/85xx: Set max alloc length to 10MB on P1022DS
In order to support 1920x01080 resolution, we must increase the alloc
length.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11 07:48:58 -06:00
Fabio Estevam
0249e4b7f2 m28evk: Fix comment about the number of RAM banks
m28evk has one bank of RAM.

Fix the comment.

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-11 11:36:58 +01:00
Marek Vasut
8f59bc1fc0 M28EVK: Enable USB HOST support
This enables the second port, aka. the port with the USB connector on the
M28EVK.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
2011-11-11 11:36:58 +01:00
Marek Vasut
3a4ce8335b M28: Add memory detection into SPL
This code allows the DDR DRAM size to be detected at runtime. The RAM size is
stored into two scratch registers, from which it is then fetched in U-Boot.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:58 +01:00
Marek Vasut
22fe68fbdc iMX28: Fix ARM vector handling
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue
wasn't addressed because the interrupts weren't enabled on any ARMv5 core,
therefore the issue wasn't noticed earlier.

In previous implementation, the vectoring code used by i.MX28 CPU when an
exception happened was that of the SPL. With this change, the branch target when
an exception happens can be reconfigured by U-Boot.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:58 +01:00
Marek Vasut
04fe4273d3 M28: Add MMC SPL
This patch adds SPL code for the M28 board.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:57 +01:00
Marek Vasut
fc10272856 iMX28: Add support for DENX M28EVK board
This contains support for the following components:
- DUART
- MMC
- Both FEC interfaces
- NAND
- I2C (RTC, EEPROM)
- SPI (FLASH)

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:57 +01:00
Nagabhushana Netagunte
06194b6b65 da850: add new config file for AM18xx
add new configuration file da850_am18xxevm.h for AM18xx boards
which are based on da850 SOC. AM18xx has WINBOND spi flash which
is indicated in the config file. And make appropriate changes in
board.cfg for building.

Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-10 16:30:41 +01:00
Alexander Holler
73ce500373 BeagleBoard: config: Switch to ttyO2
This is needed to support the latest kernel versions.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-10 16:30:41 +01:00
Tom Rini
c471ccb967 devkit8000: Fix NAND SPL on boards with 256MB NAND
The devkit8000 ships with either a 128MB or 256MB NAND chip.  In
order for SPL to work with 256MB NAND CONFIG_SYS_NAND_5_ADDR_CYCLE
needs to be set.  After talking with Scott Wood this should be
safe to set even for smaller NAND chips.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-10 16:30:40 +01:00
Linus Walleij
a4c15c01bf integrator: move text offset to config
Do away with the config.mk file and move the text offset to the
config files to make things easier.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-11-10 15:26:58 +01:00
Macpaul Lin
6cb144bc26 adp-ag101p: Add SoC and board support of ag101p
Add softcore SoC ag101p and the board adp-ag101p support.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-11-10 10:46:54 +08:00
Kumar Gala
8d22ddca3d powerpc/85xx: Fix NAND SPL support
We cause CCSRBAR to be relocated in the SPL phase of NAND boot which
isn't expected and breaks things.  Fixing the board config.h to NOT
relocate CCSR during the CONFIG_NAND_SPL phase.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-09 09:13:39 -06:00
Asen Dimov
a3e09cc28c ARM: define CONFIG_MACH_TYPE for all ronetix boards
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-08 20:34:53 +01:00
chenhui zhao
d37012289d powerpc/mpc8548cds: Fix network initialization
Add board_eth_init(). PCIe network card is also supported.
Put RGMII init after tsec_eth_init().
Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3.

Signed-off-by: Ebony Zhu
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
2011-11-08 08:30:47 -06:00
Manjunath Hadli
b79df8f8f8 dm646x: pass board revision info to kernel
add a function in board file to pass board revision
info to kernel. Revision number 0 and 1 are passed in
case of DM6467 and DM6467T respectively.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-08 08:59:57 -05:00
Manjunath Hadli
2d575e4685 dm646x: add new configuration for dm6467T
add new configuration file for dm6467T and appropraite changes
in boards.cfg. dm6467T is the new varaiant of dm6467 SOC which
supports 33 MHz reference clock where as dm6467 supports 27 MHz
reference clock.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-08 08:59:54 -05:00
David Müller (ELSOFT AG)
c686537f34 ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
2011-11-08 09:18:23 +01:00
Wolfgang Denk
5721385b18 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
* 'master' of git://git.denx.de/u-boot-mpc83xx:
  powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
  powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds
  mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code
  mpc83xx: Cleanup usage of LBC constants
  mpc83xx: Cleanup usage of DDR constants
  mpc83xx: Cleanup usage of BAT constants
  mpc83xx: cosmetic: vme8349.h checkpatch compliance
  mpc83xx: cosmetic: ve8313.h checkpatch compliance
  mpc83xx: cosmetic: sbc8349.h checkpatch compliance
  mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance
  mpc83xx: cosmetic: kmeter1.h checkpatch compliance
  mpc83xx: cosmetic: TQM834x.h checkpatch compliance
  mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance
  mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
  mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance
  mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
  mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
  mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance
  mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance
  mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance
  mpc83xx: Fix ipic structure definition
  powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions
  cosmetic, powerpc, mpc83xx: checkpatch cleanup
  powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c
  mpc83xx: fix global timer structure definition
2011-11-08 07:44:52 +01:00
Jerry Huang
6be55ee225 powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
The new MPC8360EMDS board changes the oscillator to 33.33MHz
in order to support QE 500MHz since 2008.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-07 18:34:40 -06:00
Wolfgang Denk
688d8f33f2 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
  arm: jadecpu: Readd MACH_TYPE_JADECPU
  at91: defined mach-types for otc570 board in board config file
  at91: defined mach-types for meesc board in board config file
  mx31pdk: Enable D and I caches
  ehci-mxc: remove incorrect comment
  README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
  mx53: Turn off child clocks before reconfigure perclk_root
  qong: enable support for compressed images
  imx: imx31_phycore.h: fix checkpatch warnings
  vision2: Remove unused get_board_rev function
  mx53smd: Remove unused get_board_rev function
  mx53ard: Remove unused get_board_rev function
  mx53evk: Remove unused get_board_rev function
  mx53evk: Add RTC support
  mx53loco: Remove unused get_board_rev function
  mx53evk: Remove unneeded '1' from mx53evk.h
  OMAP3: mvblx: Initial support for mvBlueLYNX-X
  ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
  omap3: mem: Move comments next to definitions
  omap3: mem: Clean-up whitespaces
  omap3: mem: Define and use common macros
  Davinci: ea20: added PREBOOT to configuration
  Davinci: ea20: added I2C support
  Davinci: ea20: added video support
  VIDEO: davinci: add framebuffer to da8xx
  ARM: Davinci: added missing registers to hardware.h
  Davinci: ea20: add gpios for LCD backlight control
  Davinci: ea20: add gpio for keeping power on in board_late_init
  Davinci: ea20: Add default U-Boot environment
  Davinci: ea20: Add early init to get early output from console
  Davinci: ea20: Add NAND support
  Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
  Davinci: ea20: set console on UART0
  arm, davinci: add cam_enc_4xx support
  arm926ejs, davinci: add missing spi defines for dm365
  arm926ejs, davinci: add cpuinfo for dm365
  arm, davinci: add lowlevel function for dm365 soc
  arm, davinci: add header files for dm365
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  arm, davinci: add support for new spl framework
  spl: add option for adding post memory test to the SPL framework
  net, davinci_emac: make clock divider in MDIO control register configurable
  arm, usb, davinci: make USBPHY_CTL register configurable
  usb, davinci: add enable_vbus() weak function
  omap3evm: fix errors caused by multiple definitions
  omap3evm: Add (quick) configuration for NAND only
  omap3evm: Add (quick) configuration for MMC/SD only
  omap3evm: move common config options to new file
  omap3evm: Prepare to split configuration
  omap3evm: Reorder related config options
  omap/spl: actually enable the console
  davinci_emac: compilation fix, phy is array now
  omap3evm: Set environment variable 'ethaddr'
  arm, arm926: fix missing symbols in NAND_SPL mode
  arm, davinci: Add function lpsc_syncreset()
  arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
  arm/km: portl2 environment address update to P1B
  arm/km: adapt bootcounter evaluation
  arm/km: enable jffs2 cmds
  arm/km: trigger reconfiguration for the Xilinx FPGA
  arm/km: add boardid and hwkey to kernel command line
  ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
  netspace_v2: enable I2C EEPROM support
  netspace_v2: fix SDRAM configuration
  armada100: define CONFIG_SYS_CACHELINE_SIZE
  pantheon: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: drop empty asm-offsets.s file
  arm/km/mgcoge3un: enhance "waitforne" feature
  arm/km: add variable waitforne to mgcoge3un
  gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
  ARM: dreamplug: fix compilation
  ARM: DockStar: fix compilation
  ARM: netspace_v2: fix warnings
  am335x: Drop board_sysinfo struct
  am335x: Temporarily add MACH_TYPE define
  misc:pmic:samsung Enable PMIC driver at C210 Universal target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
  smdkv310: use macro for mmc data read function address
  smdkv310: use spl framework for mmc spl
  SMDKV310: use get_ram_size() to validate dram size
  SMDKV310: Initialize board id using CONFIG_MACH_TYPE
  ORIGEN : use absolute paths and fix tool naming
  ORIGEN : enable device tree support
  MX25: tx25: Fix building due to missing MACH_TYPE
  mx31: Add board support for HALE TT-01
  mx31: add ESD control registers
  mx31: define pins and init for UART2 and CSPI3
  MX35: add support for flea3 board
  MX51: vision2: add MACH_TYPE in config file
  vision2: Remove unused header file
  mx51evk: Remove unused get_board_rev function
  mx51evk: Remove unneeded '1' from mx51evk.h
  I2C: Fix mxc_i2c.c problem on imx31_phycore
  mx35pdk: Add RTC support
  mx51evk: Use GPIO API for configuring the IOMUX
  mx51evk: Add RTC support
  rtc: Make mc13783-rtc driver generic
  qong: remove unneeded IOMUX settings
  qong: Use mx31_set_gpr to setup USBH2 pins
  mx31: Introduce mx31_set_gpr function
  mx31pdk: Add MC13783 PMIC support
  qong: remove unneeded "1" from qong.h
  misc: pmic: fix regression in pmic_fsl.c (SPI)
  mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
  MX35: Drop unnecessary prototypes from imx-regs.h
  I2C: added I2C-2 and I2C-3 to MX35
  MX35: factorize common assembly code
  MX35: add reset cause as provided by other i.MX
  MX35: add pins definition for UART3
  MX35: added ESDC structure to imx-regs
2011-11-08 00:38:52 +01:00
Wolfgang Denk
7ba6d591b5 Merge branch 'master' of git://git.denx.de/u-boot-coldfire
* 'master' of git://git.denx.de/u-boot-coldfire:
  ColdFire: The EB+MCF-EV123 boards config update
  ColdFire: Fix the compile issue for M52277
  ColdFire:Moving the remaining coldfire boards to boards.cfg
2011-11-08 00:37:27 +01:00
Wolfgang Denk
e7e0010412 TQM850M: Add missing CONFIG_BOOTDELAY
This also fixes a build warning:
main.c: In function 'main_loop':
main.c:311:16: warning: variable 'bootlimit' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07 22:15:46 +01:00
Jason Jin
27f7ae70d6 ColdFire: Fix the compile issue for M52277
After commit 327474f854, the
M52277EVB_stmicro configuration fail to build. Fix it by moving
the env outside the flash and update the lds file.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2011-11-07 22:02:33 +08:00
Jens Scharsig
2026a11951 Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
* re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2011-11-05 13:43:27 +01:00
Matthias Weisser
b2a7badb5a arm: jadecpu: Readd MACH_TYPE_JADECPU
MACH_TYPE_JADECPU was removed from mach-types.h. Add it to board
config file.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-11-05 13:36:31 +01:00
Daniel Gorsulowski
b2f2648d89 at91: defined mach-types for otc570 board in board config file
quotation from Albert ARIBAUD:
"Recently the ARM mach-types.h file has been brought in sync with its
Linux original, leasing to a number of boards not being listed any more,
as the new list only contains boards which have actual Linux support or
were declared less than one year ago.

The symptom is a build failure with a message of the form "error:
'MACH_TYPE_XXXXXX' undeclared (first use in this function)".

U-Boot maintainers of such boards (in Cc: of this mail) should provide a
patch to re-introduce the MACH_TYPE_XXXXXX definition in their boards'
config header file in include/configs/."

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2011-11-05 10:40:47 +01:00
Daniel Gorsulowski
18b6ddfdf1 at91: defined mach-types for meesc board in board config file
quotation from Albert ARIBAUD:
"Recently the ARM mach-types.h file has been brought in sync with its
Linux original, leasing to a number of boards not being listed any more,
as the new list only contains boards which have actual Linux support or
were declared less than one year ago.

The symptom is a build failure with a message of the form "error:
'MACH_TYPE_XXXXXX' undeclared (first use in this function)".

U-Boot maintainers of such boards (in Cc: of this mail) should provide a
patch to re-introduce the MACH_TYPE_XXXXXX definition in their boards'
config header file in include/configs/."

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2011-11-05 10:40:43 +01:00
Wolfgang Denk
544aa66a66 qong: enable support for compressed images
- enable support for unzip command
- enable support for compressed bitmap images

We also have to increase the malloc() arena a bit for this.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2011-11-04 22:06:37 +01:00
Anatolij Gustschin
6ac1c9033a imx: imx31_phycore.h: fix checkpatch warnings
Cleanup board config file and fix issues reported by
checkpatch.pl script.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-04 22:06:37 +01:00
Fabio Estevam
e99be76907 vision2: Remove unused get_board_rev function
No board information is passed for VISION2, so remove get_board_rev function.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-11-04 22:06:37 +01:00
Fabio Estevam
6bc31fbe08 mx53smd: Remove unused get_board_rev function
No board information is passed for MX53SMD, so remove get_board_rev function.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-11-04 22:06:37 +01:00
Fabio Estevam
d7f71414f4 mx53ard: Remove unused get_board_rev function
No board information is passed for MX53ARD, so remove get_board_rev function.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-11-04 22:06:37 +01:00
Fabio Estevam
850f4d6773 mx53evk: Remove unused get_board_rev function
No board information is passed for MX53EVK, so remove get_board_rev function.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2011-11-04 22:06:37 +01:00
Fabio Estevam
4f97c88ea1 mx53evk: Add RTC support
MX53EVK has an MC13892 PMIC. Add RTC support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu < jason.hui@linaro.org>
2011-11-04 22:06:37 +01:00
Fabio Estevam
aa2bcf4be5 mx53loco: Remove unused get_board_rev function
No board information is passed for MX53LOCO, so remove get_board_rev function.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2011-11-04 22:06:37 +01:00
Fabio Estevam
a7abca01cb mx53evk: Remove unneeded '1' from mx53evk.h
Remove unneeded '1' from mx53evk.h.

Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
2011-11-04 22:06:37 +01:00
Michael Jones
84d7a0171f OMAP3: mvblx: Initial support for mvBlueLYNX-X
Add support for the MATRIX VISION mvBlueLYNX-X, an OMAP3-based
intelligent camera.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-04 13:54:33 -04:00
Luca Ceresoli
30dca9ddad ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
MACH_TYPE_OMAP3_CPS was dropped in the latest mach-types sync (47af6f61bc)
because it is not mainlined in Linux.

Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-04 13:42:09 -04:00
Jerry Huang
d37be07ee5 powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds
The new MPC8360EMDS board supports 512MB DDR since 2008.

For 512MB DDR:
BAT0 is used for the first 256MB memory, BAT4 is used for the second
256MB memory and the address space of SDRAM follows the DDR, so if the
size of DDR is 256MB, the BAT4 will be used for SDRAM and if the size of
DDR is 512MB, the BAT4 will be used for the second 256MB memory and
there is no BAT for SDRAM.
Therefore, if the size of DDR is 512MB, this patch will use BAT6 for
SDRAM and BAT5 will be used for PCI MEM to replace the BAT6 after the
codes relocates to the DDR.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
2e651b2483 mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code
Rename CONFIG_SYS_DDR_CONFIG to include which CS it is configuring
Cleanup the setting of the csnbds to respect the setting of
CONFIG_SYS_DDR_SDRAM_BASE
Use __ilog2 instead of writing the code to compute it
Disable unused CS configs
Ensure ddrlaw.bar is configured

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
7d6a098219 mpc83xx: Cleanup usage of LBC constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
2fef402097 mpc83xx: Cleanup usage of DDR constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
72cd4087c9 mpc83xx: Cleanup usage of BAT constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
c7357a2b90 mpc83xx: cosmetic: vme8349.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
be29fa71b0 mpc83xx: cosmetic: ve8313.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
60e1dc151e mpc83xx: cosmetic: sbc8349.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
80ae4df929 mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
b43b12e6b1 mpc83xx: cosmetic: kmeter1.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Joe Hershberger
df939e1647 mpc83xx: cosmetic: TQM834x.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Joe Hershberger
bb0f5bc92d mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Joe Hershberger
b2773a5e1c mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Joe Hershberger
5afe9722b0 mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Joe Hershberger
8d85808fa1 mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Joe Hershberger
9a9865508f mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:53 -05:00
Joe Hershberger
1f5cb79374 mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:53 -05:00
Joe Hershberger
396abba261 mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:53 -05:00
Joe Hershberger
32795ecad6 mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:53 -05:00
Joe Hershberger
989091acb0 mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:53 -05:00
Joe Hershberger
4dde49d8cb mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Joe Hershberger
6f681b7349 mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Joe Hershberger
261c07bc67 mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Joe Hershberger
34f819685c mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Joe Hershberger
7c3a4f986c mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:52 -05:00
Stefano Babic
92e86c8dae Davinci: ea20: added PREBOOT to configuration
PREBOOT is used on the ea20 to load a splash image
at the start up.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:26 +01:00
Stefano Babic
4205987a66 Davinci: ea20: added I2C support
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:26 +01:00
Stefano Babic
3c8910116c Davinci: ea20: added video support
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:26 +01:00
Bastian Ruppert
e5ee9125ec Davinci: ea20: add gpio for keeping power on in board_late_init
The pin called HALTEN drives a transistor to operate the supply
voltage. After HALTEN is high, the user can release the power
switch button and the device will stay powered on.

Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: sbabic@denx.de
CC: dzu@denx.de
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:26 +01:00
Stefano Babic
2084f21b05 Davinci: ea20: Add default U-Boot environment
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:26 +01:00
Stefano Babic
17a8904b27 Davinci: ea20: Add NAND support
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Bastian Ruppert
f9fc237f1f Davinci: ea20: set console on UART0
Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Heiko Schocher
4dd834906d arm, davinci: add cam_enc_4xx support
- DM368 SOC
- booting with spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
  the RAM with the post memory test. If error
  is found, switch all LEDs on and halt system.
- SPI Flash
  Dataflash Typ: M25PE80
- Ethernet DM9161BI
- MMC
- USB

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Sanjeev Premi
edc633ea77 omap3evm: fix errors caused by multiple definitions
Fix these errors when building with recently added
omap3_evm_quick_nand_config:

env_nowhere.o: In function `env_relocate_spec':
/home/premi/u-boot/common/env_nowhere.c:40: multiple definition
 of `env_relocate_spec'
env_nand.o:/home/premi/u-boot/common/env_nand.c:416: first defi
ned here
env_nowhere.o: In function `env_get_char_spec':
/home/premi/u-boot/common/env_nowhere.c:44: multiple definition
 of `env_get_char_spec'
env_nand.o:/home/premi/u-boot/common/env_nand.c:77: first defin
ed here
env_nowhere.o: In function `env_init':
/home/premi/u-boot/common/env_nowhere.c:54: multiple definition
 of `env_init'
env_nand.o:/home/premi/u-boot/common/env_nand.c:144: first defi
ned here
env_nowhere.o: In function `env_relocate_spec':
/home/premi/u-boot/common/env_nowhere.c:40: multiple definition
 of `env_ptr'
env_nand.o:/home/premi/u-boot/common/env_nand.c:77: first defin
ed here

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Sanjeev Premi
16885db919 omap3evm: Add (quick) configuration for NAND only
Add an optimized board configuration that only
supports boot from NAND.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Sanjeev Premi
7f732099a6 omap3evm: Add (quick) configuration for MMC/SD only
Add an optimized board configuration that only
supports boot from MMC/SD.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Sanjeev Premi
3970884c84 omap3evm: move common config options to new file
This patch moves common config options to a new
file. Common options can now be included in other
board configs for this evm.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Sanjeev Premi
741de26618 omap3evm: Prepare to split configuration
This patch marks the beginning of steps that would
lead to clean and easy split of the configuration
file. Common portion can then be re-used by other
configurations.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Sanjeev Premi
ee8e225400 omap3evm: Reorder related config options
This patch brings related config options together.
Most config options won't be evaluated for numerical
value, but they are being set to 1. This patch also
removes this assignment.

Some formatting changes were also done for consistent
look-n-feel after the movement.

The patch doesn't make/include any other functional
change.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Thomas Herzmann
5e454e0ace arm/km: portl2 environment address update to P1B
The environment eeprom is now at a different MUX address.

Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-11-03 22:56:23 +01:00
Holger Brunck
c5dd978517 arm/km: enable jffs2 cmds
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-11-03 22:56:23 +01:00
Holger Brunck
f0d6425790 arm/km: trigger reconfiguration for the Xilinx FPGA
The Xilinx FPGA must be reconfigured each time the unit
reboots. The FPGA is connected to the GPIO pin 39 from kirkwood.
This patch triggers this pin for km_kirkwood_pci targets.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-11-03 22:56:23 +01:00
Holger Brunck
66072a8ca0 arm/km: add boardid and hwkey to kernel command line
We need in some cases a possibility for the kernel to distinguish
on which board he is running. On powerpc we did this with different
dts files. On arm currently we can't do this, so add boardid and
hwkey to the kernel command line and use it later on in the kernel
code.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2011-11-03 22:56:22 +01:00
Valentin Longchamp
8620ca2a1f ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
We got dropped from Linux mach-types.h because of a lack of mainline
support and this is needed since the last Linux/u-boot mach-types
synchro.

This patch also defines CONFIG_MACH_TYPE for all keymile boards, as
this is a mandatory CONFIG for ARM boards now. The initialization
of gd->bd->bi_arch_number is removed form km_arm.c, our board file.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2011-11-03 22:56:22 +01:00