Commit Graph

6817 Commits

Author SHA1 Message Date
Hans de Goede 906f609681 sun4i: add USB EHCI settings
Specific USB EHCI settings to be set for sun4i if CONFIG_USB_EHCI is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-31 15:37:23 +02:00
Roman Byshko 263b012c25 sun7i: add USB EHCI settings
Specific USB EHCI settings to be set for sun7i if
CONFIG_USB_EHCI is enabled.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Use SUNXI_GPH macro for SUNXI_USB_VBUS#_GPIO]
[hdegoede@redhat.com: Add #ifndef SUNXI_USB_VBUS#_GPIO to allow override of
 the default pins from boards.cfg]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:23 +02:00
Roman Byshko 3584f30ce9 sunxi: add general USB settings
General configuration settings to be set if CONFIG_USB_EHCI
is enabled for an Allwinner aka sunxi SoC.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Ian Campbell a6e50a88d8 ahci: provide sunxi SATA driver using AHCI platform framework
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.

The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.

The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port.  This is added under a
suitable ifdef.

This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-07-31 15:37:22 +02:00
Masahiro Yamada 25b4adbba0 include: remove CONFIG_SPL/CONFIG_TPL definition in config headers
Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig.

Remove the redundant definition in config headers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 14:42:03 -04:00
Masahiro Yamada 90f984e397 kconfig: delete redundant CONFIG_${ARCH} definition
CONFIG_${ARCH} is defined by Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 14:42:02 -04:00
Masahiro Yamada 4ce9957029 include: define CONFIG_SPL and CONFIG_TPL as 1
We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.

In Kconfig, include/generated/autoconf.h defines boolean
CONFIG macros as 1.

CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1.
Otherwise, when switching to Kconfig, the build log
would be sprinkled with warning messages like this:
  warning: "CONFIG_SPL" redefined [enabled by default]

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:02 -04:00
Tom Rini 362f16b1e9 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-07-29 09:41:35 -04:00
Tom Rini 302e609fe6 Merge git://www.denx.de/git/u-boot-ppc4xx 2014-07-28 17:48:48 -04:00
Tom Rini d5f8a6ddd4 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-07-28 14:54:29 -04:00
Albert ARIBAUD b1cdd8baa1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-28 12:26:21 +02:00
Albert ARIBAUD 48b3ed217f Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master' 2014-07-28 10:54:54 +02:00
Albert ARIBAUD 740f41d3cb Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-07-28 10:12:45 +02:00
Albert ARIBAUD f2c8d7f591 Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master' 2014-07-26 14:08:36 +02:00
pekon gupta 434f2cfcad ARM: omap: move board specific NAND configs out from ti_armv7_common.h
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO:   individual board config files using these configs.
So that each board can independently set the value as per its design.

Following configs are affected in this patch:
  CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
  CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
  CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
  CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>

This patch also updates documentation for few of above NAND configs.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
pekon gupta 222a3113b4 ARM: omap: clean redundant PISMO_xx macros used in OMAP3
PISMO_xx macros were used to define 'Platform Independent Storage MOdule'
related GPMC configurations. This patch
- Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided
  by current u-boot infrastructure.
- Removes unused redundant macros, which are no longer required after
  merging of common platform code in following commit
      commit a0a37183bd
      ARM: omap: merge GPMC initialization code for all platform

+-----------------+-----------------------------------------------------------+
| Macro           | Reason for removal                                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE                         |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE                      |
+-----------------+-----------------------------------------------------------+
| PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so     |
|                 | configuring GPMC chip-select for smallest allowable       |
|                 | segment (GPMC_SIZE_16M) is enough.                        |
+-----------------+-----------------------------------------------------------+
| PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of    |
|                 | 128MB (GPMC_SIZE_128M)                                    |
+-----------------+-----------------------------------------------------------+
+-----------------+-----------------------------------------------------------+
| PISMO1_NOR      |  Unused Macros                                            |
| PISMO1_NAND     |                                                           |
| PISMO2_CS0      |                                                           |
| PISMO2_CS1      |                                                           |
| PISMO1_ONENAND  |                                                           |
| PISMO2_NAND_CS0 |                                                           |
| PISMO2_NAND_CS1 |                                                           |
| PISMO1_NOR_BASE |                                                           |
| PISMO1_NAND_BASE|                                                           |
| PISMO2_CS0_BASE |                                                           |
+-----------------+-----------------------------------------------------------+

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
pekon gupta 77cd89e755 ARM: omap: fix GPMC address-map size for NAND and NOR devices
Fixes commit a0a37183bd
    ARM: omap: merge GPMC initialization code for all platform

1) NAND device are not directly memory-mapped to CPU address-space, they are
 indirectly accessed via following GPMC registers:
 - GPMC_NAND_COMMAND_x
 - GPMC_NAND_ADDRESS_x
 - GPMC_NAND_DATA_x
 Therefore from CPU's point of view, NAND address-map can be limited to just
 above register addresses. But GPMC chip-select address-map can be configured
 in granularity of 16MB only.
 So this patch uses GPMC_SIZE_16M for all NAND devices.

2) NOR device are directly memory-mapped to CPU address-space, so its
 address-map size depends on actual addressable region in NOR FLASH device.
 So this patch uses CONFIG_SYS_FLASH_SIZE to derive GPMC chip-select address-map
 size configuration.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
Hao Zhang a906847966 board: k2e-evm: add board support
This patch adds Keystone2 k2e_evm evaluation board support.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang 4dca7f0acc ARM: keystone2: clock: add K2E clock support
This patch adds clock definitions and commands to support Keystone2
K2E SOC.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:11 -04:00
Hao Zhang 2221cd12cd configs: k2hk_evm: config: add common EVM configuration header
This patch adds a common config header file for all the Keystone II
EVM platforms. It combines a lot of general definitions in one file.
The common header included in the EVM should be specific configuration
header.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Hao Zhang e595107ebb ARM: keystone2: move K2HK board files to common KS2 board directory
This patch moves K2HK board directory to a common Keystone II board
directory. The Board related common functions are moved to a common
keystone board file.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Khoronzhuk, Ivan 3d31538625 k2hk: use common KS2_ prefix for all hardware definitions
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.

Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 16:26:10 -04:00
Stefan Roese 188948e884 ARM: omap: tao3530: Convert to generic board
Use generic board setup functions by defining
CONFIG_SYS_GENERIC_BOARD.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
2014-07-25 16:26:09 -04:00
Andreas Bießmann e6f9d419c8 tricorder: convert to generic board
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Thomas Weber <thomas.weber@corscience.de>
2014-07-25 16:26:08 -04:00
Khoronzhuk, Ivan c6ac7e3bdc k2hk_evm: add script to automate NAND flash process
Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
2014-07-25 15:21:06 -04:00
Khoronzhuk, Ivan 67ac6ffaee mtd: nand: davinci: add opportunity to write keystone U-boot image
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.

The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.

The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.

Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 15:21:06 -04:00
Tom Rini 7aa5598aac tps65218/am43xx_evm: Add power framework support to TPS65218
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-07-25 15:21:06 -04:00
Dirk Eibach d9f923ffcb board: Add CONFIG_SYS_GENERIC_BOARD to all gdsys boards
Add the generic board infrastructure to all gdsys boards.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2014-07-25 10:55:49 +02:00
Nobuhiro Iwamatsu cff2f5f09e arm: rmobile: Add support Alt board
The alt board has R8A7794, 1GB DDR3-SDRAM, USB, Ethernet, QSPI,
MMC, SDHI and more.

This commit supports the following functions:
 - DDR3-SDRAM
 - SCIF
 - I2C
 - Ethernet
 - QSPI

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-07-24 14:03:46 +09:00
Shengzhou Liu fb5368789a board/freescale: use generic board architecture for t2080qds and t2080rdb
Tested with NOR boot and NAND boot on T2080QDS and T2080RDB.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-07-23 12:40:30 -07:00
Michal Simek 2b25721645 ARM: zynq: Enable generic board for Xilinx Zynq
Enable CONFIG_SYS_GENERIC_BOARD for all Zynq boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com> [on ZC706 board]
2014-07-23 15:28:22 +02:00
Simon Glass 709ea543b9 stdio: Pass device pointer to stdio methods
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.

For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.

Instead, add a stdio_dev pointer to each of the stdio member functions.

Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.

Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.

22: stdio: Pass device pointer to stdio methods
       arm: (for 2/2 boards)  all +244.0  bss -4.0  text +248.0
   powerpc: (for 1/1 boards)  all +428.0  text +428.0

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2014-07-23 14:07:23 +01:00
Simon Glass b53e94b132 sandbox: config: Enable pre-relocation malloc()
Enable this for sandbox so that we will be able to use driver model before
relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-07-23 14:06:17 +01:00
Shengzhou Liu b0d97cd2ed powerpc/t1040: update i2c for t1040qds and t104xrdb
- Fix base address of I2C2 as 0x118100 instead of 0x119000.
- Add definitions for I2C3 & I2C4.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:55 -07:00
Shaohui Xie de51916310 powerpc/ifc: fix invalid CSn FTIM2.TCH setting
On some platforms, CSn FTIM2.TCH is set to zero which is invalid,
an invalid hold time makes DUT timing variances, whether it works
or not on luck.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:55 -07:00
Lijun Pan d0bc51407c powerpc/mpc85xx: Remove P1023 RDS support
Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.

Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Shengzhou Liu 09c2046ff6 board/t2080qds: enable sst and eon spi flash for nor boot
Remove unnecessary condition CONFIG_RAMBOOT_PBL to
have SST and EON SPI flash work in case of NOR boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Alexander Holler 11547b2992 rpi_b: handle import of environments in files with CRLF as line endings
Use the new option -r for env import.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
2014-07-22 07:44:26 -04:00
Alexander Holler 4cfe8c3edd am335x_evm: handle import of environments in files with CRLF as line endings
Use the new option -r for env import.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
2014-07-22 07:44:26 -04:00
Alexander Holler 44bd26fa99 omap3_beagle: handle import of environments in files with CRLF as line endings
Use the new option -r for env import.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
2014-07-22 07:44:26 -04:00
Tom Rini 8973601c38 h2200: Disable SHA256 on FIT images
This board is close in binary size to one of its hard limits, so disable
SHA256 FIT image support to gain some breathing room.

Signed-off-by: Tom Rini <trini@ti.com>
2014-07-22 07:44:26 -04:00
Ian Campbell abce2c6220 sunxi: add gpio driver
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2014-07-18 19:42:25 +01:00
Jonathan Liu b41d7d05b7 sunxi: use random parts of SID to set ethaddr
Similar to the USB NIC found on OMAP5uEVM, PandaBoard and BeagleBoard-XM
boards, the sunxi SoCs have a NIC onboard without an embedded MAC address.

Just like the omap used on these boards, the sunxi SoCs do have a unique chip
id, in the form of the 128 bit SID register:
http://linux-sunxi.org/SID_Register_Guide

So mimick the BeagleBoard-XM board code (commit 548a64d8) and use the chip id
to generate a unique fixed MAC address.

We check for the SID not being all 0, since some early A20 batches
shipped without having there SID programmed.

Note we use specific parts of the 128 bits, since some parts indicate the
SoC family / revision, and thus are fixed. The algorithm for this was taken
from the linux-sunxi.org kernels.

Signed-off-by: Jonathan Liu <net147@gmail.com>
[hdegoede@redhat.com: Expanded the commit message with some more info]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-18 19:42:22 +01:00
Henrik Nordstrom 14bc66bd9a sunxi: Add axp209 pmic support
Add support for the x-powers axp209 pmic which is found on most A10, A13 and
A20 boards.

And enable AXP209 support for the Cubietruck and Cubieboard boards.

Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-18 19:42:10 +01:00
Hans de Goede 6620377e4b sunxi: Add i2c support
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
2014-07-18 19:41:30 +01:00
Hans de Goede 0db2bbdc04 mvtwsi: convert to CONFIG_SYS_I2C framework
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).

The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-07-16 19:56:24 +01:00
Pavel Machek 2cc0ea72ef socfpga: timer actually counts down
Timer on cyclone5 actually counts down. It took me a while to figure
out, as timer counting in wrong direction actually _can_ be used, it
just appears to tick at extremely high frequency in u-boot.

The bug was introduced in commit
23ab7ee0ff.

Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2014-07-14 11:21:35 -04:00
Lokesh Vutla 4ec3f6e510 ARM: DRA7xx: Update the board_name env variable
Update the board_name env variable and accordingly
populate the dtb file.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-07-14 11:16:38 -04:00
Tom Rini 22692ec0fb Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-07-09 09:21:51 -04:00
Lothar Rubusch 85d8a5fc98 ARM: m53evk: Update default environment
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lothar Rubusch <lothar@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-07-09 14:54:04 +02:00