Commit graph

448 commits

Author SHA1 Message Date
Prabhakar Kushwaha
41d910118c powerpc/85xx: Add BSC9132QDS support
BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.

BSC9132QDS Overview
 --------------------
  2Gbyte DDR3 (on board DDR), Dual Ranki
  32Mbyte 16bit NOR flash
  128Mbyte 2K page size NAND Flash
  256 Kbit M24256 I2C EEPROM
  128 Mbit SPI Flash memory
  SD slot
  USB-ULPI
  eTSEC1: Connected to SGMII PHY
  eTSEC2: Connected to SGMII PHY
  PCIe
  CPRI
  SerDes
  I2C RTC
  DUART interface: supports one UARTs up to 115200 bps for console display

Apart from the above it also consists various peripherals to support DSP
functionalities.

This patch adds support for mainly Power side functionalities and peripherals

Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:14 -06:00
York Sun
b5b06fb7b0 powerpc/b4860qds: Added Support for B4860QDS
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
	- On-board eCWTAP controller with ETH and USB I/F
	- JTAG/COP 16-pin header for any external TAP controller
	- External JTAG source over AMC to support B2B configuration
	- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
	- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:11 -06:00
Kim Phillips
a6187dccd8 Merge remote-tracking branch 'mpc83xx/next' 2013-01-16 18:34:09 -06:00
Bo Shen
961ffc7759 arm: at91sam9x5: add dataflash boot support
Add dataflash boot support on at91sam9x5ek board

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-01-12 13:18:50 +01:00
Tom Rini
7a8e739cd5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-01-11 14:38:24 -07:00
Albert ARIBAUD
7202e8ae51 ARM: lacie_kw: add support for WIRELESS_SPACE
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-01-09 04:12:10 +05:30
Tom Rini
da77a0e593 Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-12-22 05:55:19 -07:00
Tom Rini
42e1321874 Merge branch 'master' of git://git.denx.de/u-boot-sh 2012-12-20 10:53:20 -07:00
Yoshihiro Shimoda
1a2621bab8 sh: add support for sh7752evb board
The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM,
Gigabit Ethernet, and eMMC.

This patch supports the following functions:
 - 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-12-20 13:20:17 +09:00
Scott Wood
22f4442d12 powerpc/mpc83xx: convert MPC8313ERDB to new-SPL
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-12-19 17:45:54 -06:00
Jens Scharsig (BuS Elektronik)
46dc5bcade coldfire: eb_cpu5282: fix: boot from internal flash
* By a sequence of unfavorable conditions in the config header file, the eb_cpu5282
  booting from  internal stopped after relocation. Blame it is a faulty value of
  CONFIG_SYS_MONITOR_BASE. This patch fix this by replace the wrong condition in
  config header with option in board.cfg

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-12-19 15:51:58 -07:00
Minkyu Kang
2c601c7208 Merge branch 'master' of git://git.denx.de/u-boot into resolve
Conflicts:
	README
	board/samsung/universal_c210/universal.c
	drivers/misc/Makefile
	drivers/power/power_fsl.c
	include/configs/mx35pdk.h
	include/configs/mx53loco.h
	include/configs/seaboard.h
2012-12-10 14:13:27 +09:00
Gabe Black
112a575e49 x86: Override calculate_relocation_address to use the e820 map
Because calculate_relocation_address now uses the e820 map, it will be able
to avoid addresses over 32 bits and regions that are at high addresses but
not big enough for U-Boot. It also means we can remove the hack which
limitted U-Boot's idea of the size of memory to less than 4GB.

Also take into account the space needed for the heap and stack, so we avoid
picking a very small region those areas might overlap with something it
shouldn't.

Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-06 14:30:42 -08:00
Stefan Roese
13b4f63949 mpc5200: Add a3m071 board support
This patch adds support for the a3m071 board based on the
MPC5200.

Signed-off-by: Stefan Roese <sr@denx.de>
2012-12-05 17:31:23 +01:00
Tom Rini
a86fcff695 Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx 2012-11-28 08:30:21 -07:00
Timur Tabi
d31e53b42c powerpc/85xx: add support for the Freescale P5040DS Superhydra reference board
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:06 -06:00
Wu, Josh
b7e3129e55 mmc: at91sam9x5: support to save environment in mmc
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:47 -06:00
Jens Scharsig (BuS Elektronik)
d858c335bf M68K: eb_cpu5282: general update and enhanced board support
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2012-11-14 12:16:50 +01:00
Stefano Babic
3e4d27b06d Merge git://git.denx.de/u-boot 2012-11-10 08:05:54 +01:00
Tom Rini
6acc7c3cbc Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-11-05 07:42:00 -07:00
Albert ARIBAUD
a42c87f9d8 Merge remote-tracking branch 'u-boot-ti/master' 2012-11-03 10:05:22 +01:00
Raphael Assenat
843a7ee8c4 eco5pk: Add new board and default config
Signed-off-by: Raphael Assenat <raph@8d.com>
[trini: Squash boards.cfg / MAINTAINERS change into main patch]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-30 15:28:06 -07:00
Pali Rohár
ed407be53e New board support: Nokia RX-51 aka N900
Based on previous work by: Alistair Buxton <a.j.buxton@gmail.com>

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Ивайло Димитров <freemangordon@abv.bg>
2012-10-30 15:28:06 -07:00
Lucas Stach
6bbda88384 tegra: add Colibri T20 board support
This adds board support for the Toradex Colibri T20 module.

Working functions:
- SD card boot
- USB boot
- Network
- NAND environment

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-29 09:07:04 -07:00
Wolfgang Denk
1b0757eced PPC: remove dead boards (AMX860, c2mon, ETX094, IAD210, LANTEC, SCM)
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years.  Get rid of the dead
weight.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
2012-10-28 20:17:25 +01:00
Stefano Babic
d81b27a245 MX35: add support for woodburn board
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.

The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash

In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:59 +02:00
Andrew Bradford
c3f8318f33 am335x_evm: Enable use of UART{1,2,3,4,5}
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.

Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2012-10-25 14:54:50 -07:00
Alison Wang
186fc4db26 ColdFire: Add Freescale MCF54418TWR ColdFire development board support
Add Freescale MCF54418TWR ColdFire development board support.

Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
2012-10-24 22:27:46 +08:00
Gerlando Falauto
c4d22de817 km83xx: add kmvect1 board
Add support for the new kmvect1 board powered by the mpc8309 processor.
As this board is very similar to the existing suvd3, instead of adding a
new config header file, just add a new config option to suvd3.h

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-10-23 15:23:26 -05:00
York Sun
ee52b188ca powerpc/t4qds: Add T4QDS board
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.

SERDES Connections
  32 lanes grouped into four 8-lane banks
  Two “front side” banks dedicated to Ethernet
  Two “back side” banks dedicated to other protocols
DDR Controllers
  Three independant 64-bit DDR3 controllers
  Supports rates up to 2133 MHz data-rate
  Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA

Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.

Detail information can be found in doc/README.t4qds

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 15:52:46 -05:00
Tom Rini
99070db0dc Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	drivers/serial/serial_lh7a40x.c

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19 18:23:38 -07:00
Paul Gortmaker
12c79a9578 powerpc: delete Wind River SBC8560/8540 support
The sbc8548/60 (both similar, just variations in UART hardware)
support has been removed from the linux kernel as of v3.6-rc1~132
so lets also now remove it from the u-boot tree as well.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-10-17 09:39:16 -07:00
Tom Rini
d1ff690612 Merge branch 'master' of git://git.denx.de/u-boot-mips 2012-10-17 08:57:13 -07:00
Stefan Roese
bfa5b71408 mpc82xx: Remove BMW board port
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-17 07:55:50 -07:00
Zhi-zhou Zhang
32afad783e MIPS: add board qemu-mips64 support
Both big-endian and little-endian are tested with below commands:
Rom version: (Default, Now we config it as rom version)
qemu-system-mips64el -M mips -bios u-boot.bin -cpu MIPS64R2-generic -nographic
qemu-system-mips64 -M mips -bios u-boot.bin -cpu MIPS64R2-generic -nographic
Ram version:
qemu-system-mips64el -M mips -cpu MIPS64R2-generic -kernel u-boot -nographic
qemu-system-mips64 -M mips -cpu MIPS64R2-generic -kernel u-boot -nographic

Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-10-16 15:02:08 +02:00
Łukasz Dałek
34cda7a0d8 h2200: Add support for iPAQ h2200 palmtop
Add basic support for HP iPAQ h2200 palmtop. h2200 palmtop was targeted
to general consumers. It has 64 MB of RAM, 32 MB flash. No intergrated
Wi-Fi nor Ethernet. Based on Intel PXA255 processor. It was shipped with
Windows CE 4.2 operating system.

Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
2012-10-16 07:14:55 +02:00
Fabio Estevam
7dd6545da7 mx6q: Add basic support for mx6qsabreauto
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input

Add very basic support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15 11:54:09 -07:00
Fabio Estevam
7891e258d4 mx6: Add basic support for mx6qsabresd board.
mx6qsabresd is a board based on mx6q SoC with the following features:
- 1GB of DDR3
- 1 USB OTG port
- 1 HDMI output port
- SPI NOR
- LVDS panel
- Gigabit Ethernet
- Camera Connector
- eMMC and SD card slot
- Audio

Add very basic support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15 11:54:08 -07:00
Fabio Estevam
af7ec0b058 mx6q: Factor out common DDR3 init code
Factor out common DDR3 initialization code, allowing easier maintainance of such
scripts.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-10-15 11:54:08 -07:00
Thierry Reding
66b796a560 tegra: Rename Medcom to Medcom-Wide
Medcom is the marketing name for an older, PXA-based version of the same
device. In order to avoid confusion, rename the Tegra-based version to
the new marketing name.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:06 -07:00
Stefan Roese
a821d08dca ppc4xx: Remove AP1000 board support
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-15 11:53:59 -07:00
Stefan Roese
dee9c534db ppc4xx: Remove ML2 board support
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-15 11:53:59 -07:00
Stefan Roese
99bcad1809 ppc4xx: Remove IOP480 support
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marex@denx.de>
2012-10-15 11:53:59 -07:00
Tom Rini
61c0d6ae77 gth2: Remove this platform
After taking with the former maintainer, delete this platform.  The
patch is from the former maintainer.

Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:46 -07:00
Wolfgang Denk
d923a5d59f MPC85xx: remove support for TQM85xx boards
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2).  As these boards have long
reached EOL it seems a waste of effort trying to fix them.  The vendor
has agreed to drop support for them, too.  So let's get rid of them.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
2012-10-05 11:07:42 -07:00
Dinh Nguyen
777544085d ARM: Add Altera SOCFPGA Cyclone5
Add minimal support for Altera's SOCFPGA Cyclone 5 hardware.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Tom Trini <trini@ti.com>
Cc: Wolfgang Denx <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
----
v8: Remove no_return attribute for reset_cpu

Based on v2012.10-rc2
2012-10-04 18:11:52 +02:00
Michal Simek
f22651cfc4 xilinx: Add new Zynq board
Add support for Xilinx Zynq board.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
CC: Joe Hershberger <joe.hershberger@gmail.com>
2012-10-04 16:57:36 +02:00
Stefan Roese
995b72ddda ARM: Add X600 board support (SPEAr600 based)
This patch adds support for the X600 SPEAr600 based board. Its also
the first SPEAr600 board that uses the newly introduced SPEAr600
SPL support. Xloader is not necessary any more. By using the new
"u-boot.spr" make target, one image will generated containing both,
U-Boot SPL (with mkimage header as needed by the SPEAr BootROM, and
the main U-Boot with mkimage header.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
2012-10-04 10:18:32 +02:00
Albert ARIBAUD
386c6cb10d Merge remote-tracking branch 'u-boot-marvell/master' 2012-10-03 16:44:29 +02:00
Luka Perkov
9b914727ce kirkwood: add support for Iomega iConnect board
Add support for new board iConnect from Iomega.

More information about the device can be found here:

http://go.iomega.com/en/products/network-storage-desktop/wireless-data-station/network-hard-drive-iconnect/?partner=4735

Signed-off-by: Luka Perkov <uboot@lukaperkov.net>
Tested-by: Wojciech Dubowik <wojciech.dubowik@neratec.com>
Tested-by: Tim Fletcher <tim@night-shade.org.uk>
2012-10-03 16:43:13 +05:30