Commit graph

370 commits

Author SHA1 Message Date
Timur Tabi
055ce08004 powerpc/85xx: remove support for the Freescale P3060
The P3060 was cancelled before it went into production, so there's no point
in supporting it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:53 -05:00
Liu Gang
461632bd71 powerpc/corenet_ds: Slave module for boot from PCIE
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.

Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.

NOTE: Because the slave can not erase, write master's NOR flash by
	  PCIE interface, so it can not modify the ENV parameters stored
	  in master's NOR flash using "saveenv" or other commands.

environment and requirement:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image is in master NOR flash.
	3. Put the slave's ucode and ENV into it's own memory space.
	4. Normally boot from local NOR flash.
	5. Configure PCIE system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to one PCIE interface by RCW.
	3. RCW should configure the SerDes, PCIE interfaces correctly.
	4. Must set all the cores in holdoff by RCW.
	5. Must be powered on before master's boot.

For the slave module, need to finish these processes:
	1. Set the boot location to one PCIE interface by RCW.
    2. Set a specific TLB entry for the boot process.
	3. Set a LAW entry with the TargetID of one PCIE for the boot.
	4. Set a specific TLB entry in order to fetch ucode and ENV from
	   master.
	5. Set a LAW entry with the TargetID one of the PCIE ports for
	   ucode and ENV.
	6. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIO_PCIE_BOOT_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
	1. Updated the README.srio-boot-corenet to add descriptions about
	   boot from PCIE, and change the name to
	   README.srio-pcie-boot-corenet.
	2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
	   "xxxx_SRIO_PCIE_BOOT", and the image builded with
	   "xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
	   from PCIE.
	3. Updated other macros and documents if needed to add information
	   about boot from PCIE.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:15 -05:00
Liu Gang
ff65f12699 powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build target
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:

		setenv bootmaster SRIO1
		saveenv

The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
	1. Reduce a build configuration item in boards.cfg file.
	   No longer need to build a special image for master, just use a
	   normal target image and set the "bootmaster" variable.
	2. No longer need to rebuild an image when change the SRIO port for
	   boot from SRIO, just set the corresponding value to "bootmaster"
	   based on the using SRIO port.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:14 -05:00
Jens Scharsig
eb0b43f264 rename EB+MCF-EV123 to its current marketing name EB+CPU5282
* rename board directory to eb_cpu5282
* rename EB+MCF-EV123_.*config to eb_cpu5282_.*config
* add Maintainer for EB+CPU5282 board
* rename prompt

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-08-09 23:07:32 +02:00
Allen Martin
d22650afab mkconfig: add support for SPL CPU
Add support for specifying a differnt CPU for main u-boot and SPL
u-boot builds.  This is done by adding an optional SPL CPU after the
main CPU in boards.cfg as follows:

     normal_cpu:spl_cpu

This this case CPU will be set to "normal_cpu" during the main u-boot
build and "spl_cpu" during the SPL build.

Signed-off-by: Allen Martin <amartin@nvidia.com>
2012-08-09 22:37:42 +02:00
Matthew McClintock
af2536088e powerpc/p1022ds: add support for SPI and SD boot
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.

Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.

Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:37 -05:00
Gerlando Falauto
b83cf848f0 powerpc/82xx: merge mgcoge.h and mgcoge3ne.h into km82xx.h
Since mgcoge and mgcoge3ne are the only km82xx boards, there is no need
to keep them as separate .h config files.
Therefore, make mgcoge3ne.h and mgcoge.h converge into a single km82xx.h
file.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31 22:36:23 +02:00
Thierry Reding
d70575b6d0 tegra: Add Tamonten Evaluation Carrier support
The Tamonten Evaluation Carrier is an evaluation board for the Tamonten
processor board. More information is available here:

	http://www.avionic-design.de/en/products/nvidia-tegra-tamonten-system-en/nvidia-tegra-tamonten-evboard-en.html

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-09 22:44:32 +02:00
Wolfgang Denk
50cd93b250 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
  ARM: cache: Move the cp15 CR register read before flushing the cache.
  ARM: introduce arch_early_init_r()
  PXA: Enable CONFIG_PREBOOT on zipitz2
  ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
  No need to define CONFIG_ARCH_CPU_INIT.
  add new board vl_ma2sc
  MTD: SPEAr SMI: Add write support for length < 4 bytes
  i2c: designware_i2c.c: Add support for the "i2c probe" command
  rtc/m41t62: Add support for M41T82 with HT (Halt Update)
  SPL: ARM: spear: Add SPL support for SPEAr600 platform
  Makefile: Add u-boot.spr build target (SPEAr)
  SPL: ARM: spear: Remove some objects from SPL build
  SPL: lib/Makefile: Add crc32.c to SPL build
  SPL: common/Makefile: Add image.c to SPL build
  arm: Don't use printf() in SPL builds
  GPIO: Add SPEAr GPIO driver
  net: Multiple updates/enhancements to designware.c
  cleanup/SPEAr: Define configuration flags more elegantly
  cleanup/SPEAr: Remove unnecessary parenthesis
  SPEAr: Correct SoC ID offset in misc configuration space
  SPEAr: explicitly select clk src for UART
  SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
  SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
  SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
  SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
  SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
  SPEAr: Enable dcache for fast file transfer
  SPEAr: Enable autoneg for ethernet
  SPEAr: Enable udc and usb-console support only for usbtty configuration
  SPEAr: Enable usb device high speed support
  SPEAr: Initialize SNOR in early_board_init_f
  SPEAr: Change the default environment variables
  SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
  SPEAr: Add configuration options for spear3xx and spear6xx boards
  SPEAr: Add basic arch related support for SPEAr SoCs
  SPEAr: Add interface information in initialization
  SPEAr: Add macb driver support for spear310 and spear320
  SPEAr: Configure network support for spear SoCs
  SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
  SPEAr: Eliminate dependency on Xloader table
  SPEAr: Fix ARM relocation support
  st_smi: Fixed page size for Winbond W25Q128FV flash
  st_smi: Change timeout loop implementation
  st_smi: Fix bug in flash_print_info()
  st_smi: Change the flash probing method
  st_smi: Removed no needed dependency on ST_M25Pxx_ID
  st_smi: Fix smi read status
  st_smi: Move status register read before modifying ctrl register
  st_smi: Read status until timeout happens
  st_smi: Enhance the error handling
  st_smi: Change SMI timeout values
  st_smi: Return error in case TFF is not set
  st_smi: Add support for SPEAr SMI driver
  mtd/NAND: Remove obsolete SPEAr specific NAND drivers
  SPEAr: Configure FSMC driver for NAND interface
  mtd/NAND: Add FSMC driver support
  arm/km: remove calls to kw_gpio_* in board_early_init_f
  arm/km: add implementation for read_dip_switch
  arm/km: support the 2 PCIe fpga resets
  arm/km: skip FPGA config when already configured
  arm/km: redefine piggy 4 reg names to avoid conflicts
  arm/km: cleanup km_kirkwood boards
  arm/km: enable BOCO2 FPGA download support
  arm/km: remove portl2.h and use km_kirkwood instead
  arm/km: convert mgcoge3un target to km_kirkwood
  arm/km: add kmcoge5un board support
  arm/km: add kmnusa board support
  arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
  cm-t35: fix incorrect NAND_ECC layout selection
  ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
  ARM: OMAP4/5: Move USB pads to essential list.
  ARM: OMAP4/5: Move USB clocks to essential group.
  ARM: OMAP4/5: Move gpmc clocks to essential group.
  ARM: OMAP4+: Move external phy initialisations to arch specific place.
  omap4: Use a smaller M,N couple for IVA DPLL
  da850/omap-l138: Enable auto negotiation in RMII mode
  omap: am33xx: accomodate input clocks other than 24 Mhz
  omap: emif: fix bug in manufacturer code test
  omap: emif: deal with rams that return duplicate mr data on all byte lanes
  OMAP4+: Force DDR in self-refresh after warm reset
  OMAP4+: Handle sdram init after warm reset
  ARM: OMAP3+: Detect reset type
  arm: bugfix: Move vector table before jumping relocated code
  Kirkwood: Add support for Ka-Ro TK71
  arm/km: use spi claim bus to switch between SPI and NAND
  arm/kirkwood: protect the ENV_SPI #defines
  ARM: don't probe PHY address for LaCie boards
  lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
  lacie_kw: fix SDRAM banks number for net2big_v2
  Kirkwood: add lschlv2 and lsxhl board support
  net: add helper to generate random mac address
  net: use common rand()/srand() functions
  lib: add rand() function
  kwboot: boot kirkwood SoCs over a serial link
  kw_spi: add weak functions board_spi_claim/release_bus
  kw_spi: support spi_claim/release_bus functions
  kw_spi: backup and reset the MPP of the chosen CS pin
  kirkwood: fix calls to kirkwood_mpp_conf
  kirkwood: add save functionality kirkwood_mpp_conf function
  km_arm: use filesize for erase in update command
  arm/km: enable mii cmd
  arm/km: remove CONFIG_RESET_PHY_R
  arm/km: change maintainer for mgcoge3un
  arm/km: fix wrong comment in SDRAM config for mgcoge3un
  arm/km: use ARRAY_SIZE macro
  arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
  arm/km: add piggy mac adress offset for mgcoge3un
  arm/km: add board type to boards.cfg
  AT91SAM9*: Change kernel address in dataflash to match u-boot's size
  ATMEL/PIO: Enable new feature of PIO on Atmel device
  ehci-atmel: fix compiler warning
  AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
  Atmel : usb : add EHCI driver for Atmel SoC
  Fix: AT91SAM9263 nor flash usage
  Fix: broken boot message at serial line on AT91SAM9263-EK board
  i.MX6 USDHC: Use the ESDHC clock
  mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
  i.MX28: Add function to adjust memory parameters
  mx28evk: Fix PSWITCH key position
  mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
  mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
  imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove unused CONFIG_MII_GASKET
  mx6: Avoid writing to read-only bits in imximage.cfg
  m28evk: use same notation to alloc the 128kB stack
  ...

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-08 19:26:33 +02:00
esw@bus-elektronik.de
4324c75fcc add new board vl_ma2sc
* add support for board VL+MA2SC
* adds vl_ma2sc_config for standard NOR boot configuration
* adds vl_ma2sc_ram_config for RAM load configuration

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
2012-07-07 14:07:44 +02:00
Vipin KUMAR
f273e5b2a6 SPEAr: Add configuration options for spear3xx and spear6xx boards
This patch adds options for all the below mentioned configurations and
subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h,
spear6xx_evb.h etc to depict evaluation board configuration.

SPEAr3xx and SPEAr6xx boards can be compiled in following configurations
1. Environment placed in NAND
2. Console on usb device
3. Console on usb device with environment placed in NAND
4. SPEAr310 and SPEAr320 support environment variables in parallel
NOR flash.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-07-07 14:07:40 +02:00
Holger Brunck
48ced62cfb arm/km: cleanup km_kirkwood boards
Remove config options from boards.cfg and simply add one switch
per board and differ afterwards in km_kirkwood.h between the features.
More boards are upcoming and therefore it's easier to have this
at one place.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Valentin Longchamp
b37f772433 arm/km: enable BOCO2 FPGA download support
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.

This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
   for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
   the CPU can update the FPGA configuration when the kernel is running

The boards with a PCIe FPGA but without BOCO2 still are supported.

The config option name is CONFIG_KM_FPGA_CONFIG

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
6ef6486180 arm/km: remove portl2.h and use km_kirkwood instead
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
f945439af9 arm/km: convert mgcoge3un target to km_kirkwood
Use the generic header km_kirkwood.h and get rid of the
board specific header.

changes for v2: rebased because of changes in other patches

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:37 +02:00
Holger Brunck
d9354530fe arm/km: add kmcoge5un board support
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween, this needs a new configuration for the mvgbe driver.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:36 +02:00
Holger Brunck
8170aefc84 arm/km: add kmnusa board support
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.

Some other details:
 - IVM EEPROM is at adress: pca9547:70:9
 - PCI is enabled
 - PIGGY4 is connected via MV88E6352 simple switch. There is no phy
   between the simple switch and the kirkwood.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:36 +02:00
Marek Vasut
0ec005fe00 Kirkwood: Add support for Ka-Ro TK71
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Wolfgang Denk <wd@denx.de>
2012-07-07 14:07:33 +02:00
Michael Walle
f214a20e7e Kirkwood: add lschlv2 and lsxhl board support
This patch adds support for both the Linkstation Live (LS-CHLv2) and
Linkstation Pro (LS-XHL) by Buffalo.

Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:32 +02:00
Holger Brunck
e29c6d0401 arm/km: add board type to boards.cfg
Some other kirkwood boards from keymile will follow. They will have some
small differences, but we want to use the km_kirkwood.h for all to
distinguish them. This patch a preparation for this.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2012-07-07 14:07:30 +02:00
Stephen Warren
39e3711839 tegra: Compulab TrimSlice board support
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
d5ebc937c9 tegra: Whistler board support
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:

E1120 motherboard
E1108 CPU board
E1116 PMU board

The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.

Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:17 +02:00
Prabhakar Kushwaha
7530d341c7 powerpc/mpc85xx:Add BSC9131 RDB Support
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. BSC9131 SOC
 is an integrated device that targets Femto base station market. It combines
 Power Architecture e500v2 and DSP StarCore SC3850 core technologies with
 MAPLE-B2F baseband acceleration processing elements

  BSC9131RDB Overview
   -----------------
     -1Gbyte DDR3 (on board DDR)
     -128Mbyte 2K page size NAND Flash
     -256 Kbit M24256 I2C EEPROM
     -128 Mbit SPI Flash memory
     -USB-ULPI
     -eTSEC1: Connected to RGMII PHY
     -eTSEC2: Connected to RGMII PHY
     -DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.

This patch adds support for mainly Power side functionalities and peripherals

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:29 -05:00
Holger Brunck
0f2b721c80 powerpc/83xx: add kmcoge5ne board support
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.

Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:40 -05:00
Holger Brunck
7f4bd9a686 powerpc/83xx/km: use tuxx1.h for kmsupx5 target
This additional header is unneeded, we can use the tuxx1.h for this
target.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 16:42:32 -05:00
Phil Edworthy
99744b7e34 sh: Add SH7269 device and RSK2+SH7269 board
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.

The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:54 +09:00
Nobuhiro Iwamatsu
bfc93fb47d sh: Add support for AP-SH4A-4A board
The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
  - 64MB DDR2-SDRAM
  - 16MB NOR Flash memory
  - Serial console (SCIF)
  - Ethernet (SH-Ether with Gigabit)
  - I2C

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:54 +09:00
Nobuhiro Iwamatsu
8ca805e102 sh: Add support for r0p7734 board
The r0p7734 board has SH7734, 128MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
- 128MB DDR2-SDRAM
- 32MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether/SMSC)

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:53 +09:00
Stefano Babic
79656d27b3 MX53: Add support to ESG ima3 board
The ESG ima3-mx53 board is based on the Freescale
i.MX53 SOC. It boots from NOR (128 MB) and
supports Ethernet (FEC), SATA.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:31 +02:00
Enric Balletbò i Serra
dc7a9e64bf OMAP3: igep00x0: Reduce lines of code for IGEP-based boards.
This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.

On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.

More than 200 duplicated lines have been deleted.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2012-05-15 08:31:23 +02:00
David Purdy
1d0f5fa11d kirkwood: add support for Cloud Engines Pogoplug E02
This patch adds support for Cloud Engines Pogoplug E02

Information regarding the CE Pogoplug E02 board can be found at:
http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray

Signed-off-by: Dave Purdy <david.c.purdy@gmail.com>
Cc: prafulla@marvell.com
Cc: albert.u.boot@aribaud.net
2012-05-15 08:31:22 +02:00
Luka Perkov
e5841e1211 kirkwood: add NAS62x0 board support
Add support for new boards RaidSonic ICY BOX NAS6210 and NAS6220.

NAS6210 has 1 SATA and 1 eSATA port while NAS6220 has 2 SATA ports.

More information about the boards can be found here:

http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7036
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7515

Signed-off-by: Luka Perkov <uboot@lukaperkov.net>
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
2012-05-15 08:31:22 +02:00
Vladimir Zapolskiy
463ec1caa3 devkit3250: add Timll DevKit3250 board initial support
This change adds a basic support for Embest/Timll DevKit3250 board,
NOR and UART are the only supported peripherals for a moment. The board
doesn't require low-level init, because the initial SDRAM and GPIO
configuration is performed during kickstart bootloader execution.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15 08:31:22 +02:00
Wolfgang Denk
4212657c53 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
  powerpc/ppc4xx: Remove typedefs for gdsys FPGA
  powerpc/ppc4xx: Fix typo in gdsys_fpga.h
  powerpc/ppc4xx: Update gdsys board configurations
  powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
  powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
  powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
  powerpc/ppc4xx: Adjust environment size on neo
2012-04-30 16:55:25 +02:00
Wolfgang Denk
5f6db68b42 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
  powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
  cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
  PowerPC: correct the SATA for p1/p2 rdb-pc platform
  powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
  powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
  powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
  powerpc/corenet_ds: Slave module for boot from SRIO
  powerpc/corenet_ds: Master module for boot from SRIO
  powerpc/corenet_ds: Document for the boot from SRIO
  powerpc/corenet_ds: Correct the compilation errors about ENV
  powerpc/srio: Rewrite the struct ccsr_rio
  powerpc/85xx:Fix lds for nand boot debug info
  powerpc/p2041rdb: add env in NAND support
  powerpc/p2041rdb: add NAND and NAND boot support
  powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
  powerpc/85xx:Avoid vector table compilation for nand_spl
  powerpc/85xx:Fix IVORs addr after vector table relocation
  powerpc/85xx:Avoid hardcoded vector address for IVORs
  powerpc/p1023rds: Disable nor flash node and enable nand flash node
2012-04-30 16:45:56 +02:00
Dirk Eibach
6e9e6c36a6 powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
In order to add boards that have different hardware for fpga reset,
any 405ep gdsys board now provides these functions:

void gd405ep_init(void);
void gd405ep_set_fpga_reset(unsigned state);
void gd405ep_setup_hw(void);
int gd405ep_get_fpga_done(unsigned fpga);

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30 15:00:56 +02:00
Liu Gang
292dc6c501 powerpc/corenet_ds: Slave module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.
	5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode
	   locally.

For the slave module, need to finish these processes:
	1. Set the boot location to SRIO1 or SRIO2 by RCW.
    2. Set a specific TLB entry for the boot process.
	3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot.
	4. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_SLAVE_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
5ffa88eca7 powerpc/corenet_ds: Master module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.

For the master module, need to finish these processes:
	1. Initialize the SRIO port and address space.
	2. Set inbound SRIO windows covered slave's u-boot image stored in
	   master's NOR flash.
	3. Master's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_MASTER_config
	4. Master must boot first, and then slave can be powered on.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:32 -05:00
Shaohui Xie
c9b2feafaa powerpc/p2041rdb: add NAND and NAND boot support
New P2041RDB board will add a NAND chip, so add support for NAND and
NAND boot.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:31 -05:00
Macpaul Lin
b9725ae3f3 board/adp-ag102: add configuration of adp-ag102
board:
Add config file of board adp-ag102
Add adp-ag102 into boards.cfg
Add adp-ag102 into MAINTAINERS

doc:
add README of ag102

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22 16:58:23 +08:00
Daniel Schwierzeck
6cb461b4f1 MIPS: fix endianess handling
Make endianess of target CPU configurable. Use the new config
option for dbau1550_el and pb1000 boards.

Adapt linking of standalone applications to pass through
endianess options to LD.

Build tested with:
 - ELDK 4 mips_4KC- and mips4KCle
 - Sourcery CodeBench Lite 2011.03-93

With this patch all 26 MIPS boards can be compiled now in one step by
running "MAKEALL -a mips".

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-04-02 15:54:53 +02:00
Tom Rini
76e2c169a5 OMAP: Remove omap1610inn-based boards
The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-03-29 08:19:29 +02:00
Marek Vasut
2152df67c3 IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
2012-03-26 23:09:26 +02:00
prabhakar.csengg@gmail.com
fda9c20c80 dm6467Tevm: Use a common configuration file for davinci_dm6467evm and davinci_dm6467Tevm
In commit 2d575e4685 a separate header
file was introduced for the DM6467T EVM, include/configs/davinci_dm6467Tevm.h.
The substantial difference between the davinci_dm6467evm and the
davinci_dm6467Tevm configuration is a single bit in the hardware revision
that is passed to the Linux kernel and davinci_dm6467evm has
REFCLK_FREQ = 27000000 where as davinci_dm6467Tevm.h has a
REFCLK_FREQ = 33000000.

This patch removes include/configs/davinci_dm6467Tevm.h. Instead the
include/configs/davinci_dm6467evm.h configuration is used for DM6467T EVMs and
renamed CFG_REFCLK_FREQ to CONFIG_REFCLK_FREQ and CONFIG_REFCLK_FREQ is defined
in boards.cfg.

Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Tom Rini <trini@ti.com>
2012-02-27 21:19:24 +01:00
Hadli, Manjunath
206a1038f7 da850evm: read mac address from I2C EEPROM on AM18x EVM
add support to read mac address for AM18x EVM manufactured from
Spectrum digital which have mac address stored in I2C EEPROM manufactured
by WINBOND. This patch reads mac address from I2C EEPROM and sets the
environment variable if not set, If mac address is already present in
environment compare it with the mac address in EEPROM and warn on
mismatch.Introduced a config option CONFIG_MAC_ADDR_IN_EEPROM to where
to look for the mac address.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
2012-02-27 21:19:24 +01:00
Hadli, Manjunath
38fed6ee95 da850evm: add support to read mac address from SPI flash
add support to read mac address for da850/L138 evm manufactured by
Logic PD which store mac address in SPI flash manufactured by ST
Microelectronics. This patch adds support to read mac address from
SPI flash and set the mac address if it hasn't been set in environment,
If it has been set in the environment it compares the value one with
SPI flash and warns on mismatch. Introduced a config option
CONFIG_MAC_ADDR_IN_SPIFLASH indicating where to look mac address for.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
2012-02-27 21:19:24 +01:00
Wolfgang Denk
06576b2efc Merge branch 'master' of git://git.denx.de/u-boot-blackfin
* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: pata_bfin: fix printf warning
  Blackfin: bfin_nand: mark local func static
  linkage.h: move from blackfin to common includes
  Blackfin: br4: new board port
  Blackfin: add in/out le32 variants
  post: add blackfin to the post_time_ms list
  Blackfin: bf537-stamp: drop board reset workaround
  Blackfin: pr1: new board port
2012-02-13 23:13:22 +01:00
Dimitar Penev
051a5f30f1 Blackfin: br4: new board port
This adds support for the BR4 Appliance.  It is a quad channel ISDN BRI
board based on Blackfin BF537 CPU.

Signed-off-by: Dimitar Penev <dpn@switchfin.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12 15:03:25 -05:00
Dimitar Penev
939b150ae5 Blackfin: pr1: new board port
This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX.
This board is Blackfin BF537 based.  The schematics are not fully opened.

Signed-off-by: Dimitar Penev <dpn@switchfin.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12 15:03:25 -05:00
Christian Riesch
9a3aae22ed arm, davinci: Add support for the Calimain board from OMICRON electronics
This patch adds support for the Calimain board from
OMICRON electronics GmbH. The board features a Texas Instruments AM1808
SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and
CS3.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12 10:11:33 +01:00