We do not have a root partition in spi flash any more.
Adapt comment.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current iocsr-config-cyclone5.c is actually board specific, although the
file name suggests otherwise.
As the file was generated for the SoCkit, move it there and add a new one
for the socrates.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Distil common code pattern for Phytec entry functions into a macro and
use it instead. This way a new board derivateve that differs only in device
tree file can be added with just one line.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Distil different startup functions into a generic one, different
behavioral aspects of which can be influenced by its parameters.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some drivers need clk_set_rate. To be able to link with these
drivers enabled provide a clk_set_rate stub.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPU_ARM946E is selected by boards, so letting it depend on !MMU
leads to broken dependencies. Let MMU depend on !CPU_ARM946E instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Don't try to attach mac to device if there is no net support selected.
Fixes:
undefined reference to `dev_add_param_mac' in both iim and ocotp drivers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable support for the i.MX6sx sabresdb and the KaRo Tx6x.
The sabresdb needs regulator support, so enable this aswell.
Also enable usbserial support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Freescale i.MX6sx sabresdb board.
Tested are:
- UART
- The three SD card slots
- USB host
- USB otg (host and device mode)
- FEC (both)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add some cpu type defines and clock support. The clock support
is very different from other i.MX variants, so it's a separate
file, like done in the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current algorithm assumes the MAC address starts at a 4 byte
aligned address. Unfortunately this is not always the case. On the
i.MX6sx the MAC Address for the second FEC starts at offset 0x632.
The register space for the fuse map has holes, only the 16 byte
aligned words contain data. This means we have to skip the holes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Pin 0x74 (gpmc_wpn.gpio0_30) is not used on the phyCORE SOM.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Blspec is a consumer of the flexible bootargs mechanism, so it should
depend on it rather than select it.
Fixes:
warning: (BLSPEC && DEFAULT_ENVIRONMENT_GENERIC_NEW) selects FLEXIBLE_BOOTARGS
which has unmet direct dependencies (COMMAND_SUPPORT && CMD_GLOBAL)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Avoids a build failure if the config does not include ULPI support.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes NAND initialization issue which appears occasionally on
some i.MX6 SoCs (particulary was observed on phyCARD-i.MX6 with
i.MX6Solo).
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are only a few users of BUILTIN_DTB left, but those should
alsways fill thr name properly. Avoids lots of failures in the
randconfig builds.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It doesn't make sense to allow building in a single DTB into a
multiimage barebox, so we can spare the user this option.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This was only done for some of the boards and while it is ok to build
those boards without regulator support it may potentially yield non-working
barebox binaries. This is clearly not what the user wanted.
Also select the appropriate bus support needed for the MC13xxx.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Old version of imx6_mmdc_add_mem did not use 64-bit arithmetic and
thus was prone to overflow on systems with 4GB of memory. It also did
not take into account the fact that i.MX6 does not support more than
3.8GB of memory and would report incorrect memory size. This commit
fixes both issues.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Teresa Gámez
Steffen Trumtrar
Christian Hemp
Andrey Smirnov
Lucas Stach
Wadim Egorov
Dmitry Lavnikevich