The nand controller on i.MX51/53 uses two base addresses. Instead
of hardcode the second address use the new shiny resources two specify
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on the Linux driver. Tested with m25p80 with CS in GPIO mode.
Clock setting support is ad-hoc as the corresponding mach is not using
the generic clock infrastructure.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
and busnum start at 1
as this
Bus 001 Device 002: ID 0b95:7720 AX88772
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This code was tested barely with m25p80 driver, reading jedec id and some data
from the chip worked fine.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some NOR flash chips have commands with length greater than the maximum
value size of uchar.
Based on an U-Boot Patch by Vasiliy Leoenenko <vasiliy.leonenko@mail.ru>
Only tested with little endian on an intel cfi_flash.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the m25p80 driver. It has been ported from
Linux. MTD code has been removed. It has been tested with
a m25p40 chip and the Altera SPI master driver.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Files associated to a device showed up in a long list. Instead,
print them in seperate lines and also show offset/size information
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise, when a non active device is unregistered, we call
list_del on an unitialized list which oopses.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will also fix the clock support as we now switch to allocated generic
device
as we can need to associate the clock and the device but the driver is probe
before the association
we also change the atmel serial name to "atmel_usart" to simplify sharing with
linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as now all the drivers and board have been switch to resource whe can drop
map_base and size from device_d
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
use generic read/write depending on the memory size
if no reg_read/write defined
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
pass the hccr and hcor register base via resource
instroduce add_generic_usb_echi_device with hccr = base + 0x100 and
hcor = base + 0x140
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
