Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because CPU frequency setup called after power initialization,
this call now is not necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
FIXME: part of or no data is written. File copy ends
with message: "atmel_mci@atmel_mci0: command/data timeout"
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- change the kernel and rootfs locations
- correct the NAND mtd partitions
- fix the DDR RAM location(so BareBox load address)
- expect the root file system type to be UBIFS
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
What looked like a TO specific hack really is a hack for
older babbage boards. As the babbage code now handles this
correctly we can remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The imx51 lowlevel setup code currently sets the full cpu
speed only for TO3. It turned out that this is not a TO
specific hack but a hack for older babbage boards. Move
the lowlevel init after babbage_power_init() so that we
can remove the hack from the generic i.MX51 lowlevel
function. As this potentially changes the UART clock we
have to flush the console beforehand and call the clock
notifier afterwards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The previous code assumed pll2 which is correct when we set the
uart parent to pll2 beforehand. The reset default is different
though, so calculate uart parent based on hardware setting.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image sizes have been hardcoded to 256K. This is inefficient
for smaller images and nonfunctional for bigger images. Calculate
the image size during compile time and use it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox_image_size was calculated wrong when PRE_IMAGE is defined.
In this case _text does not refer to the binary image start. We
have to use TEXT_BASE here.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
when compiling for a imx53 with i2c enabled i got the following error:
drivers/built-in.o: In function `i2c_imx_set_clk':
/home/ggebhardt/repos/ecuv6_bl/barebox/drivers/i2c/busses/i2c-imx.c:282:
undefined reference to `imx_get_i2cclk'
make[4]: *** [.tmp_barebox1] Error 1
make[3]: *** [CMakeFiles/bootloader] Error 2
make[2]: *** [CMakeFiles/bootloader.dir/all] Error 2
make[1]: *** [CMakeFiles/bootloader.dir/rule] Error 2
make: *** [bootloader] Error 2
I copied the following from the corresponding imx51 implementation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When CONFIG_DEFAULT_ENVIRONMENT_GENERIC is set the Make system
will automatically compile in defaultenv/ into the environment. Some
boards explicitely add this path again in their defconfig which is
not needed. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx27_add_mmc0 really registered SDHC2. Fix this by adding a
imx27_add_mmc1 and use this in the pca100 board file. Also add
imx27_add_mmc2 helper for register SDHC3.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove GPIO2.6 setup from lowlevel_init. It can be defined in board
initialization code if it necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reduce the size of the MLO we have to activate thumb-2 support.
Otherwise the board will not boot.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a OMAP4 specific GMPC nand config for pcm049 and phyCARD-A-XL2 to increase
performance. Also add the possiblility to pass a board GPMC nand config.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop kernelimage_type bootm now boots all of them.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- use tslf
- bootm: enable oftree and uimage support
- enable mmu support
- drop cfi support (no nor on the board)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
update fancy prompt to be the same as the other Atmel board
use the same feature on 9g10ek and 9261ek
- use tlsf
- enable MMU
- set max size to 256KiB
- bootm: add initrd support
- nand: drop non used hw ecc and oob device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- set max size to 256KiB
- enable MMU
- bootm: enable oftree and initrd support
- nand: drop non used hw ecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
most of the board does not have a nor soldered
update the nand partition table to boot from nand with bootstrap
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Alexander Shiyan
Sascha Hauer
Asen Chavdarov Dimov
guenter.gebhardt@rafi.de
Jean-Christophe PLAGNIOL-VILLARD
Teresa Gámez
Jan Weitzel
Michael Grzeschik