This adds host tools for i.MX to generate the i.MX internal
flash header format and a tool to upload these images to an
i.MX SoC via USB.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We had pbl_cc__o_c instead of pbl_cc_o_c. This caused all pbl object
files to be rebuilt everytime due to missing .cmd file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on the same Linux commit from Stephen Warren:
commit b40b25fff8205dd18124d8fc87b2c9c57f269b5f
Author: Stephen Warren <swarren@nvidia.com>
Date: Wed Mar 6 10:58:37 2013 -0700
kbuild: always run gcc -E on *.dts, remove cmd_dtc_cpp
Replace cmd_dtc with cmd_dtc_cpp, and delete the latter.
Previously, a special file extension (.dtsp) was required to trigger
the C pre-processor to run on device tree files. This was ugly. Now that
previous changes have enhanced cmd_dtc_cpp to collect dependency
information from both gcc -E and dtc, we can transparently run the pre-
processor on all device tree files, irrespective of whether they
use /include/ or #include syntax to include *.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This brings us the following which we need for dtb file generation.
commit 2ab8a99661f4ce052bbad064237c441371df8751
Author: Stephen Warren <swarren@nvidia.com>
Date: Wed Mar 6 10:27:45 2013 -0700
kbuild: fixdep: support concatenated dep files
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The v0 header, used on Kirkwood, has some fields to indicate the type
of the NAND ECC, and the page size of the NAND. This commit adds
support for such fields, which are needed to support the Kirkwood
Guruplug platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The function image_boot_mode_id() converts the name of a boot media
into the corresponding Marvell specific code. However, 0 that we
currently used to indicate that the boot media name wasn't found,
could potentially be a valid value. So instead we use -1 to indicate a
failure.
This is also done in preparation to the introduction of
image_nand_ecc_mode_id(), which will convert a NAND ECC mode name into
the corresponding identifier. And in this case 0 is a valid identifier
of a NAND ECC mode, so we cannot use it to indicate a failure. Since
we want image_boot_mode_id() and image_nand_ecc_mode_id() to have a
consistent behavior, we change the former in this commit. The latter
is introduced in the next commit.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We now assume that at most one binary header can be added, so we no
longer need to loop for all configuration options to find the binary
blobs. We simply find the binary blob configuration option in
'binarye' and use that when we need to generate the corresponding
header.
Also, just like we did for the v0 image creation, use
image_find_option() to find the value of the different options needed
to create the main header.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Until now, the v0 image creation function was expecting the
configuration parameters to be ordered with first the configuration
parameters affecting the main header, then the DATA configuration
parameters that affect the extended header, then the payload.
However, with the recently added ability to override the destination
address or execution address, the configuration options corresponding
to those values may now appear at the end of the configuration
options. This commit allows to handle that by making the image
creation more flexible:
- The configuration options for the main header are just searched
amongst all options, the first match is used.
- When building the extension header with the DATA options, all DATA
options from the configuration file are used, in the order in which
they appear in the kwbimage.cfg file.
This will for example allow a kwbimage.cfg for a v0 image to not
specify any destination or execution address, and simply override it
from the command line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit uses the newly introduced image_count_options() function
to:
- See if there is any DATA option that require the creation of an
extended header for v0 header.
- Verify that no more than one payload has been provided when
creating a v0 header.
- Verify that no more than one binary payload has been provided when
creating a v1 header. Technically speaking, it is possible to
support several payloads, but in real life, only one gets used, so
we will only support that to make the code simpler for now. It can
always be extended later on if needed.
- Verify that no more than one payload has been provided when
creating a v1 header.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This function returns the number of configuration elements that match
a given type. Will be used to do some sanity checking of the number of
options.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Marvell Dove SoC also has an UART bootmode to upload payload after
powerup. In contrast to Kirkwood and Armada 370/XP, Dove does not
respond to a special sequence sent on UART0 but requires to be
booted into UART bootmode by bootstraps. This is usually done by
pressing a push button that will set bootstraps accordingly.
This patch adds a new option, documentation and corresponding prompts
to support the above requirements. Also a left-over option ('-p')
is removed.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds some references to Marvell Dove as it is also supported by
kwbimage.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This tool is used with Marvell EBU SoC to trigger the UART boot mode
provided by the SoC BootROM, and push the bootloader image to the
target using the Xmodem protocol.
It has been taken from the U-Boot source code, with minor
modifications to make it work with Armada 370/XP platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Marvell EBU SoCs (Kirkwood, Armada 370, Armada XP) have a BootROM
that understand a specific image format, composed of a main header,
several extension headers and a paylod. This image can be booted from
NAND, SPI, SATA, UART, NOR, etc.
This patch adds a tool that allows to extract the components and
configuration of existing images, and to create new images.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The checkpatch.pl script is also used to validate user-space code in
the scripts/ directory, so it should allow printf() lines to be longer
than 80 columns.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The bootrom only reads an image if the correct checksum is present in the
header. The calculation is pretty simple:
sum over all words from 0x20 to 0x44
Two of this words are the image length. That is why the checksum can not be
calculated until barebox_image_size is known.
The easiest solution is a program that has to be run after make.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add rules to generate dtb files from dts/dtsi files,
optionally run the source files through the preprocessor.
Also add a rule to generate object files to include in
the barbox binary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This syncs the localversion generation with the kernel.
At least one effect is that a barebox built from a tar archive no
longer marks itself as dirty. Also it moves some stuff from a scary
Makefile to a not-so-scary shell script.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In case environment loading/saving failed, the calling program
should be informed about that by returning a non zero exit code.
Signed-off-by: Christian Kapeller <christian.kapeller@cmotion.eu>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
From previous patch that replaced printf with puts:
puts adds it's own line ending, so do not append it manually
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The lowlevel code is expected to be present only ONCE
in PBL is enabled otherwise in barebox
This fix the module support with PBL and allow to reduce the size of barebox
by drop the lowlevell init in barebox as the compiler does not discard it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use puts() because printf() isn't necessary,
to fix the following compiler warnings:
/barebox/common/menu.c: In function ‘menu_show’:
/barebox/common/menu.c:277:4: warning: format not a string literal and no format arguments [-Wformat-security]
/barebox/scripts/omap4_usbboot.c: In function ‘read_asic_id’:
/barebox/scripts/omap4_usbboot.c:101:3: warning: format not a string literal and no format arguments [-Wformat-security]
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Vicente <vicencb@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
include/environment.h is no longer necessary to build scripts/bareboxenv,
so remove its inclusion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can use to check pbl
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When obj-y has foo/bar.o, kbuild can't generate
foo/bar.o according foo/bar.c. Fix this
this patch based on linux kernel
commit 521cb40b0c44418a4fd36dc633f575813d59a43d
Signed-off-by: 张忠山 <zzs213@126.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This implements two new options for the loadenv command:
-s: removes (scrubs) old directory contents to be able to
create a fresh environment from for example /dev/defaultenv
-n: no overwrite. Do not overwrite existing files. This allows
to keep parts of the old environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the utility outputs the image on stdout we have to print the
error messages to stderr in order to see them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The omap spi utility requires the image size to be a multiple of four
bytes. This seems unnecessary, we can just pad with a few bytes to
get the required alignment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Thomas Petazzoni
Sebastian Hesselbarth
Lucas Stach
Steffen Trumtrar
Christian Kapeller
Vicente Bergas
Jean-Christophe PLAGNIOL-VILLARD
Fabio Porcedda
张忠山
Antony Pavlov
Robert P. J. Day