imx27_add_mmc0 really registered SDHC2. Fix this by adding a
imx27_add_mmc1 and use this in the pca100 board file. Also add
imx27_add_mmc2 helper for register SDHC3.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a OMAP4 specific GMPC nand config for pcm049 and phyCARD-A-XL2 to increase
performance. Also add the possiblility to pass a board GPMC nand config.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop kernelimage_type bootm now boots all of them.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
update fancy prompt to be the same as the other Atmel board
use the same feature on 9g10ek and 9261ek
- use tlsf
- enable MMU
- set max size to 256KiB
- bootm: add initrd support
- nand: drop non used hw ecc and oob device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
most of the board does not have a nor soldered
update the nand partition table to boot from nand with bootstrap
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add Mitac MioA701 board initial support.
The support provides basic boot and :
- a console over USB (serial gadget).
- the SD card support
- the MTD docg3 support
- the LCD support
Add a check in the default environment for a barebox.env
file on the first partition (FAT). If the file exists,
source it instead of the normal boot procedure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Traditionally U-Boot and barebox have the exception vectors at
the start of the binary. There is no real reason in doing so,
because in the majority of cases this data will not be at 0x0
where it could be used as vectors directly anyway.
This patch puts the vectors into a separate linker section and
defines an head function which is placed at the start of the
image instead. Putting this in a separate function also has
the advantage that it can be placed at the start of images
which require an additional header like several Freescale i.MX
images. As the head function contains the barebox arm magic
those images can now also be detected as barebox images.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- this is taken from freescale-mx35-3-stack/3stack.c and allows
this board to run Freescale's kernel which relies on the system
revision to configure the correct PMIC.
- On rev0 boards (with DA9053), the log is :
detected i.MX53 rev 2.1
MCIMX53-START board 1.0
On newer boards (rev A or B with MC34708), the log is :
mc34708-i2c@mc34708-i2c0: MC34708 ID: 0x0014
detected i.MX53 rev 2.1
MCIMX53-START-R board 1.0 rev B
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
and register mc34708 which is present on MCIMX53-START-R board
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some variants of the i.MX53 do not allow to run at 1GHz, so
pass a cpu frequency parameter to the lowlevel init function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise the kernel would not register the nand partitions.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Extend DCD table and low level init routines. Add barebox SDRAM
device. Also, fix the memory size for bank 0 to 128MB. It was
accidently changed to 124MB here:
commit f928efa818
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Tue Jul 19 09:58:32 2011 +0200
add a add_mem_device function
Add a helper function for boards to register their memory
devices. This makes the board code smaller and also helps
getting rid of map_base and struct memory_platform_data.
And switch all of the memory to it
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding overlay support for phyCORE-i.MX35.
Also move the TEXT_BASE to leave enough space for the overlay image
at the end of the RAM.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added num_modes to all imx_ipu_fb_platform_data structs.
Removed defines for pcm043 to choose display.
We may switch this during runtime now.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init was moved to pure_initcall. broken since:
commit 0adce7ec68
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Sun Jan 15 21:11:17 2012 +0100
ARM omap3: move board_init to pure_initcall
board_init initializes the mux and sdram. For both there is no
need to configure this so early. Move the code to a pure_initcall
and remove the surrounding unneeded code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since commit 494a12f703
platform lowlevel init was moved to mach-omap.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since commit ae2ac15105
a_init was renamed to omap3_core_init and called from board code.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
board_init is now called omap3_board_init. broken since:
commit 494a12f703
Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Sat Jan 14 15:51:05 2012 +0100
omap3: move platform lowlevel init to mach-omap
this will allow to switch omap3 to standard organisation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
