a temporary setting was inserted in the default env by error
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this, the pins seems to be opendrain and thus the LCD signals
are not properly driven leading to wrong colors on the screen.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to execute a program of the host from barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt mainline kernel pxa27x_udc driver to barebox :
- remove function header comments as they are in mainline
- test it with serial gadget
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The core support was brought by Marc and Sascha.
The cache choice was fixed by Luotao Fu.
Some gpio and devices addons were provided by Robert.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Barebox cannot boot the recent mainline Linux kernels for the
i.MX21ADS board anymore when using TFTP, because the heap is too
small.
This is solved by increasing the heapsize to 5Mbyte.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All handlers used to just relocate the image without any checks, so
we are doomed if we write outside of SDRAM or will overwrite ourselves.
Move the relocation up to the generic part where we have a chance
of catching these issues.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that the arch_number and system_rev variables can be set from
the environment we don't need the old bootm command line switch
mechanism anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch_number is currently exported to the environment but not read back
on boot time which is rather confusing. system_rev and system_serial
are not exported to the environment but can be set in board specific
code.
This patch exports all these variables to the environment and reads them
back on boot time. All variables get a armlinux_ prefix, so the
arch_number environment variable gets renamed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We never had interrupt support in barebox and we have no plans to
add interrupt support. Even if we do I doubt the current fragments
of irq support are helpful, so remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rename create_section into create_sections, as the function
is used to create multiple sections, and in particular it
creates the 4096 sections of 1MBytes to have a 1:1 flat
mapping of the 4GBytes address space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These symbols where defined for the A9M2440 platform. Rename them to the
platform they now belong to.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Linux kernel says (spi.h) :
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is
* determined by the results of previous messages and where the whole
* transaction
* ends when the chipselect goes intactive.
In other words, cs_change changes the default chipselect *behavior*.
Support of cs_change is necessary to implement the mci spi driver.
This patch also fix few things:
Passing the bus number to the brand new master device.
Disable chipselect during master->setup.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Eric Bénard
Robert Jarzmik
Franck Jullien
Michael Grzeschik
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Antony Pavlov
Robert Jarzmik
Marc Kleine-Budde
Jaccon Bastiaansen
Juergen Beisert