We introduced several new functions to ease our life
on ppc, use themn on the pcm030:
- setup iomux and bus clocks in board code
- add sdram memory according to detected size
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old startup process consisted of several CFG_LOWBOOT,
CFG_RAMBOOT ifdeffery which I do not understand. So remove
all this and replace it with:
- put the entry point for second stage loaders to offset 0x0
so that we can do a go /dev/ram0 to start a second barebox
- When we come from the reset vector assume MBAR is at 0x80000000
- When we come from the second stage entry assume that
SPR 311 is in sync with the current MBAR address.
- Switch MBAR to 0xf0000000 and we are done.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has never been used in barebox and likely is incomplete
and bitrotted over time, so remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
By doing this we can remove the ptes field in struct arm_memory
which won't be present in a generic memory bank structure anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The nand controller on i.MX51/53 uses two base addresses. Instead
of hardcode the second address use the new shiny resources two specify
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on the Linux driver. Tested with m25p80 with CS in GPIO mode.
Clock setting support is ad-hoc as the corresponding mach is not using
the generic clock infrastructure.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following compile errors
arch/arm/mach-at91/at91sam9g45.c:185:3: error: 'ohci_clk' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9g45.c:186:3: error: 'tcb1_clk' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9g45_devices.c: In function 'at91_add_device_mci':
arch/arm/mach-at91/at91sam9g45_devices.c:258:2: warning: implicit declaration of function 'at91_clock_associate'
[...]
arch/arm/mach-at91/built-in.o: In function `at91_add_device_mci':
sam9_smc.c:(.text.at91_add_device_mci+0x1d0): undefined reference to `at91_clock_associate'
arch/arm/mach-at91/at91sam9260_devices.c: In function 'at91_add_device_mci':
arch/arm/mach-at91/at91sam9260_devices.c:251:2: warning: implicit declaration of function 'at91_clock_associate'
which were introduced in commit:
"at91: swtich to clkdev" (ae19fe26cc)
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
from linux
commit 8251544f9e28058e54c4f35b7cd13b0d191d7555
Author: Ryan Mallon <ryan@bluewatersys.com>
The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can dynamise the boot depending on the machine
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit c71a77ab8 (ns16550: switch to resource) has introduced generic
read/write access to 16550 register and a 'shift' parameter to allign
register index to physicall registers.
The correct 'shift' value was missing in all omap based boards.
Corrected this to 2 which has fixed the problem.
Tested on a PCM-049 phyCORE-OMAP4 board.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Tested-by: Jan Weitzel <J.Weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This helper function can be used for automatic
SDDR configuration based on register settings
made by a previously first stage bootloader
i.e. x-loader.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 7d25a0552dd3a4b65412ae1cbf8f9ca8a88b5d27
Author: Juergen Beisert <jbe@pengutronix.de>
Date: Thu Nov 25 17:49:11 2010 +0100
Keep frequency multiplier enabled to be able to do a warmstart
The wachtdog's reset does only reset the ARM core, not the whole silicon.
But the PLLs seems to do some strange things: It seems they switch back to
the low frequency reference when the watchdog barks. But in the case the
frequency multiplier is off (not used due to 26 MHz reference usage) the
machine stops, because the PLLs are stopping due to the lack of a reference
frequency. As the power on reset will set the FPM_EN bit again, a power cycle
brings the machine back to life.
By keeping the frequency multiplier enabled, also a warmstart triggered by the
watchdog can restart the machine now.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the datasheet, PUE is not effective without PKE set.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Set new CS0 values for new NOR-Flashes (28F256P33BF).
These values also work with older flashes (28F256P33B).
Also removed unnecessary setup of CSO in the core_init call.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Updated mx53 ddr3 script in order to align with the latest Freescale version from July 8, 2011:
-change ESDREF[REF_SEL]=01 (for 32KHz), from incorrect setting of 00 (64KHz)
-change DDR3 MR0 write to "setmem /32 0x63fd901c = 0x052080b0" from "0x092080b0".
This changes write recovery from 8 clocks to 6 clocks(in line with ESDCFG1[tWR])
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These images have to be located in the first 128MB of SDRAM, so
use the following strategy:
- first try to map the image. If the pointer is within the first
128MB of sdram everything is fine.
- if we can't map the image, check for SDRAM being smaller than
128MB we can use malloc for allocating space for the image.
- As a last fallback we simply put the image to 8MB into SDRAM.
This is not very clean. We try our best by checking that we
won't overwrite the malloc space.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some older pcm043 only work correct when cpu frequency is set up
to 399MHz. All modules with revision >= 1315.4 are equipped
with a i.MX35 TO2.1 and do run with 532MHz.
Check the silicon revision and set up the frequency accordingly.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that env_push_context is in a coredevice_initcall
we can initialize barebox_loc earlier so that we can
use it inside later initcalls.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer <s.hauer@pengutronix.de> wrote ..
> On Thu, Aug 11, 2011 at 02:37:05PM +0400, Alexander Shiyan wrote:
> > Hello.
> >
> > Please review and apply this simple patch.
...
> Please remove the #ifdef CONFIG_I2C
OK.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we need to register it before the device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we need to register it before the device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will also fix the clock support as we now switch to allocated generic
device
as we can need to associate the clock and the device but the driver is probe
before the association
we also change the atmel serial name to "atmel_usart" to simplify sharing with
linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- Don't call panic with "resetting CPU...". Depending on the
configuration the system might also hang.
- panic does not return, so no need to call reset_cpu afterwards
- bundle show_regs and panic into a seperate functions to not have
to call both functions from each exception handler
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The exception vector at 0x14 is not used on arm, so no need
to bind this address to a exception handler. Remove the
corresponding code
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The only supported peripheral is ns16550 serial port.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The machine uses only big-endian mode.
Only supported peripheral is serial port.
The machine supports only MIPS32 CPUs.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In barebox we used 1MiB sections to map our SDRAM cachable. This
has the drawback that we have to map our sdram twice: cached for
normal sdram and uncached for DMA operations. As address space gets
sparse on newer systems we are sometines unable to find a suitably
big enough area for the dma coherent space.
This patch changes the MMU code to use second level page tables.
With it we can implement dma_alloc_coherent as normal malloc, we
just have to remap the allocated area uncached afterwards and map
it cached again after free().
This makes arm_create_section(), setup_dma_coherent() and mmu_enable()
noops.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The new MMU setup will need SDRAM base addresses and sizes.
For this reason convert the MMU enabled ARM boards:
- move mem setup to mem_initcall. This is early but
still makes sure that we already have the console available
- move MMU setup in this initcall temporary as after the mmu_init will generic
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
We want to use the memory banks later in the MMU which is
independent of Linux, so move this to a location which is
always compiled.
Also, make the memory bank list global and add an iterator
for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use generic read/write depending on the memory size
if no reg_read/write defined
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
...and update all users. The header file can be used on mx51 and mx53.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The register based fuse readout is not available on i.MX27/31
SoCs, so make explicit sensing the default.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not depend on the specific SoCs for the IIM module, but
instead exclude the one that don't have this unit.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The IIM module uses two drivers, one for the general IIM
module and one for the individual banks.
This patch turns this into a single driver to ease registration
of the resources. This changes the user visible behaviour in
the way that the explicit_sense_enable and permanent_write_enable
device parameters are no longer bank specific but for the
whole device. Also, the IIM module supports a maximum of
8 fuse banks, with these patch all of them are registered, even
if they are not present in a SoC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
pass the hccr and hcor register base via resource
instroduce add_generic_usb_echi_device with hccr = base + 0x100 and
hcor = base + 0x140
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Sascha Hauer
Paul Fertser
Hubert Feurstein
Jean-Christophe PLAGNIOL-VILLARD
Alexander Shiyan
Juergen Kilb
Juergen Beisert
Franck Jullien
Teresa Gámez
Fabio Estevam
Antony Pavlov
Marc Kleine-Budde