use the first 3 byte of the id of a 1-wire
or 6 if no OUI provided device to provide an Ethernet address
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
Based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we to have specific phy init to fix chip issue link detection support
based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to allow to register an array of drivers
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This returns an I2C client bound to the "dummy" driver, intended for use
with devices that consume multiple addresses. Examples of such chips
include various EEPROMS (like 24c04 and 24c08 models).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is needed for i2c-gpio support
Based on linux 3.7-rc2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can show the this of i2c busses
set the bus device as parent of all devices.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As a new implementation of Y-Modem protocol is available,
switch from old implementation to the new one :
- remove old xyzModem* files
- remove old command loady2
- rename command loady2 to loady
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current Y-Modem implementation has some limitations:
- Y-Modem/G protocol is not supported
- Multiple files (aka. batch) transfers are not supported
- Transfer speed over fast lines (USB console) is slow
- Code is not trivial to maintain (personnal opinion)
This implementation tries to address all these points by
introducing loady2 command.
The effects are :
- transfer speed for Y-Modem over USB jumps from 2kBytes/s
to 180kBytes/s
- transfer speed for Y-Modem/G jumps to 200kBytes/s
- multiple file transfers are possible
This command was tested on a USB console and UART 9600bps
serial line :
- NAKs (and retransmissions) were tested for faulty
serial lines
- multiple file transfers were tested
- Y-Modem, Y-Modem/G and X-Modem transfers were tested
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can request a master usefull for the spi command
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allow to do not provide block_isbad at mtd driver level
as example spi flash
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use irq pin as the pin is asserted untill we clear it
This will allow to do not poll on i2c which slow down barebox
If no irq_pin is provided fall back on i2c polling
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The filetype strings are not really suitable for shell scripts, so
add a shortname array of filetypes usable for shell scripts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to avoid issue with resource order
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches environment variables to use linux list. This is easier
to read. An additional plus is that the environment variables no longer
need an initcall, so malloc is the only requirement for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on linux implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
is_timeout call poller_call if the timeout is >= 100us
but on 1-wire bus we need to wait 500us and not more than 930us
for the bus reset. So if the poller_call is caller we can not guarantee it.
So for this introduce is_non_interruptible_timeout than we only wait.
Use it for ndelay too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently in-system update means to write an arbitrary file to
an arbitrary device. There is no sanity check if the flashed image
is of the right type or will fit onto the device. Furthermore some
SoCs need a special preparation step for their images before
flashing them.
This adds a barebox in-system update infrastructure. Boards can
register update handlers which know how to make the board bootable.
The available handlers can be listed to be able to select one,
different force levels give the user the chance to know it better.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If none set use NA (0) as before.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Robert Jarzmik
Andreas Pretzsch
Carlo Caione