Some of the barebox specific changes that were added in commit
e0316b4dd7 got lost during the switch to use
upstream dtsi files in commit bb7cf71cff.
Especially the memory size is important since we have two different memory
sizes which have to be handled.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pingrp defines never made it upstream, so roll back the changes
and use the individual pin defines for the Efika sb instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox used to have its own include/dt-bindings with files copied
from the corresponding kernel files. Use upstream dt-bindings directly
instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise reading or writing to the SPI flash doesn't
work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The virt2real microcontroller, or virturilka,
is a miniature board for creation of WiFi
or internet controllable smart devices.
See http://virt2real.com for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To ease DT import from Linux, which is still maintained in-tree, we
separate barebox-specific changes by including the original dts in
a separate DT file. This allows to overlay modifications and keep
clean DT history. Additionally, this patch updates i.MX27 DTS tree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link ok
imx-sata 10000000.sata: port 0: Spinning up device...
imx-sata 10000000.sata: port 0: ok.
ata0: registered /dev/ata0
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- declare the rigth mux for the GPIO used to enable the USB's 5V
- enable USB host controller
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Using index 0 for the new disk
Bus 002 Device 003: ID 0951:1654 DT R500
Bus 002 Device 002: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I accidently merged the initial data device node which contained
clocks in the sata node which were not compatible to the ones
in the kernel. Fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When booting from SD Card we don't want to load an env
from EMMC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most devices relevant for barebox like sd/emmc/network/uarts
work. Devicetree contains several undefined drive strength settings,
these can be fixed once the kernel has sorted this out.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Michael Olbrich
Silvio Fricke
Beniamino Galvani
Christian Hemp
Eric Bénard
Lucas Stach
Lucas Stach
Antony Pavlov
Alexander Shiyan