Barebox commands should not perform any action and return 0 if an
invalid parameter was given. This might cause undetected unintended
behvaior when calling commands with wrong options, either manually or
from a script.
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The check for is_imx6q was introduced initially in
f1f6d76370 ("ARM: i.MX6: correct work flow of PFDs from uboot-sources")
to differentiate between i.MX6DL+i.MX6SL and i.MX6Q. The i.MX6D must be
handled like the latter, so drop the check. i.MX6DL+i.MX6SL can be
ignored here since since
a665962824 ("imx6: lowlevel_init: Fix workaround for new i.MX6s chips")
the PFD handling is only done for i.MX6DQ.
Update the comment to be not only logically correct but also helpful.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable parent rate propagation for clk_gate2 to allow the
clock consumers to adjust their rates.
One effect of this is that the i.MX6 NAND controller now can adjust
its rate. It already called a clk_set_rate(rate, 96000000), but this
had no effect, so the clock stayed at reset default 24MHz resulting
in a rather slow timing. This became a problem when commit
"1daa3bc mtd: nand_mxs: Setup timing" introduced EDO timing mode for
faster NAND chips. EDO mode can only work properly for cycle times
< 30ns (at least that's specified in the ONFI spec). 1daa3bc resulted
in sporadic NAND read errors on some boards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sam Ravnborg <sam@ravnborg.org>
As a i.MX6dl board dts imx6dl-tx6u.dts should include imx6dl.dtsi, not
the i.MX6q variant. This fixes various pinctrl problems.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX50 SOC includes one ESDHCv3, three ESDHCv2, one cspi and
two ecspi instances which are supported by existing drivers.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move all MX5 clock functionality which does not apply to i.MX50 to
a new mx51_mx53 related function.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add imximg support for i.MX50 processors which use the i.MX flash
header v2 format.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead return just NULL. This matches the behaviour of kstrdup in the
kernel and xstrdup in busybox.
This fixes a panic with CONFIG_CMD_MAGICVAR=y and
CONFIG_CMD_MAGICVAR_HELP unset in magicvar_add() where description is
always NULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch fixes these sphinx issues:
barebox/Documentation/boards/aarch64-qemu-virt.rst:7: WARNING: Title underline too short.
Running barebox on QEMU aarch64 virt machine
^^^^^^^^^^^^^^^^^^^^^^^
barebox/Documentation/boards/aarch64-qemu-virt.rst:1: ERROR: Document or section may not begin with a transition.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch fixes this sphinx warnings:
barebox/Documentation/user/usb.rst:61: WARNING: Could not lex literal_block as "c". Highlighting skipped.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Treat the write() case analogously to the read() case and do not return the
number of most recently written bytes as the status of sucessful command
execution.
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With an unsigned int test for errors from read() can never become true.
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the Linux kernel and the qemu code, the MMCIFIFOCNT contains
the remaining number of words to read, excluding those that are already in
the FIFO. So the current number of bytes in the FIFO is
host_remain - (readl(base + MMCIFIFOCNT) << 2).
Also writing to MMCIDATACTRL will reset the read counter. As a result,
MCI_DATABLOCKEND is never set and read_bytes() waits forever.
With this change, SD-Card support on qemu vexpress works correctly.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix small typo frendly -> friendly
Signed-off-by: Sam Van Den Berge <sam.van.den.berge@telenet.be>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Saveenv should not perform any actions if an invalid parameter was
given.
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to clear a bitmask, "Set" bit has to be '0' and "Mask" bit
'1'. Since "Set" is bit 4 and "Mask" is bit 3 this leaves us with a
overal or-mask of 1 << 3. Orginal code was doing the inverse and setting
bit #4 to '1' bit #3 to '0'.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Re-Implement the DCD v2 processing.
Processing for the DCD write command went into a separate function enabling
the over-all DCD processing to handle check, nop and unlock commands as well.
The trivial NOP command is supported right away.
Further changes: put in some data consistancy checks and error handling, do
structured member access and proper endianess handling and direct error
messages to stderr.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Of_unflatten_dtb returns a ERR_PTR value so checking it against NULL is
incorrect. Fix it in all of the places where this was happening.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
edid_to_display_timings is called in drivers/video/imx-ipu-v3/imx-hdmi.c,
drivers/video/simple-panel.c, and drivers/video/edid.c with the struct
display_timings *timings parameter pointing to an embedded struct
display_timings inside a struct fb_info. The timings pointer is not to
be freed in the error path.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The phyCORE-RK3288 aka PCM-059 is a SoM (System on Module)
containing a RK3288 SoC. The module can be connected to different
carrier boards.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To be able to use PBL console do the usual
relocate_to_current_adr()/setup_c() dance and call pbl_set_putc() to
tell the PBL console where the UART is.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We only allow to setup the host/peripheral role once, when it's already
set then we return -EBUSY.
Return 0 instead when we set the same role again and only return -EBUSY
when we actually try to change the role.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: cb47dde boot: Call blspec_scan_directory() only on strings containing an absolute path
This commit introduced a check if the path contains a '/' at the
beginning. For booting a bootloader spec entry from NFS we have to
test the path for starting with "nfs://" aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The -d option disables any currently active gadget, it does not
necessarily have to be a serial gadget.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: 87c6a88 video/backlight-pwm: fix the value of 'brightness_max'.
brightness_max should really contain the number of brightness steps, so
the number of elements in the brightness array.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The second level page tables can only start at a 1MiB section boundary,
so instead of calling arm_create_pte() with the high vector address
(which is 0xffff0000, not 1MiB aligned) we have to call it with
0xfff00000 to correctly create a second level page table.
The old values broke SoCs which have peripherals in the upper 1MiB
area, like for example the Atmel AT91RM9200. On these Socs we correctly
created the vector page, but the pages around it did not have a 1:1
mapping anymore which led to unreachable peripherals.
Fixes: f6b77fe9: ARM: Rework vector table setup
Reported-by: Peter Kardos <kardos.peter.sk@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Peter Kardos <kardos.peter.sk@gmail.com>
The *-menu-add-entry functions no longer exist in defaultenv-2, so
remove the calls to these functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some boards duplicate the PS1 initialization to add a '#' at the end
of the prompt. It's not worth duplicating this for this purpose. Remove
them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The SDHC used in the RK2928 and RK3288 are compatible with each other.
Add a compatible string for RK3288's SDHC.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>