On barebox-next, I get:
board/freescale-mx25-3-stack/built-in.o: In function `go':
3stack.c:(.flash_header_start+0x0): undefined reference to `_start'
board/freescale-mx25-3-stack/built-in.o: In function `imx25_3ds_fec_init':
3stack.c:(.text.imx25_3ds_fec_init+0x4): undefined reference to `mc34704_get'
3stack.c:(.text.imx25_3ds_fec_init+0x1c): undefined reference to
`mc34704_reg_write'
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this modules is based on Freescale's i.MX357 CPU, with 128MB of
mDDR, 256 MB NAND, and ethernet PHY.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The way it was done before does not work on Cortex processors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Orjan Friberg <of@flatfrog.com>
Tested-by: Luca Ceresoli <list@lucaceresoli.net>
The fec network interface initialization depends on the initialization of the
PMIC. Once the MC34704 driver is registered we can enable the PHY power supply,
and go on with the PHY initialization.
While we are at it convert the hard-coded GPIO registers access to the general
GPIO API for shorter and clearer code.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
theses commands allow low level access to i2c bus and can be useful
to setup an i2c device without having to add code, compile and flash
barebox.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This boards integrates 64mB of DDR, a 256MB NAND flash, a RMII Ethernet PHY
and a i.MX257 CPU.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
_start is now exception_vectors since it was rewritten in C
(not tested on these boards but compile should fail without
this patch)
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The kernel for the imx35 pdk doesn't do any detection for board and chip revision. This patch passes the info to the kernel so that v2 boards/chips boot properly.
imx35pdk: make COMPARE pad a GPIO1_5 output
This pad is an interrupt source, active low for one of the external ICs.
fix up/remove unnecessary white space.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Revision info required for some boards at boot time.
Only adds if the system_rev has been set to non-zero.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Lets translate the startup code to a language we all understand better.
Tested on pcm038 (arm v5) and pcm043 (arm v6).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of having seperate cache flush functions in the startup code
we want to call the generic functions. To accomplish this they have
to be in the bare_init section.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Ivo Clarysse
Sascha Hauer
Eric Benard
Baruch Siach
Marc Reilly