This helper function can be used for automatic
SDDR configuration based on register settings
made by a previously first stage bootloader
i.e. x-loader.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This code was tested barely with m25p80 driver, reading jedec id and some data
from the chip worked fine.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some NOR flash chips have commands with length greater than the maximum
value size of uchar.
Based on an U-Boot Patch by Vasiliy Leoenenko <vasiliy.leonenko@mail.ru>
Only tested with little endian on an intel cfi_flash.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that env_push_context is in a coredevice_initcall
we can initialize barebox_loc earlier so that we can
use it inside later initcalls.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested-by: Marc Reilly <marc@cpdesign.com.au>
env_push_context only needs malloc, so initialize it earlier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested-by: Marc Reilly <marc@cpdesign.com.au>
This patch adds the m25p80 driver. It has been ported from
Linux. MTD code has been removed. It has been tested with
a m25p40 chip and the Altera SPI master driver.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Set new CS0 values for new NOR-Flashes (28F256P33BF).
These values also work with older flashes (28F256P33B).
Also removed unnecessary setup of CSO in the core_init call.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These images have to be located in the first 128MB of SDRAM, so
use the following strategy:
- first try to map the image. If the pointer is within the first
128MB of sdram everything is fine.
- if we can't map the image, check for SDRAM being smaller than
128MB we can use malloc for allocating space for the image.
- As a last fallback we simply put the image to 8MB into SDRAM.
This is not very clean. We try our best by checking that we
won't overwrite the malloc space.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that env_push_context is in a coredevice_initcall
we can initialize barebox_loc earlier so that we can
use it inside later initcalls.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Files associated to a device showed up in a long list. Instead,
print them in seperate lines and also show offset/size information
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer <s.hauer@pengutronix.de> wrote ..
> On Thu, Aug 11, 2011 at 02:37:05PM +0400, Alexander Shiyan wrote:
> > Hello.
> >
> > Please review and apply this simple patch.
...
> Please remove the #ifdef CONFIG_I2C
OK.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise, when a non active device is unregistered, we call
list_del on an unitialized list which oopses.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>