use the first 3 byte of the id of a 1-wire
or 6 if no OUI provided device to provide an Ethernet address
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
Based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we to have specific phy init to fix chip issue link detection support
based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to allow to register an array of drivers
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This returns an I2C client bound to the "dummy" driver, intended for use
with devices that consume multiple addresses. Examples of such chips
include various EEPROMS (like 24c04 and 24c08 models).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is needed for i2c-gpio support
Based on linux 3.7-rc2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can show the this of i2c busses
set the bus device as parent of all devices.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As a new implementation of Y-Modem protocol is available,
switch from old implementation to the new one :
- remove old xyzModem* files
- remove old command loady2
- rename command loady2 to loady
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current Y-Modem implementation has some limitations:
- Y-Modem/G protocol is not supported
- Multiple files (aka. batch) transfers are not supported
- Transfer speed over fast lines (USB console) is slow
- Code is not trivial to maintain (personnal opinion)
This implementation tries to address all these points by
introducing loady2 command.
The effects are :
- transfer speed for Y-Modem over USB jumps from 2kBytes/s
to 180kBytes/s
- transfer speed for Y-Modem/G jumps to 200kBytes/s
- multiple file transfers are possible
This command was tested on a USB console and UART 9600bps
serial line :
- NAKs (and retransmissions) were tested for faulty
serial lines
- multiple file transfers were tested
- Y-Modem, Y-Modem/G and X-Modem transfers were tested
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can request a master usefull for the spi command
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this allow to do not provide block_isbad at mtd driver level
as example spi flash
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use irq pin as the pin is asserted untill we clear it
This will allow to do not poll on i2c which slow down barebox
If no irq_pin is provided fall back on i2c polling
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The filetype strings are not really suitable for shell scripts, so
add a shortname array of filetypes usable for shell scripts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to avoid issue with resource order
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches environment variables to use linux list. This is easier
to read. An additional plus is that the environment variables no longer
need an initcall, so malloc is the only requirement for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on linux implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
is_timeout call poller_call if the timeout is >= 100us
but on 1-wire bus we need to wait 500us and not more than 930us
for the bus reset. So if the poller_call is caller we can not guarantee it.
So for this introduce is_non_interruptible_timeout than we only wait.
Use it for ndelay too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently in-system update means to write an arbitrary file to
an arbitrary device. There is no sanity check if the flashed image
is of the right type or will fit onto the device. Furthermore some
SoCs need a special preparation step for their images before
flashing them.
This adds a barebox in-system update infrastructure. Boards can
register update handlers which know how to make the board bootable.
The available handlers can be listed to be able to select one,
different force levels give the user the chance to know it better.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If none set use NA (0) as before.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a memory bank is already registered, return an error code
instead of throwing a bug. This can happen if a board has registered
a memory bank and the same bank is then probed from the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not blit the surface everytime we write an image
As we want to able to render multiple image this will cause 1 blit per image;
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To open, memmap, get the fb_info and if needed allocate the offscreen buffer
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of passing hundreds of parameter, just pass the right structure.
struct screen represent the screen with a without double buffering.
struct surface represent the part of the screen we want to render.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is needed if the image is bigger than the screen.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can pass -1 for auto detect
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds barebox common clk support loosely based on the Kernel common
clk support. differences are:
- barebox does not need prepare/unprepare
- no parent rate propagation for set_rate
- struct clk is not really encapsulated from the drivers
Along with the clk support we have support for some basic clk building
blocks:
- clk-fixed
- clk-fixed-factor
- clk-mux
- clk-divider
clk-fixed and clk-fixed-factor are completely generic, clk-mux and clk-divider
are currently the way i.MX muxes/dividers are implemented.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most clock/device associations can be done based on the physical
base address of the corresponding device. So instead of depending
on string matching add an optional possibility to associate a clock
lookups with physical addresses. This also has the advantage that
the lookups for devicetree based devices can be identical to the
platform based devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also pass flags using platform_data and remove useless casts from void*.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This is need for oftree device probing
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow reduce the number of driver and device to search on.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We may have some disk with MBR as a first sector. In this case, the
current FAT check returns an error. However, the FAT sector exist and
the MBR can tell us where it is.
This patch add to file_name_detect_type function the ability to find
the FAT boot sector on the first sector of the first partition in case
it is not on sector 0.
It also introduce is_fat_or_mbr to check if a buffer is a FAT boot
or MBR sector
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds code to probe devices from a devicetree. Most helper
functions are directly imported from Linux.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is common for drivers to handle multiple similar devices. On
Linux the driver can distinguish between the devices using the
platform_device_id mechanism. Introduce the same for barebox.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Printing device context normally should be "driver instance:",
but instead we printed the device name twice. This patch fixes
this and as a bonus makes the binary a bit smaller. Instead of
a '@' between driver and instance this function now prints a
whitespace which is a bit more like Linux.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a I2C bus on which the I2C devices and drivers register.
This makes it cleaner as I2C devices won't accidently end up probed by
a platform_device driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a SPI bus on which the SPI devices and drivers register.
This makes it cleaner as SPI devices won't accidently end up probed by
a platform_device driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch sync the image type list with the kernel in order to add
openrisc support.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to render rgba image with or without hw support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to support bmp and png
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can add other format support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to detect the amba device and use the right driver for it at
runtime.
The code is base on linux 3.5.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add functions to read the barebox_arm_head, check barebox magicword
and read out the barebox image size.
Create a inital partion of 1Mb to access the barebox image on nand.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Robert Jarzmik
Andreas Pretzsch
Carlo Caione
Jan Luebbe
Vicente
Franck Jullien
Jan Weitzel