The entry function wasn't changed properly when the
prototype changed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The start-r QSB has a different pmic than the older start QSB.
Add a new dts for the QSRB and let barebox generate two images when
LOCO is selected.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are two versions of the i.MX53 LOCO:
- the MCIMX53-START board
- the MCIMX53-START-R board
The MCIMX53-START-R has a mc34708 pmic and is otherwise the similar to the
MCIMX53-START. To prepare for the START-R, move all common nodes to a new
imx53-qsb-common.dtsi
and remove everything but the board name and pmic from the imx53-qsb.dts.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Solidrun has renamed the Carrier-1 to Hummingboard.
This is also the name that is used in upstream Linux,
change barebox to be in line with that.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Only the 1GB variant is supported for now, as I don't
have anything other to test with.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Needed to be able to update other i.MX 6 DTs properly.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise we end up doing the VMX53 board init for
unrelated boards when using a multiimage build.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for new board variants. Now Supported are:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d/q modules with 1GiB/2GiB Nanya RAM
- i.MX6s modules with 512MiB/1GiB Nanya RAM
This has been tested on:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d module with 2GiB Nanya RAM
- i.MX6s module with 1GiB Nanya RAM
The possible RAM equipment is:
- For the 512MiB module: 2x Nanya nt5cb128m16fp-di
- For the 1GiB modules: 2x Nanya nt5cc256m16cp or 4x Micron MT41K128M16JT-125
- For the 2GiB module: 4x Nanya nt5cc256m16cp
The 512MiB Nanya board is assumed to work with the same DCD table
as the 1GiB Nanya board. The variant is detected by mirroring at
512MiB, but this hasn't been tested by Pengutronix.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using the ANATOP_SI_REV register we can only distinguish between
i.MX6q/d and i.MX6dl/s SoCs. Take the number of cores into account
to get the exact SoC type.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This makes it possible to pull other DT changes from
the linux kernel repo. Plus it will make it possible
to slim down the i.MX6 dtbs at a later point.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reset GPIO now handled from DTS, no need to touch this in the board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch includes update i.MX51 template and porting some barebox
DTS files to use new template.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the pcm038 the ULPI phy is found correctly, but after
a power cycle the attached devices are not found. Adding
some delay fixes this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The ULPI code does not print a message when the operation times
out. Add one to the caller so that he gets an idea that something
is going wrong.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx_chipidea_port_init() will be called during startup from
the ehci driver. Calling it before setting up the PORTSC register
is only necessary in HSIC mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add more paranioa asserts to make it easier to detect
implementation errors.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On error we have to free all three temporary lists.
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The test:
if (!a && b)
a = b;
can be symplified in:
if (!a)
a = b;
And there's no need to test if ubi->image_seq is not null, because if it is,
it is set to image_seq.
So, we just test if image_seq is not null.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
