While this makes sure that the phy fixups are applied even if
networking is not used on i.MX6, this patch due to latest phy
changes causes the startup of barebox delayed until we have a
link on the i.MX fec. Revert it for now and look for a better
solution later.
This reverts commit 3a17af33c0.
as we to have specific phy init to fix chip issue link detection support
based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to allow to register an array of drivers
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 89dfe2d2af "mdiobus: do not scan
the bus at registration time" dropped the check for struct mii_bus
element phy_mask while scanning through all addresses.
Re-add this check.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Scanning the bus can take some time. If we do not need the ethernet
device, this is unnecessary, so delay the scan until the phy device
iactually is needed.
Andread Pretzsch: Fixup bug in scanning for all devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
fec_init() initializes some bits important for phy access, so do
this before the mdiobus is registered. This fixes mdiobus support
on i.MX28 boards in RMII mode.
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Test if we already found a phy device on an address earlier and return
it if it exists. This makes it possible to call mdiobus_scan multiple
times.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several i.MX boards (all i.MX6 boards) need to do some adjustments
to phy registers. If barebox itself does not use network, networking
won't work in the kernel if the kernel does not have the fixups. Connect
the phy at probe time so that these tweaks are done during probe so that
the kernel works without phy register tweaks. Also this has the effect
that the phy device is present and introspectable without doing fake
network transfers beforehand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If none set use NA (0) as before.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On i.MX we enable all necessary clocks during startup of the clock
controller driver, so we do not need the register hacking in the drivers
anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The _send function should not return the length
of the transmitted packet.
See also
commit 76c4c9e48f
Author: Jan Luebbe <jlu@pengutronix.de>
Date: Fri Sep 28 18:17:44 2012 +0200
davinci_emac: return 0 on successful transmit
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the device id mechanism to the i.MX fec driver and
uses it to determine the fec version. Also adds devicetree
probing support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_update_linkspeed':
/opt/work/barebox/drivers/net/designware.c:234:9: error: 'mac_p' undeclared (first use in this function)
/opt/work/barebox/drivers/net/designware.c:234:9: note: each undeclared identifier is reported only once for each function it appears in
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_ether_open':
/opt/work/barebox/drivers/net/designware.c:254:6: error: too few arguments to function 'phy_device_connect'
/opt/work/barebox/include/linux/phy.h:252:5: note: declared here
/opt/work/barebox/drivers/net/designware.c: At top level:
/opt/work/barebox/drivers/net/designware.c:226:13: warning: 'dwc_update_linkspeed' defined but not used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can check it with the kernel one
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also pass flags using platform_data and remove useless casts from void*.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The _send function should not return the length of the transmitted packet.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
this will ensure the data are set to 0 (list as example)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It starts the switch and provides basic access to the registers.
This driver could also work with some other Micrel switches, possibly
with some small changes.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since 99e72c8bbd on an i.MX51 based board,
I get : "phy0: Link is up - 1000/Full". It seems miidev tries to probe
the PHY to early and gets 0x3ffff which leads to the wrong capabilities
setting.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If pdata is NULL smc911x_probe will crash. Checking the zero initialized
priv->shift results in default configuration if pdata is not set.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the check need to be inverted
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
poll the READY bit in PMT_CTRL. Any other access to the device is
forbidden while this bit isn't set. Try for 100ms
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use linux kernel chip detection from 3.5
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Andreas Pretzsch
Antony Pavlov
Jan Luebbe
Eric Bénard
Jan Weitzel