hostname_init() must be called after the devicetree root node has been
initialized, otherwise the check on board compatible always returns
false.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This isn't much different from the default 1,16V
and I haven't seen this make a difference on any
board, but it seems to be required for some T30 SKUs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This board wasn't changed properly, as it was merged in the short
timeframe where the signature change waited to be applied. Change
it now to get rid of the compiler warning.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox now accepts FDTs outside
of it's visible DRAM, as long as it's a valid pointer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox now accepts FDTs outside
of it's visible DRAM, as long as it's a valid pointer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox now accepts FDTs outside
of it's visible DRAM, as long as it's a valid pointer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Mostly to make it clear that boarddata needs to be
something we can dereference.
As this is a pretty invasive change, use the opportunity
to make the signature 64bit safe.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a mtd device can have bad blocks we want to create a
bb device, so do this automatically. This allows us to
drop bb device creation from the environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The purpose of envfs_register_partition is to print an error
message when the partition does not exist. Print an error message
from generic code instead and drop this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox sets this up itself now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fno-jump-tables isn't enough to guard against
gcc switch optimizations that are unsafe to use
in code that runs before relocation.
The switch-tree-conversion opt pass may generate
lookup tables that are placed in the data section
and accessed via absolute adressing, which fails
prior to relocation.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This most likely doesn't fix any real bugs, but it's the
right thing to do and reduces the noise level with static
checkers.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current implementation fakes a memory-mapped I/O device
at 0x3f8 and 0x2f8, then uses platform read/write functions
to do the actual reading and writing. These platform functions
only exist for the x86 platform; better to move the I/O
routines into the driver and have the driver request I/O ports
using request_ioport_region.
Signed-off-by: Michel Stam <michel@reverze.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For a version 1.0 board the rest of loco_late_init should be executed
to completely configure the board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The board code does a phy reset. This implicitly requests the phy reset
gpio. This gpio is also registered in the devicetree as phy reset gpio,
so the fec driver probe can't request the gpio and bails out with -EBUSY.
Fix this by freeing the phy reset gpio in the board code. While at it use
gpio_request_array for the gpios.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
TX_CLK line is approx. 54mm longer than other TX lines which adds
a delay of 0.36ns. RGMII need a delay of min. 1.0ns. This mean we have to add
a delay of 0.64ns. We choose 0.78 to have a little gap. This can be done by
setting GTX pad skew value to 11100
Also add a delay for the RX delay lines, needed for the Duallite variant.
=> Set register 2.8 (RGMII Clock Pad Skew) to 0x039F.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Otherwise it won't get set in a multiimage build.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The virt2real microcontroller, or virturilka,
is a miniature board for creation of WiFi
or internet controllable smart devices.
See http://virt2real.com for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The commit
ARM: Make ENTRY_FUNCTION more robust
changed the behaviour of the ENTRY_FUNCTION. For the Socrates the call to
__barebox_arm_head() was not removed. Do so now otherwise the Socrates will
not be able to boot barebox.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mx31moboard is used on the marXbot, Eyebot and Footbot robot.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Beniamino Galvani
Lucas Stach
Lucas Stach
Sascha Hauer
Christian Hemp
Eric Bénard
Michel Stam
Antony Pavlov
Steffen Trumtrar
Philippe Rétornaz