Switch to new environment and add the bootscripts needed for mmc. Also,
update defconfig for new environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds generic board support (CLEP7212, Linux ARM ID=91)
for CLPS711X-target.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Took the mx28evk defconfig, activated DMA and NAND, used savedefconfig;
this patch is the result.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
now we can flash barebox by itself as the bootstrap need to use pmecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
so be can add more format support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx23-olinuxino is a board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fadil Berisha <f.koliqi@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we are smaller than the 256KiB reserved for barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we are smaller than the 256KiB reserved for barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Tiny6410 and its base board is a pure development platform.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A look into "arch/arm/boards/" offers various boards starting with the
vendor's name in their directory name (like 'eukrea' and 'freescale').
This patch does the same for the currently existing FriendlyARM board
Mini2440.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
This configuration can be used to use barebox as
x-loader replacement.
Also the ECC-Mode is changed from SOFT to BCH8.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for ConnectCore® i.MX51 board from Digi International.
A separate option includes support for debugging board for this module.
Some code taken from the bootloader U-Boot and patch from Digi.
Functional of Ethernet not tested yet.
barebox 2012.05.0-00316-g4024d9c-dirty #0 Wed Jun 6 13:08:25 MSK 2012
Board: ConnectCore i.MX51
Module Variant: i.MX515@600MHz, PHY, Acceleromter (0x0b)
Module HW Rev : 02
Module Serial : B111156789
mc13xxx-spi@mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: Bad block at 0x00ce0000
nand_read_bbt: Bad block at 0x05bc0000
nand_read_bbt: Bad block at 0x0bc40000
ehci@ehci0: USB EHCI 1.00
detected i.MX51 rev 3.0
imx-esdhc@mci0: registered as mci0
imx-esdhc@mci1: registered as mci1
Malloc space: 0x95f00000 -> 0x97efffff (size 32 MB)
Stack space : 0x95ef8000 -> 0x95f00000 (size 32 kB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
Hit any key to stop autoboot: 3
barebox@ConnectCore i.MX51:/
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several boards are getting bigger than their specified maximum binary
size of 256Kb. Enable the TLSF allocator for them which is smaller
than the original dlmalloc. The changed defconfigs are:
eukrea_cpuimx25_defconfig
eukrea_cpuimx35_defconfig
eukrea_cpuimx51_defconfig
usb_a9260_defconfig
usb_a9263_128mib_defconfig
usb_a9263_defconfig
usb_a9g20_128mib_defconfig
usb_a9g20_defconfig
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
with:
- led
- USB Device
- uart
- net
- mmc
- MMU
dfu support
detect it at boot time
if the user button is pressed 5s and the vbus is 1 start the dfu
otherwise the vbus is 1 start usb serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the pcm038 board to the new environment template and
does the necessary defaultconfig adjustments. Additionally it disables
UBI support as the pcm038 image is getting bigger and bigger and UBI
seems to be the most unused big (in size) feature.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Barebox cannot boot the recent mainline Linux kernels for the
i.MX21ADS board anymore when using TFTP, because the heap is too
small.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The MD2 add:
- uart 2
- ethernet
- usb
- spi
- i2c
so fix just add uart and ethernet
update defconfig
always enable the motherboard and drop the SHA256 support (to fix in the
256KiB).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Supported devices:
- nand
- ethernet
- mmc0, mmc1 (on stk5v3 development board)
- led (on stk5v3 development board)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also renamed config option name to MFD_MC13XXX.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pcm027 is a PXA270 based Phytec phyCORE board.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Boot via nfs instead of tftp and zImage.
Update nand partition layout to store the oftree.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Gregory HERMANT <gregory.hermant@calao-systems.com>
Fow now use Soft ECC for nand util we add the PMECC.
On-chip and board related peripherals definitions.
Basic implementation for VB board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- enable MMU
- drop MTD as we do not have nand
- use tlsf
- bootm enable initrd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
FIXME: part of or no data is written. File copy ends
with message: "atmel_mci@atmel_mci0: command/data timeout"
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- change the kernel and rootfs locations
- correct the NAND mtd partitions
- fix the DDR RAM location(so BareBox load address)
- expect the root file system type to be UBIFS
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When CONFIG_DEFAULT_ENVIRONMENT_GENERIC is set the Make system
will automatically compile in defaultenv/ into the environment. Some
boards explicitely add this path again in their defconfig which is
not needed. Remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reduce the size of the MLO we have to activate thumb-2 support.
Otherwise the board will not boot.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- use tslf
- bootm: enable oftree and uimage support
- enable mmu support
- drop cfi support (no nor on the board)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
update fancy prompt to be the same as the other Atmel board
use the same feature on 9g10ek and 9261ek
- use tlsf
- enable MMU
- set max size to 256KiB
- bootm: add initrd support
- nand: drop non used hw ecc and oob device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- set max size to 256KiB
- enable MMU
- bootm: enable oftree and initrd support
- nand: drop non used hw ecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add Mitac MioA701 board initial support.
The support provides basic boot and :
- a console over USB (serial gadget).
- the SD card support
- the MTD docg3 support
- the LCD support
Add a check in the default environment for a barebox.env
file on the first partition (FAT). If the file exists,
source it instead of the normal boot procedure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove what is an apparently valueless Kconfig variable HAS_OMAP_NAND.
A search of the entire source tree shows:
$ grep -r HAS_OMAP_NAND *
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig: select HAS_OMAP_NAND
arch/arm/mach-omap/Kconfig:config HAS_OMAP_NAND
arch/arm/configs/phycard_a_l1_defconfig:CONFIG_HAS_OMAP_NAND=y
$
where the definition of that variable is simply:
config HAS_OMAP_NAND
bool
so it seems pretty clear it can be removed as nothing is using it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding overlay support for phyCORE-i.MX35.
Also move the TEXT_BASE to leave enough space for the overlay image
at the end of the RAM.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Setting up the clocks does not work when the stack is in SDRAM.
Moving the stack to SRAM allows us to do the lowlevel clock setup
later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sanjeev Premi <premi@ti.com>