Enables all relevant errata workarounds for the
i.MX6 SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx_silicon_revision() can't be used from early init context, so
use imx51_silicon_revision() instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the iomux-v3 (found on i.MX25,35,51,53,6) to pinctrl
support. The old SoC specific API is kept for compatibility. The
pinctrl devicetree support is enabled automatically when OFDEVICE
support is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The external NAND boot code currently does not handle bad blocks
correctly on 2k NAND flashes. This patch adds a barebox_update
handler for external NAND boot which embeds a Bad block table in
the flashed image. The boot code will skip bad blocks found in
this bad block table then.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most i.MX boards can use the imx*_barebox_entry functions. The remaining
(i.MX21, i.MX6) use hardcoded base addresses.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for initializing DDR3 RAMs on the i.MX53 type
SDRAM controller. The code automatically detects size/layout of
the connected RAM, detects the bus width and which chipselects are
populated.
While I believe this code is not 100% generic, it is far too
sophisticated to stay in a single board directory. I'm sure
other boards could make use of this aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The code initializing the SDRAM controller is not at the same
place where SDRAM is registered with barebox. To reduce the
risk of registering wrong SDRAM sizes this patch adds a
driver for the ESDCTL which reads back the configured SDRAM
size and registers the memory found with barebox.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for an update handler for internal boot. Currently
handled are:
- v1 MMC/SD
- v2 MMC/SD
- v2 NAND
where v1 is found on i.MX25, i.MX35 and i.MX51. v2 is found on i.MX53.
This code intentionally does not use the DCD data compiled into every
i.MX internal boot image. This makes it possible to make a pure second
stage barebox bootable on i.MX internal boot devices later.
This has been tested on the i.MX51 babbage, i.MX53 loco and i.MX53 tx53
board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The KARO Tx53 board in the revision 8030 has an instable SDRAM
setup. It works as long as the MMU is disabled, but the board
crashes at arbitrary places once the MMU gets enabled. So we
need the PLL setup early. Enable it for pbl.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- for i.MX1 the register is in the System Control unit, so move
the code to arch/arm/mach-imx/imx1.c
- for the other i.MX the register is in the watchdog unit, so move
the code to drivers/watchdog/imxwd.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All i.MX SoCs now use the same imx_silicon_revision() function to get
the revision. Add a separate header file for it and a common function
used on all SoCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old clock support is now unused. Remove it. The former i.MX clko
command is superseeded by generic clock manipulation commands.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a function to take the usbphy1 through its initialization procedure.
The imx6_usb_phy1_disable_oc function is needed at least on the sabrelite,
as the power design is faulty. The state on other imx6 boards is unknown,
therefore it is an extra function call at the moment.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With pbl support enabled most boards need a pbl-y for their lowlevel
stuff.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reimplement the code from lowlevel.S in C. It is run
from SDRAM anyway, so we can safely do this initialization
in a regular barebox environment instead in Assembly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- move code which can be shared between i.MX53 and i.MX51
to a common file
- rename mx53_init_lowlevel to imx53_init_lowlevel
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX Processors support two different boot modes, the internal
boot mode and the external boot mode. Traditionally the external
NAND boot mode is handled in drivers/mtd/nand and the internal
boot mode is handled in arch/arm/mach-imx. This patch consolidates
the handling of both boot modes in arch/arm/mach-imx so that
the user does not have to look in the mtd kconfig section for
booting from NAND. Also, selecting between internal and external
boot mode now is a clear choice.
The external NAND boot mode has been independent of the mtd nand
driver, but as the code was contained in the NAND driver it was
not possible to support booting from NAND without a mtd nand driver.
This is changed with this patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Saves the boot source into an environment variable so env scripts
can more easily use boot source information.
Note only tested on imx35. I haven't added support for any other variants
because I'm not familiar with them. (And can't test them anyway).
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver provides an interface for programming and sensing the IIM fusebox
which is present on some i.MX chips.
Since the IIM io addresses of the controlling registers and each fuse bank are
are not contiguous the driver implementation uses two drivers, imx_iim, and
imx_iim_bank. The imx_iim is the "parent" driver for a device holding the
map_base address of the control registers. The imx_iim_bank driver is for
child devices holding the map_base of each fuse bank. The platform code then,
instantiate one imx_iim_bank device per fuse bank.
Fuses blow is a dangerous operation. Thus, the fuses blow functionality can be
disabled independently at configuration time. On run time this functionality
must be enabled explicitly by setting the permanent_write_enable parameter.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Lucas Stach
Sascha Hauer
Alexander Shiyan
Jean-Christophe PLAGNIOL-VILLARD
Steffen Trumtrar
Juergen Beisert
Marc Kleine-Budde
Marc Reilly
Baruch Siach