commit d7a913469c breaks boot source detection
for pcm049. The tracing vectors shows all tested boot sources, so order is
important. By not returning but overwriting src we effectively reversed the
order if more than one flag is set.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This breaks HSIC and has no good justification why this would
be needed for ULPI.
This reverts commit 2e7d66f526.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some boards need some more tries to successfully detect a phy. This
happens for example on the pcm038. Try up to four times to detect a
phy.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In omap4_enable_all_clocks we not only enable the mcbsp clocks, but also
change the source from ABE_24M_FCLK to 24M_FCLK. Revert this and default
to the reset state.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes boot_mode detection for non-internal boot and
bootsource detection for i2c boot. Further, the bootsouce_instance
is now determined for spi, i2c, and mmc/sd boot.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
By default CONFIG_JZ4750D_DEBUG_LL_UART0 is selected.
This can confuse the Ritmix RZX50 user as the board
has only UART1 connected.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit moves the C debug_ll code from
the MIPS <debug_ll_ns16550.h> header file to
the MIPS <asm/debug_ll_ns16550.h> header file,
so the C code and the asm code can use the same
register address macros.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Set fake DEBUG_LL_UART_DIVISOR to use <asm/debug_ll_ns16550.h>.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Set DEBUG_LL_UART_DIVISOR to use <asm/debug_ll_ns16550.h>.
The JZ4755 uses 24 MHz as the main reference frequency (EXCLK).
The UART controller can work on full EXCLK or on EXCLK/2.
Just now we use EXCLK/2 legacy clock setup made by U-Boot.
So set UART controller base frequency to 12 MHz.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The NT disk Signature is a unique 32-bit value in the MBR allowing
to identify a MSDOS partitioned disk. The signature can be used to
specify the Linux rootfs.
This patch adds support for the NT disk Signature in the form of a
device parameter which can both be read and written.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds macros for ns16550 port initialisation
and single char output. The macros can be used in
MIPS asm pbl code.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Ingenic JZ4755 SoC (JZ4750D family) has three UARTs.
So we can give to the user choose which one of them
to use for low level debug (debug_ll) output.
Also this commit adapts the only JZ4755 board
(Ritmix RZX50) for using the new debug_ll port
selection.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I'm not sure but I guess we don't need defined(__I386__) check.
I kept it for now.
Signed-off-by: Masaki Muranaka <monaka@monami-ya.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In case he configures with make ARCH=x85 menuconfig,
config SPI will be set to "y". And he will got an error on spi.h.
Signed-off-by: Masaki Muranaka <monaka@monami-ya.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It's a precious information that barebox will boot the kernel
with the internal devicetree, so print it even in non verbose
mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jan Weitzel
Lucas Stach
Alexander Shiyan
Markus Niebel
Philipp Zabel
Antony Pavlov
Masaki Muranaka
Masaki Muranaka