FUSEs (OTP registers) can be written via /dev/imx-ocotp character device.
For example, writing MAC 12:34:56:78:9A:BC can be performed as
> mw -l -d /dev/imx-ocotp 0x8c 0x00001234
> mw -l -d /dev/imx-ocotp 0x88 0x56789ABC
and reading as
> md -l -s /dev/imx-ocotp 0x88+8
00000088: 56789ABC 00001234
, where 0x88 (0x22*4) and 0x8C (0x23*4) are offsets of MAC OTP registers.
Notice: FUSEs are PROM, so "0" (unprogrammed) bits
can be replaced with "1" (but not vice versa) only once.
Also, for MAC there are convinient parameters:
> ocotp0.permanent_write_enable=1
> ocotp0.mac_addr=12:34:56:78:9A:BC
imx_ocotp 21bc000.ocotp: reloading shadow registers...
imx_ocotp 21bc000.ocotp: reloading shadow registers...
> echo $ocotp0.mac_addr
12:34:56:78:9A:BC
Signed-off-by: Uladzimir Bely <u.bely@sam-solutions.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the imx6-reg.h include to the imx6-mmdc header.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch corrects exporting unsigned 64-bit environment variables.
I had left out a signed off line before.
Signed-off-by: Michael Burkey <mdburkey at gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We need list_for_each_entry_safe in dev_remove_bb_dev since the
list entries are removed during iteration over the list.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Alexander Aring <alex.aring@gmail.com>
when $target is a path relative to $objtree the script fails.
This is because we cd to $basedir and then copy to $tempdir which
then is no longer valid. Fix this by converting $tempdir to an
absolute path first.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
The pingrp defines never made it upstream, so roll back the changes
and use the individual pin defines for the Efika sb instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox used to have its own include/dt-bindings with files copied
from the corresponding kernel files. Use upstream dt-bindings directly
instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reduce the devicetree files for one board with different memory sizes the
memory size can be read back from i.MX6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a mtd device can have bad blocks we want to create a
bb device, so do this automatically. This allows us to
drop bb device creation from the environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This refactors the code so that we get a mtd_add_bb which can
be used to create a bb dev on a mtd_info.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The devfs layer just adds an addition indirection between mtd
and the bb devices with no purpose. Drop it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The purpose of envfs_register_partition is to print an error
message when the partition does not exist. Print an error message
from generic code instead and drop this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The upstream dts files do not contain the register shift. As
we have Omap specific init code anyway we can just set the register
shift from there instead of relying on the devicetree properties.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the Linux dts files to barebox. The dts files are
generated from Ian Campbells device-tree-rebasing.git:
git://xenbits.xen.org/people/ianc/device-tree-rebasing.git
The dts are found in dts/ in the barebox repository and
will be updated from upstream regularly, probably for each upstream
-rc.
To keep the synchronization with upstream easy no changes to
the original files are allowed under dts/. Instead changes to
upstream dts files will be done using overlays in arch/$ARCH/dts/.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox sets this up itself now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit a162dfe503 the ifup command runs
this file as a script. Due to a hush misbehave it could happen it returns
an error code by accident.
For example if the last instructions in this file are:
if [ false ]; then
echo "friesel"
fi
the hush returns 1 after running this script instead of 0 and in this case
the ifup command fails.
I know, the correct fix would be to fix the hush, because it is a generic
issue...but how?
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The command always sets the MAC address of the interface in the code path.
For the static network configuration case it sets it again, due to the
environment variable keyword ("ethaddr") is listed again in the table.
Remove this keyword from the table, because the MAC is already set.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit a162dfe503 the ifup command is
implemented in C and runs up to two external scripts.
If one of these scripts return with an error code, the command terminates
silently. This can confuse a user because there is no hint about the reason
why it fails. Add error messages to avoid this case.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
No need to store init() function in the driver private structure
since it called only once during startup.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If barebox is builded out-of-tree we don't find the autogenerated
autoconf.h because we search in the srctree.
With this patch we don't get this error message:
cc1: fatal error: /[...]/barebox/include/generated/autoconf.h: No such file or directory
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
From 4ea2bd2e1ca18136d7cfd61643bc8d8187b1495f Mon Sep 17 00:00:00 2001
From: Owen Kirby <osk@exegin.com>
Date: Wed, 16 Apr 2014 17:45:18 -0700
Subject: [PATCH] Fix AT91 UDC driver on boards without vbus.
While porting Barebox to one of our boards, we found that the AT91 UDC driver
will fail to connect to USB hosts, and will spam the console with errors if
the VBUS pin isn't connected.
Signed-off-by: Owen Kirby <osk@exegin.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
uimage_verify already prints an error message if the CRC
is wrong. Romove the never reached redundant message in
the caller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The cast prevents us from doing proper error checking.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The error messages would dereference the just checked NULL
ptr. As those messages don't add much value without further
info just remove them.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Uladzimir Bely
Christian Hemp
Lucas Stach
Michael D. Burkey
Eric Bénard
Juergen Borleis
Alexander Shiyan
Silvio Fricke
Antony Pavlov
Owen Kirby
Lucas Stach