This patch adds a print messages while using 'sf erase' command
to make sure that how many bytes erased in flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Tom Rini <trini@ti.com>
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add board detail function to print more individual board information.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The "cp" command has not worked since
commit 0628ab8ec5,
because of the following lines, which set the destination
and the source to the same address.
buf = map_sysmem(addr, bytes);
src = map_sysmem(addr, bytes);
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Adjust the sizes calculated for whole partition/chip operations by
removing the size of bad blocks so we don't try to erase/read/write
past a partition/chip boundary.
Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
It appears that there are some cases where we have more than 4 banks
of memory. Use CONFIG_NR_DRAM_BANKS if it's defined to handle this.
This will take up a little extra stack space (64 bytes extra if we go
up to 8 banks), but that seems OK.
Signed-off-by: Doug Anderson <dianders@chromium.org>
This makes fixup_silent_linux() use malloc() to allocate its
working space, meaning that our maximum kernel command line
should only be limited by malloc(). Previously it was silently
overflowing the stack.
Note that nothing about this change increases the kernel's maximum
command line length. If you have a command line that is >256
bytes it's up to you to make sure that kernel can handle it.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.
When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:
drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.
Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".
Signed-off-by: Ying Zhang <b40530@freescale.com>
With fewer #ifdefs the code is more readable and more of the code is
compiled for all boards. Add defines in the header file to control
what features are enabled, and then use if() instead of #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems to be a common function for several architectures, so create
a common function rather than duplicating the code in each arch.
Also make an attempt to avoid introducing #ifdefs in the new code, partly
by removing useless #ifdefs around function declarations in the image.h
header.
Signed-off-by: Simon Glass <sjg@chromium.org>
The image file is still very large, and some of the code is only used when
libfdt is in use. Move this code into a new file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is very large, and in SPL it isn't always useful to print
out image information (in fact there might not even be a console
active). So disable this feature unless this option is set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Much of the image code uses addresses as ulongs and pointers interchangeably,
casting between the two forms as needed.
This doesn't work with sandbox, which has a U-Boot RAM buffer which is
separate from the host machine's memory.
Adjust the cost so that translating from a U-Boot address to a pointer uses
map_sysmem(). This allows bootm to work correctly on sandbox.
Note that there are no exhaustive tests for this code on sandbox, so it is
possible that some dark corners remain.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de> (v1)
This function will be used to print signatures as well as hashes, so rename
it. Also make it static since it is not used outside this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The string " error\n" appears in each error string. Move it out to a
common place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The existing function is long and most of the code is indented a long
way. Before adding yet more code, split this out into its own function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de> (v1)
This is the main entry point to the FIT image verification code. We will
be using it to handle image verification with signatures, so rename the
function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This code is never compiled into U-Boot, so move it into a separate
file in tools/ to avoid the large #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The FIT code is about half the size of the >3000-line image.c. Split this
code into its own file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
One we split out the FIT code from image.c we will need this function.
Export it in the header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Rather than repeat the line
#if defined(CONFIG_TIMESTAMP) || defined(CONFIG_CMD_DATE) || \
defined(USE_HOSTCC)
everywhere, put this in a header file and #define IMAGE_ENABLE_TIMESTAMP
to either 1 or 0. Then we can use a plain if() in most code and avoid
the #ifdefs.
The compiler's dead code elimination ensures that the result is the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Rather than needing to call one of many hashing algorithms in U-Boot,
provide a function hash_block() which handles this, and can support all
available hash algorithms.
Once we have md5 supported within hashing, we can use this function in
the FIT image code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which allows a (file, function, line number) to be marked
in bootstage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Che-Liang Chiou <clchiou@chromium.org>
In a previous CL we added the bootstage_relocate(), which should be
called after malloc is initted. Now we call it on generic board.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Any pointers to name strings that were passed to bootstage_mark_name()
pre-relocation should be copied post-relocation so that they don't get
trashed as the original location of U-Boot is re-used for other
purposes.
This change introduces a new API call that should be called from
board_init_r() after malloc has been initted on any board that uses
bootstage.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add softswitch_output command for bf609-ezkit to enable softswitches.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
In bitstream decoding you can directly check device
which you want to load and in fpga.c are fpga_validate
and fpga_dev_info functions which should be used for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Fix the Port status bit constants and Port feature number
constants as a part of USB 2.0 and USB 3.0 Hub class.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Untill now we power-cycle (aka: disable power on a port
and re-enabling again) one port at a time.
Delay of 20ms for Port-power to change multiplies with
number of ports in this case.
So better we parallelize this process:
disable power on all ports, wait for port-power to stabilize
and then re-enable the power subsequently.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
This adds usb framework support for super-speed usb, which will
further facilitate to add stack support for xHCI.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Patch b6d7852c increases timeout for enumeration, taking
worst case to be 10 sec.
get_timer() api returns timestamp in milliseconds, which is
what we are checking in the do-while() loop in usb_hub_configure()
(get_timer(start) < CONFIG_SYS_HZ * 10).
This should give us a required check for 10 seconds, and thereby
we don't need to add additional mdelay of 100 microseconds in
each cycle.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Fetch the device class into usb device's dwcriptors,
so that the host controller's driver can use this info
to differentiate between HUB and DEVICE.
Signed-off-by: Amar <amarendra.xt@samsung.com>
XHCI ports are powered on after a H/W reset, however
EHCI ports are not. So disabling and re-enabling power
on all ports invariably.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Some cleanup in usb framework, nothing much on feature side.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
This patch add support for storing the environment redundant on
mmc devices. Substantially it re-uses the logic from the NAND implementation,
that means using an incremental counter for marking newer data.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
Add "setexpr name gsub r s [t]" and "setexpr name sub r s [t]"
commands which implement substring matching for the regular
expression <r> in the string <t>, and substitution of the string <s>.
The result is assigned to the environment variable <name>. If <t> is
not supplied, the previous value of <name> is used instead. "gsub"
performs global substitution, while "sub" will replace only the first
substring.
Both commands are closely modeled after the gawk functions with the
same names.
Examples:
- Generate broadcast address by substituting the last two numbers of
the IP address by "255.255":
=> print ipaddr
ipaddr=192.168.1.104
=> setexpr broadcast sub "(.*\\.).*\\..*" "\\1255.255" $ipaddr
broadcast=192.168.255.255
- Depending on keyboard configuration (German vs. US keyboard) a
barcode scanner may initialize the MAC address as C0:E5:4E:02:06:DC
or as C0>E5>4E>02>06>DC. Make sure we always have a correct value:
=> print ethaddr
ethaddr=C0>E5>4E>02>06>DC
=> setexpr ethaddr gsub > :
ethaddr=C0:E5:4E:02:06:DC
- Do the same, but substitute one step at a time in a loop until no
futher matches:
=> setenv ethaddr C0>E5>4E>02>06>DC
=> while setexpr ethaddr sub > :
> do
> echo -----
> done
ethaddr=C0:E5>4E>02>06>DC
-----
ethaddr=C0:E5:4E>02>06>DC
-----
ethaddr=C0:E5:4E:02>06>DC
-----
ethaddr=C0:E5:4E:02:06>DC
-----
ethaddr=C0:E5:4E:02:06:DC
-----
C0:E5:4E:02:06:DC: No match
=> print ethaddr
ethaddr=C0:E5:4E:02:06:DC
etc.
To enable this feature, the CONFIG_REGEX option has to be defined in
the board config file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Simplify the argument checking for the "setexpr" command. This is
done mainly to make future extensions easier.
Also improve the help message for the one argument version of the
command - this does not "load an address", but a value, which in
this context may be a plain number or a pointer dereference.
Signed-off-by: Wolfgang Denk <wd@denx.de>
When CONFIG_REGEX is enabled, the new option "-e" becomes available
which causes regular expression matches to be used. This allows for
example things like these:
- print all MAC addresses:
=> env grep -e eth.*addr
eth1addr=00:10:ec:80:c5:15
ethaddr=00:10:ec:00:c5:15
- print all variables that have at least 2 colons in their value:
=> env grep -v -e :.*:
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off
panic=1
eth1addr=00:10:ec:80:c5:15
ethaddr=00:10:ec:00:c5:15
ver=U-Boot 2013.04-rc1-00289-g497746b-dirty (Mar 22 2013 - 12:50:25)
etc.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add options to "env grep" command:
-n : search only the envrironment variable names
-v : search only their values
-b : search both names and values (= default)
An option "--" will stop parsing options, so to print variables that
contain the striing "- " please use:
env grep -- "- "
Or to print all environment varioables which have a '-' in their name,
use:
env grep -n -- -
Signed-off-by: Wolfgang Denk <wd@denx.de>
The output of "env grep" is unsorted, and printing is done by a
private implementation to parse the hash table. We have all the
needed code in place in hexport_r() alsready, so let's use this
instead. Here we prepare the code for this, without any functional
changes yet.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This allows write of files from the host filesystem in sandbox. There is
currently no concept of overwriting the file and removing its existing
contents - all writing is done on top of what is there. This means that
writing 10 bytes to the start of a 1KB file will only update those 10
bytes, not truncate the file to 10 byte slong.
If the file does not exist it is created.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enhance the source command to work with sandbox, by using map_sysmem() to
convert a ulong address into a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit 3b73459ea3.
In practice it doesn't seem like a good idea to make the the working
FDT point to the control FDT. Now that we can access the control FDT
using the 'fdt' command, there is no need for this feature. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is an existing fdt command to deal with the working FDT. Enhance this
to support the control FDT also (CONFIG_OF_CONTROL).
Signed-off-by: Simon Glass <sjg@chromium.org>
This conversion is required in a number of places in U-Boot. Add a
standard function to provide this feature, so we avoid all the different
variations in the way it is coded.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this only checks working_fdt, but we want to check other FDTs
also. So add the FDT to check as a parameter to fdt_valid().
Signed-off-by: Simon Glass <sjg@chromium.org>
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Sometimes it might make sense to verify the written data to NOR flash.
This patch adds this feature. To enable this verify-after-write, you
need to define CONFIG_FLASH_VERIFY in your board config header.
Please note that this option is useless in nearly all cases,
since such flash programming errors usually are detected earlier
while unprotecting/erasing/programming. Please only enable
this option if you really know what you are doing.
Signed-off-by: Stefan Roese <sr@denx.de>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
In common/cmd_nvedit.c, en env_print(), the wrong type is used for len.
hexport_r() returns -1 on error (like OOM), which is converted to
0xffffffff when put in an unsigned. Said value is obviously bigger then
0, and as a result an uninitialized string is then displayed. Other
usages of hexport_r() in the code correctly uses ssize_t to keep its
return value.
Signed-off-by: Maxime Larocque <maxmtl2002@yahoo.ca>
Currently x86 has its own means of managing the global data and board data
(bd_t), and this code resides in start.S. With generic board, we need to
ensure that we leave this alone - i.e. don't clear it as we do on other
archs.
This fixes a problem where the memory init data is cleared which causes
the video driver to operate very slowly.
Signed-off-by: Simon Glass <sjg@chromium.org>
The intention of the memory init code is that it should work the same with
CONFIG_SYS_GENERIC_BOARD and without. This is tricky because dram_init()
is called prior to relocation with generic board (matching other archs)
and after relocation without generic board.
Adjust the init sequence so that dram_init() is not called in the generic
board case, which seems like the easiest fix for now. Also ensure that
relocation addresses are still calculated.
Signed-off-by: Simon Glass <sjg@chromium.org>
TPM command library implements a subset of TPM commands defined in TCG
Main Specification 1.2 that are useful for implementing secure boot.
More TPM commands could be added out of necessity.
You may exercise these commands through the 'tpm' command. However, the
raw TPM commands are too primitive for writing secure boot in command
interpreter scripts; so the 'tpm' command also provides helper functions
to make scripting easier.
For example, to define a counter in TPM non-volatile storage and
initialize it to zero:
$ tpm init
$ tpm startup TPM_ST_CLEAR
$ tpm nv_define d 0x1001 0x1
$ tpm nv_write d 0x1001 0
And then increment the counter by one:
$ tpm nv_read d 0x1001 i
$ setexpr.l i $i + 1
$ tpm nv_write d 0x1001 $i
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
UBI is a better place for the environment on NAND devices because it
handles wear-leveling and bad blocks.
Gluebi is needed in Linux to access the env as an MTD partition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The env in UBI needs to look up the mtd partition as part of relocation,
which happens before relocation. Make the mtdparts code capable of
working on the default env to start with.
The code tries to set values in the env as well, but again, the env
isn't there yet, so add a check to setenv to not allow sets before the
env is relocated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Apparently due to a missed rebase conflict resolution
board_early_init_f() is included twice in the list of initialization
functions.
Leave only the first occurrence.
. built and boot an Exynos 5250 target
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
The header file div64.h includes <asm/types.h> which defines
the phys_addr_t according to the macro CONFIG_PHYS_64BIT, while
the macro CONFIG_PHYS_64BIT is included in common.h which comes
after div64.h, so in order to get consistent type definition for
phys_addr_t, common.h should be included before div64.h, Or else,
the parameters of phys_addr_t type will be passed wrongly when
CONFIG_PHYS_64BIT is defined.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Wolfgang requested this be reverted and Rob agreed after further
discussion. This was a symptom of a larger problem we need to deal
with.
This reverts commit 60d7d5a631.
Signed-off-by: Tom Rini <trini@ti.com>
The "mmc rescan" command takes no arguments. However, executing
"mmc rescan 1" succeeds, leading the user to believe that MMC device 1
has been rescanned. In fact, the "current" MMC device has been
rescanned, and the current device may well not be 1. Add error-checking
to the "mmc" command to explicitly reject any extra command-line
arguments so that it's more obvious when U-Boot isn't doing what the
user thought they asked it to.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most of the various environment functions create CONFIG_ENV_SIZE buffers on
the stack. At least on ARM and PPC which have 4KB stacks, this can overflow
the stack if we have large environment sizes. So move all the buffers off
the stack to static buffers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
After merging LCD patches for v2013.04 the bcm2835 video
driver building is broken due to removal of many global
variables. Fix the driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Adding H/W acceleration support to hash which can be used
to test SHA 256 hash algorithm.
Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The "bootmenu" command uses U-Boot menu interfaces and provides
a simple mechanism for creating menus with several boot items.
When running this command the menu will be assembled as defined
by a set of environment variables which contain a title and
command key-value pairs. The "Up" and "Down" keys are used for
navigation through the items. Current active menu item is
highlighted and can be selected using the "Enter" key.
The command interprets and generates various ANSI escape
sequencies, so for proper menu rendering and item selection
the used terminal should support them.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[agust: various fixes and documentation updates]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Checking the default menu item and obtaining its data can
be useful in custom menu code. Export menu_default_choice()
function which serves this purpose.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Selecting menu items is currently done in menu_interactive_choice()
by reading the user input strings from standard input.
Extend menu_interactive_choice() to support user defined function
for selecting menu items. This function and its argument can be
specified when creating the menu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The ext4write command was taking the in-memory address and filename path
in reverse order from the rest of the filesystem read and write
commands. This corrects the order to be the same as fatload, etc.
Signed-off-by: Tom Rini <trini@ti.com>
This is not called outside of env_callback.c so mark static, remove from
<env_callback.h>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently bitmap logos don't interpret the X coordinate
correctly if the bpp is anything other than 8.
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Hide the console macros since some reference global data which is
no longer present.
cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
- Make the brackets of the function calls more consistent
- Remove really unnecessary brackets
- Removes the extern from the function definitions
- Remove curly brackets from single line statements
- Remove lcd_setmem proto since it is already in common.h
- Cleanup comments, remove useless comments
- Remove NOT_USED_SO_FAR ifdef
- Cleanup coding style
cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: rebased the original patch]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
lcd_base is available as gd->fb_base as well, there is no need
to keep a seperate copy.
For completeness the ack of Bo Shen is for the atmel part.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: also fix cm_t35 board while rebasing]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
console_col, console_row, lcd_line_length, lcd_console_address had
to be declared in board / driver specific code, but were not actually
used there on many boards. Get rid of the global variables.
for completeness, the ack of Bo Shen is for the atmel part
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: rebased and fixed cm_t35 board]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
lcd_color_fg and lcd_color_bg had to be declared in board specific
code, but were not actually used there; in addition, we have getter /
setter functions for these, which were not used either.
Get rid of the global variables, and use the getter function where
needed (so far no setter calls are needed).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[agust: also fixed cm_t35 board while rebasing]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
When an LCD driver is actually driving a regular external display, e.g.
an HDMI monitor, the display resolution might not be known until the
display controller has initialized, i.e. during lcd_ctrl_init(). However,
lcd.c calculates lcd_line_length before calling this function, thus
relying on a hard-coded resolution in struct panel_info.
Instead, defer this calculation until after lcd_ctrl_init() has had the
chance to dynamically determine the resolution. This needs to happen
before lcd_clear(), since the value is used there.
grep indicates that no code outside lcd.c uses this lcd_line_length; in
particular, no lcd_ctrl_init() implementations read it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds the USB Mass Storage Gadget to u-boot
New command called "ums" is implemented to provide access
to on-device embedded persistent memory.
USB Mass Storage is supposed to work on top of the USB
Gadget framework
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marek.vasut@gmail.com>
For x86 the global_data is managed entirely by the start.S code so we do
not need to touch it. However, we do have some more initcalls to add.
Signed-off-by: Simon Glass <sjg@chromium.org>
For x86, things have adjusted somewhat since this series was originally
written. It has its own way of running through initcalls which is actually
nicer than others archs.
Unfortunately this does introduce exceptions. We will soon require use of
generic board on x86, but until then we need to fit in with what is there,
and treat x86 as a special case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds ppc features to the generic pre-relocation board init.
This is a separate commit so that these features are clearly shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Link symbols as created by the link script can either be absolute or
relative to the text start. This option switches between the two options
so that we can support both.
As we convert architectures over to generic board, we can see if this
option is actually needed, or whether it is possible to unify this feature
also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file handles common pre-relocation init for boards which use
the generic framework.
It starts up the console, DRAM, performs relocation and then jumps
to post-relocation init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.
Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.
Conflicts:
arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
board/ait/cam_enc_4xx/u-boot-spl.lds
board/davinci/da8xxevm/u-boot-spl-da850evm.lds
board/davinci/da8xxevm/u-boot-spl-hawk.lds
board/vpac270/u-boot-spl.lds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Because the code that handles bootdelay is compiled in conditionally
based on the default value, you are restricted in the default,
regardless of what you want the runtime options to be.
Change the source to always check if any default is given so that other
values can be selected and used at runtime.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The "env ask" traditionally uses a somewhat awkward syntax:
env ask name [message ...] [size]
So far, when a mesage was given, you always also had to enter a size.
If you forgot to do that, the command would terminate without any
indication of the problem.
To avoid incompatible changes of the interface, we now check the last
argument if it can be converted into a decimal number. If this is the
case, we assume it is a size; otherwise we treat it as part of the
message.
Also, add a space after the message fore easier reading,
and clean up help mesage.
Signed-off-by: Wolfgang Denk <wd@denx.de>
When using the partial read feature of fatwrite the buffer we read into
can become unaligned not just due to initial location but the size of
our partial reads as well. Make this clear in the help text.
Signed-off-by: Tom Rini <trini@ti.com>
Add generic TMU support alongwith i2c sensors in dtt command
to enable temperature reading in cases where TMU is present
along-with/instead-of i2c sensors.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The core implementation of "help" already prints the command name before
the help text of a specific command. Remove it from part's own help text
to avoid it being printed twice:
Tegra114 (Dalmore) # help part
part - disk partition related commands
Usage:
part part uuid <interface> <dev>:<part>
- print partition UUID
...
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The "mtest" command is of little practical use (if any), and
experience has shown that a large number of board configurations
define useless or even dangerous start and end addresses. If not even
the board maintainers are able to figure out which memory range can be
reliably tested, how can we expect such from the end users? As this
problem comes up repeatedly, we rather do not enable this command by
default, so only people who know what they are doing will be
confronted with it.
As this changes the user interface, we allow for a grace period
before this change takes effect. For now, we make "mtest"
configurable through the CONFIG_CMD_MEMTEST variable, which is defined
in include/config_cmd_default.h; we also add an entry to
doc/feature-removal-schedule.txt which announces the removal of this
default setting in two releases from now, i. e. with v2013.07.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
On some architectures certain values of splashimage will lead to
a data abort exception.
Document the problem, and implement a callback for splashimage to
reject such values.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch will allow use SPL to boot an u-boot from the OneNAND.
Tested with IGEPv2 board with a OneNAND from Numonyx
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
[trini: Add <spl.h> hunk to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
Currently there is no logical place to put the code that prepares the
splash image data. The splash image data should be ready in memory
before bmp_display() is called, and after the environment is ready
(since lcd.c looks for the splash image in an address specified by
the environment variable "splashimage").
Our window of opportunity in board_init_r() is therefore: between
env_relocate() and bmp_display(), and from the available options
only the lcd related functions in drv_lcd_init() seem appropriate
for such lcd oriented code.
Add the option to prepare the splash image data in lcd_logo() right
before it is sent to be displayed.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
All code related to the bootm ramdisk subcommand is conditionally
enabled by CONFIG_SYS_BOOT_RAMDISK_HIGH except for the help message.
Replace the CONFIG_ARCH defines by CONFIG_SYS_BOOT_RAMDISK_HIGH
to fix this.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The new 'sb' command is intended to deal with sandbox-specific features
that have no parallel in other archs. This commit adds two sub-commands
to list a directory and read a file from the host filesystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Set up clocks, DDR controller, Nor flash controller, reboot,
serial port. Add new SPI boot modes.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Rather than use strcasecmp() in the hash algorithm search, require the
caller to do this first. Most of U-Boot can use lower case anyway, and
the hash command can convert to lower case before calling hash_command().
This saves needing strcasecmp() for boards that use hashing but not
the hash command.
Signed-off-by: Simon Glass <sjg@chromium.org>
This config effectively has a default value of 0, so add this setting
at the top of the code to remove an #ifdef in the C function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the CRC32 algorithm to the list of available hashes, and make
the crc32 command use hash_command(). Add a new crc32_wd_buf() to
make this possible, which puts its result in a buffer rather than
returning it as a 32-bit value.
Note: For some boards the hash command is not enabled, neither
are sha1, sha256 or the verify option. In this case the full
hash implementation adds about 500 bytes of overhead. So as a
special case, we use #ifdef to select very simple bahaviour in
that case. The justification for this is that it is currently
a very common case (virtually all boards enable crc32 but only
some enable more advanced features).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some hashing commands permit saving the hash in an environment variable,
and verifying a hash from there. But the crc32 command does not support
this. In order to permit crc32 to use the generic hashing infrastructure,
add a flag to select which behaviour to use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use a ulong for the command arguments, and only cast to an address when
needed. This fixes warnings in sandbox where pointers are typically 64 bits
long.
Signed-off-by: Simon Glass <sjg@chromium.org>
If we get a Ctrl-C abort, we always print a newline. Move this repeated
code out of the functions and into a single place in the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
The iteration code is the same for each version of the memory test, so
pull it out into the common function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Half of the code is currently hidden behind an #ifdef. Move the two
memory tests into their own functions and use the compiler to eliminate
the unused code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox wants to support commands which use memory. The map_sysmen()
call provides this feature, so use this in the memory commands.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are two problems:
1. The argument count needs to be checked before argv is used
2. When verify is not enabled, we need to define a constant zero value
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently sata usage text prints a double 'sata' for the init command.
MX53LOCO U-Boot > sata
sata - SATA sub system
Usage:
sata sata init - init SATA sub system
sata info - show available SATA devices
sata device [dev] - show or set current device
sata part [dev] - print partition table
sata read addr blk# cnt
sata write addr blk# cnt
Remove the extra 'sata' from the 'sata init' line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Calculating the checksum of incompletely read data is useless.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
[scottwood@freescale.com: minor formatting fix]
Signed-off-by: Scott Wood <scottwood@freescale.com>
The single message is misleading, since there is no equivalent success
note when reading the other copy succeeds. Instead, warn if one of the
redundant copies could not be loaded and emphasise on the error when
reading both fails.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
"nand read.part addr off size" would be treated as "nand read.raw addr off 1"
It now fails as intended stating "Unknown nand command suffix '.part'"
Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
Currently, in gpt command, partion size is converted from string
to unsigned long type using 'ustrtol' function. That type limits
the partition size to 4GB.
This patch changes the conversion function to 'ustrtoll' to return
unsigned long long type.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
u-boot is not consistent if state should be 0|1 or of the enum, the
GPIO driver expects this to be one of the enum values. Update the
caller.
Signed-off-by: Holger Hans Peter Freyther <holger@freyther.de>
On architectures where manual relocation
is needed, the 'malloc_bin_reloc' function
must be called after 'mem_malloc_init'.
Make the 'malloc_bin_reloc' function static
and call it directly from 'mem_malloc_init'
instead of calling that from board_init_{r,f}
functions of the affected architectures.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andreas Bießmann <andreas.devel@gmail.com>
Cc: Jason Jin <Jason.jin@freescale.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
In case of usbeth booting just call net_load_image("usb_ether").
This patch also adds CONFIG_SPL_USBETH_SUPPORT and
CONFIG_SPL_MUSB_NEW_SUPPORT config options to enable linking of SPL
against USB gagdet support and new MUSB driver resp.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
trivial:
fdt_support.c:89:64: warning: Using plain integer as NULL pointer
fdt_support.c:325:65: warning: Using plain integer as NULL pointer
fdt_support.c:352:65: warning: Using plain integer as NULL pointer
For the following bad constant expression, We hardcode the max. number of
memory banks to four for the foreseeable future, and add an error with
instructions on what to do once it's exceeded:
fdt_support.c:397:22: error: bad constant expression
For the rest below, sparse found a couple of wrong endian conversions
in of_bus_default_translate() and fdt_get_base_address(), but
otherwise the rest is mostly annotation fixes:
fdt_support.c:64:24: warning: cast to restricted __be32
fdt_support.c:192:21: warning: incorrect type in assignment (different base types)
fdt_support.c:192:21: expected unsigned int [unsigned] [usertype] tmp
fdt_support.c:192:21: got restricted __be32 [usertype] <noident>
fdt_support.c:201:21: warning: incorrect type in assignment (different base types)
fdt_support.c:201:21: expected unsigned int [unsigned] [addressable] [usertype] tmp
fdt_support.c:201:21: got restricted __be32 [usertype] <noident>
fdt_support.c:304:13: warning: incorrect type in assignment (different base types)
fdt_support.c:304:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:304:13: got restricted __be32 [usertype] <noident>
fdt_support.c:333:13: warning: incorrect type in assignment (different base types)
fdt_support.c:333:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:333:13: got restricted __be32 [usertype] <noident>
fdt_support.c:359:13: warning: incorrect type in assignment (different base types)
fdt_support.c:359:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:359:13: got restricted __be32 [usertype] <noident>
fdt_support.c:373:21: warning: cast to restricted __be32
fdt_support.c:963:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:963:48: expected restricted __be32 const [usertype] *p
fdt_support.c:963:48: got unsigned int [usertype] *<noident>
fdt_support.c:971:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:971:48: expected restricted __be32 const [usertype] *p
fdt_support.c:971:48: got unsigned int [usertype] *<noident>
fdt_support.c:984:29: warning: incorrect type in argument 1 (different base types)
fdt_support.c:984:29: expected restricted __be32 const [usertype] *cell
fdt_support.c:984:29: got unsigned int [usertype] *addr
fdt_support.c:996:32: warning: incorrect type in argument 1 (different base types)
fdt_support.c:996:32: expected restricted __be32 const [usertype] *cell
fdt_support.c:996:32: got unsigned int [usertype] *addr
fdt_support.c:1041:41: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1041:41: expected restricted __be32 const [usertype] *cell
fdt_support.c:1041:41: got unsigned int [usertype] *addr
fdt_support.c:1053:41: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1053:41: expected restricted __be32 const [usertype] *range
fdt_support.c:1053:41: got unsigned int const [usertype] *[assigned] ranges
fdt_support.c:1064:53: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1064:53: expected restricted __be32 const [usertype] *addr
fdt_support.c:1064:53: got unsigned int [usertype] *addr
fdt_support.c:1110:50: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1110:50: expected restricted __be32 const [usertype] *addr
fdt_support.c:1110:50: got unsigned int *<noident>
fdt_support.c:1121:49: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1121:49: expected restricted __be32 const [usertype] *cell
fdt_support.c:1121:49: got unsigned int *<noident>
fdt_support.c:1147:60: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1147:60: expected restricted __be32 const [usertype] *addr
fdt_support.c:1147:60: got unsigned int *<noident>
fdt_support.c:1081:5: warning: symbol '__of_translate_address' was not declared. Should it be static?
fdt_support.c:1154:5: error: symbol 'fdt_translate_address' redeclared with different type (originally declared at include/fdt_support.h:95) - incompatible argument 3 (different base types)
fdt_support.c: In function 'fdt_node_offset_by_compat_reg':
fdt_support.c:1173:17: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
See also linux kernel commit 0131d897 "of/address: use proper
endianess in get_flags".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
and, if including libfdt.h which includes libfdt_env.h in
the correct order, don't include fdt.h before libfdt.h.
this is needed to get the fdt type definitions set from
the project environment before fdt.h uses them.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
CONFIG_ARM_DCC_MULTI should be also removed in the patch
"serial: Remove CONFIG_SERIAL_MULTI from serial drivers"
(sha1: a382725060)
Because the driver defines serial_* functions
which cause conflict with serial.c (multiple definition of serial_*)
Removing CONFIG_SERIAL_MULTI function also require to define
default_serial_console for cases where another serial driver
is not available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
As far as every arch has a get_timer function,
run_command_and_time_it code can now disappear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-By: Che-Liang Chiou <clchiou@chromium.org>
[trini: s/ulong/unsigned long/ in command.h portion]
Signed-off-by: Tom Rini <trini@ti.com>
Autoboot timeout defined by CONFIG_BOOTDELAY will not be accurate if
CONFIG_USB_KEYBOARD and CONFIG_SYS_USB_EVENT_POLL are defined in
configuration file and when tstc() function for checking key pressed
takes longer time than 10 ms (e.g., 50 ms) to finish.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Using the __weak annotation can make the code cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The execution order of the bootm subcommands is fixed.
Although here is a sanity check in the state machine
which should prevent running the subcommands in wrong
order but it does not catch all possible errors.
It is possible to run any subcommand without running
'bootm start' first which leads to unexpected behaviour.
For example, running 'bootm loados' without 'bootm start'
causes a hang:
U-Boot> bootm loados
XIP Invalid Image ... OK
OK
Add a sanity check to 'do_bootm_subcommand' in order
to ensure that no subcommands can be executed before
'bootm start'.
After the patch running of any subcommand without running
'bootm start' will cause an error like this:
U-Boot> bootm loados
Trying to execute a command out of order
bootm - boot application image from memory
Usage:
bootm [addr [arg ...]]
- boot application image stored in memory
...
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
The ideal of having a frame buffer when there isn't a display is not
that useful. Change the bdinfo command to expect this only when we
have an lcd or video display.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix one printf compilation warning in microblaze bdinfo part.
Warning log:
cmd_bdinfo.c: In function 'do_bdinfo':
cmd_bdinfo.c:219:2: warning: format '%u' expects argument of type
'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move these fields into arch_global_data and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Address tlb_size in this patch as well]
Signed-off-by: Tom Rini <trini@ti.com>
Commit fb6a9aab7a (LCD: display 32bpp decompressed bitmap image)
broke the check that allowed U-Boot to display 8 bpp BMPs on a 16
bpp LCD screen, effectively turning this feature off.
Restore this feature by changing the check back to the same meaning
it originally had.
To avoid future confusion, the check has also been rephrased to make
its meaning clear.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
To make bootm sub-command feature working on archs with CONFIG_NEEDS_MANUAL_RELOC,
the name pointers in the sub-command table need to be relocated.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Some boards want to report more than just memory size. For example, it
might be useful to display the memory type (DDR2, DDR3) or manufacturer.
Add a weak function to support this requirement, accessed through a new
'meminfo' command.
Any example of the DRAM: output is below, just for illustration:
SMDK5250 # meminfo
DRAM: 2 GiB Elpida DDR3 @ 800MHz
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds FDT support to sound init in CMD.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since U-Boot runs from coreboot on x86, the Coreboot version is an
important part of the boot state. This version information is
available in the coreboot tables, so print it when the 'version'
command is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make setexpr accept a 2 parameter variant that will simply load a value
into a variable. This is useful for loading a value from memory.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
It is useful to have a basic SPI flash test, which tests that the SPI chip,
the SPI bus and the driver are behaving.
This test erases part of the flash, writes data and reads it back as a
sanity check that all is well.
Use CONFIG_SF_TEST to enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Output a progress update only at most 10 times per second, to avoid
saturating (and waiting on) the console. Make the summary line
to fit on a single line. Make sure that cursor sits at the end of
each update line instead of the beginning.
Sample output:
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
Update SPI
1331200 bytes written, 2863104 bytes skipped in 21.912s, speed 199728 B/s
time: 21.919 seconds, 21919 ticks
Skipping verify
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: James Miller <jamesmiller@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
[trini: Drop 'const' from bytes_per_second()]
Signed-off-by: Tom Rini <trini@ti.com>
When a USB card reader is empty, it will return "Not Ready - medium not
present" as Key Code Qualifier. In that situation, it's useless waiting
for the full timeout since the result won't change until the user
inserts a card.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
If probe of a newly connected device fails for some reason, clean up
the allocated entry in usb_dev array.
Signed-off-by: Milind Choudhary <milindc@codeaurora.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current logic reads the port status just once after usb_hub_power_on and
expects the portstatus and portchange to report the connection status
immediately and correctly.
Few pen drives are not able to report both of them immediately ie. those pens
report the connection change but not the connected state after the first read.
This opportunity once lost is gone for ever because the u-boot, unlike linux or
any other OS, works in polling mode.
This patch modifies the logic to read the port status continuously until the
portstatus and portchange both report a connection change as well as a connected
state or no connection change and no connection. This logic is placed in a
timeout of 10 sec. At the end of it, the pen drive would have either reported a
ONE or a ZERO in bit 1 of portstatus as well as portchange.
It enhances the set of pen drives which can eventually be detected by u-boot
Note: This 10 second timeout is based purely on several experiments done with
the broken pen drives
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Use the variable access flags to implement the protection for ethaddr
and serial# instead of hard-coding them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Similar to the env callback command, this will show details about the
options available, the static list, and the currently active variables.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address. Call
env_acl_validate_setenv_params() from setenv() in fw_env.c.
If the entry is not found in the env .flags, then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Need to build in _ctype for isdigit for Linux.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address.
If the entry is not found in the env ".flags", then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The silent variable now updates the global data flag anytime it is
changed as well as after the env relocation (in case its value is
different from the default env in such cases as NAND env)
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The callbacks can be bound, but are otherwise invisible. Add a command
to show what callbacks are available.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!! fix callback command
Add support for per-variable callbacks to the "hashtable" functions.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!!fix comment in callback
When printing all variables with env print, don't print variables that
begin with '.'. If env print is called with a '-a' switch, then
include variables that begin with '.' (just like the ls command).
Variables printed explicitly will be printed even without the -a.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the read of the old value to inside the check function. In some
cases it can be avoided all together and at the least the code is only
called from one place.
Also name the function and the callback to more clearly describe what
it does.
Pass the ENTRY instead of just the name for direct access to the whole
data structure.
Pass an enum to the callback that specifies the operation being approved.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use a flag in hsearch_r for insert mode passed from import to allow the
behavior be different based on use.
Now that "do_check" is called for all imports, ensure console init is
complete before updating the console on relocation import
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
New command - "gpt" is supported. It restores the GPT partition table.
It looks into the given environment variable for partitions definition.
It can be enabled at target configuration file with CONFIG_CMD_GPT.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Do not compile in FDT related code, when it is not supported.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add a simple command to stress-test a TPM (Trusted Platform Module).
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The CONFIG_SYS_CONSOLE_INFO_QUIET option should suppress the console
information, but allow boards to display it later if required. Adjust
the code to support this.
This is used to avoid printing the information while the LCD display
is not ready, since it only becomes ready when stdio init is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be used for LCDs as well as monitors.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a single command to read the EDID information over I2C.
For example:
SMDK5250 # i2c dev 7
Setting bus to 7
SMDK5250 # i2c edid 50
EDID version: 1.4
Product ID code: 305c
Manufacturer: AUO
Serial number: 00000000
Manufactured in week: 0 year: 2011
Video input definition: digital signal, voltage level 0, blank to black
Monitor is non-RGB
Maximum visible display size: 26 cm x 14 cm
Power management features: no active off, no suspend, no standby
Estabilished timings:
Standard timings:
1366x768 60 Hz (detailed)
1366x768 60 Hz (detailed)
Monitor ID: 2VD2K.B116XW
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This implements a library for accessing EDID data from an LCD panel.
This is used to obtain information about the panel such as its
resolution and type.
This is a tidied-up version of the original code pulled from
https://github.com/ynezz/u-boot-edid.
The changes we made are:
- removed bit fields in the struct;
- removed endianness cases in the struct;
- fixed some wrong definitions;
- fixed to fit 80 columns;
- fixed some code styles.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This new command supports hashing SHA1 and SHA256. It could be extended
to others such as MD5 and the CRC algorithms. The syntax is modeled on
those:
hash <algorithm> <address> <length> [*<dest_addr> | <dest_envvar>]
to calculate a hash, and:
hash -v <algorithm> <address> <length> [*<verify_addr> | <verify_envvar>]
to verify a hash.
Use CONFIG_CMD_HASH to enable the command, CONFIG_SHA1 to enable SHA1 and
CONFIG_SHA256 to enable SHA256.
The existing sha1sum command remains.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a SHA1 command and want to add a SHA256 command also. Instead of
duplicating the code, create a generic hash API which can process
commands for different algorithms.
Signed-off-by: Simon Glass <sjg@chromium.org>
The name is already copied when we memcpy() the whole structure.
This is because struct stdio_dev has this field:
char name[16]; /* Device name */
So the data is inline, rather than being a pointer.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes data is on a block device and within a partition, but not in a
particular filesystem.
This commands permits reading raw data from a partition.
Signed-off-by: Kenneth Waters <kwaters@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Gettime returns the current timer value. If CONFIG_SYS_HZ is defined
then the timer value is also converted to seconds.
Tegra20 (SeaBoard) # gettime
Timer val: 7754
Seconds : 7
Remainder : 754
sys_hz = 1000
There has been some discussion about whether this is useful enough to
be included in U-Boot. The following boards do not have CONFIG_SYS_HZ
defined:
M52277EVB
M52277EVB_stmicro
M53017EVB
M54418TWR
M54418TWR_nand_mii
M54418TWR_nand_rmii
M54418TWR_nand_rmii_lowfreq
M54418TWR_serial_mii
M54418TWR_serial_rmii
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add kerneldoc style documentation into cmd_i2c.c to properly describe
all overridable functions and most of the command interface.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Use __weak from linux/compiler.h instead of __attribute__((weak, alias))
to define overridable function. This patch is intended as a cleanup patch
to bring some consistency into the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Current "led" help and usage info has redundancy and extraneous
newlines, tweak it to be consistent with other commands.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
With this patch, getenv_f() can be included easily into the SPL
binary. With this, SPL boards can now use getenv_f() to read
environment variables (e.g. to detect if the OS or U-Boot shall
be executed).
In the approach this is done for env stored in NOR flash, as this
will be used by an upcoming MPC5200 board port.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the SPL framework to be used on powerpc platforms
and not only ARM.
timer_init() does not exist on PPC systems. The timer (decrementer) is
initialized and enabled in interrupt_init() here. And currently
interrupt_init() is called after relocation to SDRAM. Since the only
powerpc SPL implementation (a3m071) doesn't need a timer, let's remove
this timer_init() call for PPC systems.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch builds upon the recently introduced CBMEM console
feature of coreboot.
CBMEM console uses a memry area allocated by coreboot to store
the console output. The memory area has a certain structure,
which allows to determine where the buffer is, the buffer size
and the location of the pointer in the buffer. This allows
different phases of the firmware (rom based coreboot, ram based
coreboot, u-boot after relocation with this change) to keep
adding text to the same buffer.
Note that this patch introduces a new console driver and adds the
driver to the list of drivers to be used for console output, i.e.
it engages only after u-boot relocates. Usiong CBMEM console for
capturing the pre-relocation console output will be done under a
separate change.
>From Linux, run the cbmem.py utility (which is a part of the coreboot
package) to see the output, e.g.:
vvvvvvvvvvvvvvvvv
SCSI: AHCI 0001.0300 32 slots 6 ports ? Gbps 0xf impl SATA mode
flags: 64bit ilck stag led pmp pio
...
Magic signature found
Kernel command line: "cros_secure quiet loglevel=1 console=tty2...
^^^^^^^^^^^^^^^^^
Note that the entire u-boot output fits into the buffer only if
the coreboot log level is reduced from the most verbose. Ether
the buffer size will have to be increased, or the coreboot
verbosity permanently reduced.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We need an extra condition here in case we want to use fdt without the
silent console/cmdline editing/post options. It is easier to just remove
the #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
If a malformed 'read' or 'write' command is issued, the Sandbox U-Boot
can crash because the command-handling code does no error checking on
the number of provided arguments.
This change makes the mmc 'erase', 'read' and 'write' commands only
function if the proper number of arguments are supplied.
Also puts the else assignment at the beginning fo the if() statement
to shortens the generated code. This removes an unnecessary jump from
the generated code.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The current bouncebuf API requires all parameters to be passed to both
bounce_buffer_start() and bounce_buffer_stop(). Modify the bouncebuf
start function to accept a state structure as a parameter, and only
require that state struct to be passed to the stop function. This
simplifies usage of the bounce buffer by clients.
Don't modify the data pointer, but rather store the temporary buffer in
this state struct. The bouncebuf code ensures that client code can
always use a single buffer pointer in the state structure, irrespective
of whether a bounce buffer actually had to be allocated.
Move cache management logic into the bounce buffer code, so that each
client doesn't have to duplicate this. I believe there's no need to
invalidate the buffer before a DMA operation, since flushing the cache
should prevent any write-backs.
Update the MXS MMC driver for this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Check for scancodes for arrow keys and map them to ^F/^B, ^N/^P.
Control characters are used instead of ANSI sequence because the
queueing code in usb_kbd doesn't handle the data increase when one
keypress generates 3 keycodes. The real fix is to convert this driver
to use the input subsystem and queue, but this allows arrow keys to
work until this driver is converted.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Change usb_kbd driver to obey alignment requirements for USB DMA on
the buffer used for data transfer. This is necessary for
architectures that enable dcache and enable USB DMA.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
When the cursor position gets to the end of the LCD console we normally
scroll by one line. This adds an option to increase that value.
Console scrolling is often slow, and if a large amount of output is
being sent, increasing this option to 10 or so will speed things up
considerably.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This provides an option for the LCD to flush the dcache after each update
(puts, scroll or clear).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The normal alignment is PAGE_SIZE, but if this is defined, we can support
other alignments.
The motivation for this change is to make the display section-aligned on
ARM so that we can easily turn off data caching for the frame buffer region
without resorting to level 2 page tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds command to test audio playback.
sound init - Initialises the audio subsystem (i2s and wm8994 codec)
sound play - Plays predefined the audio data when specified length
and frequency.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If kernel-offset is specified in the fdt, set an environment variable
so that scripts can access the attached kernel.
This can be used by a packaging program to tell U-Boot about a kernel
that has been downloaded alongside U-Boot. The value in the fdt is
the offset of the kernel from the start of the U-Boot image, so we can
find it just by adding CONFIG_SYS_TEXT_BASE.
It is then fairly easy to put something like this in the environment
variables in the board header file:
"if test ${kernaddr} != \"\"; then "\
"echo \"Using bundled kernel\"; "\
"bootm ${kernaddr};" \
"fi; "\
/* rest of boot sequence follows here */
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting a fit image with multiple configurations, the user either has to
specify which configuration to use explicitly, or there has to be a default
defined which is chosen automatically. This change adds an option to change
that behavior so that a configuration can be selected explicitly, or the
configuration which has the device tree that claims to be compatible with the
earliest item in U-Boot's device tree.
In other words, if U-Boot claimed to be compatible with A, B, and then C, and
the configurations claimed to be compatible with A, D and B, D and D, E, the
first configuration, A, D, would be chosen. Both the first and second
configurations match, but the first one matches a more specific entry in
U-Boot's device tree. The order in the kernel's device tree is ignored.
Signed-off-by: Gabe Black <gabeblack@google.com>
Commit-Ready: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When secure booting is chosen:
* The u-boot shell is never invoked during boot--we just do a simple
table lookup to find the command. This means we could even remove
the shell parsing from u-boot and still be able to boot.
* The boot command can't be interruped.
* Failure doesn't cause us to fall back to the shell.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This change adds a call to set_working_fdt_addr near the end of u-boot
initialization which tells the fdt command/library where the device tree is.
This makes it possible to use the fdt command to look at the active device tree
since otherwise there would be no way to know what address it was at to set
things up manually.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Load boot command from /config/bootcmd of device tree if present.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
commit 199adb601f "common/misc: sparse
fixes" broke the help command trying to fix the sparse error
"command.c:44:38: error: bad constant expression".
As Henrik points out, the fix was bad because the commit used
CONFIG_SYS_MAXARGS whereas the code intended to use the maximum
number of commands (not arguments to a command).
Revert command.c changes to the original code as asked by Wolfgang.
Reported-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add support for drawing compressed RLE8 bitmaps.
Reference: http://www.digicamsoft.com/bmp/bmp.html
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Che-Liang Chiou <clchiou@chromium.org>
[agust: fix some minor style issues and build warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This change fixed 2 things:
- Rename padded_line to padded_width since it is (width + padded_row) not line.
- When finished a line, should skip the padded_row that is
(padded_width - width) instead of (width - padded_width).
Reference: http://en.wikipedia.org/wiki/BMP_file_format
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a basic API to provide access to lcd parameters such as screen
size, and to position the cursor on the screen.
This matches up with the video API for the same purpose. Unfortunately
they are not yet combined.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a basic API to provide access to video parameters such as screen
size, and to position the cursor on the screen. Also add a prototype
for video_display_bitmap() which was missing.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?
Note: in the ping.c fix, commit a36b12f95a
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
command.c:44:38: error: bad constant expression
dlmalloc.c:1468:2: warning: Using plain integer as NULL pointer
dlmalloc.c:1468:5: warning: Using plain integer as NULL pointer
dlmalloc.c:2176:12: warning: Using plain integer as NULL pointer
dlmalloc.c:2179:31: warning: Using plain integer as NULL pointer
dlmalloc.c:2382:14: warning: Using plain integer as NULL pointer
dlmalloc.c:2436:14: warning: Using plain integer as NULL pointer
dlmalloc.c:2582:31: warning: Using plain integer as NULL pointer
dlmalloc.c:2585:17: warning: Using plain integer as NULL pointer
dlmalloc.c:2646:14: warning: Using plain integer as NULL pointer
dlmalloc.c:2659:19: warning: Using plain integer as NULL pointer
dlmalloc.c:2692:19: warning: Using plain integer as NULL pointer
dlmalloc.c:2707:19: warning: Using plain integer as NULL pointer
dlmalloc.c:2708:14: warning: Using plain integer as NULL pointer
dlmalloc.c:2786:31: warning: Using plain integer as NULL pointer
dlmalloc.c:2801:12: warning: Using plain integer as NULL pointer
dlmalloc.c:2801:22: warning: Using plain integer as NULL pointer
dlmalloc.c:2926:27: warning: Using plain integer as NULL pointer
dlmalloc.c:2928:14: warning: Using plain integer as NULL pointer
dlmalloc.c:2929:12: warning: Using plain integer as NULL pointer
dlmalloc.c:3075:14: warning: Using plain integer as NULL pointer
hush.c:292:14: warning: symbol 'last_return_code' was not declared. Should it be static?
hush.c:293:5: warning: symbol 'nesting_level' was not declared. Should it be static?
hush.c:2175:20: warning: Using plain integer as NULL pointer
hush.c:2175:34: warning: Using plain integer as NULL pointer
hush.c:2210:41: warning: Using plain integer as NULL pointer
hush.c:2216:45: warning: Using plain integer as NULL pointer
hush.c:2249:25: warning: Using plain integer as NULL pointer
hush.c:2332:13: warning: symbol 'new_pipe' was not declared. Should it be static?
hush.c:2390:5: warning: symbol 'reserved_word' was not declared. Should it be static?
hush.c:2927:5: warning: symbol 'parse_stream' was not declared. Should it be static?
hush.c:3127:6: warning: symbol 'mapset' was not declared. Should it be static?
hush.c:3133:6: warning: symbol 'update_ifs_map' was not declared. Should it be static?
hush.c:3161:5: warning: symbol 'parse_stream_outer' was not declared. Should it be static?
hush.c:3295:34: warning: Using plain integer as NULL pointer
hush.c:3631:5: warning: symbol 'do_showvar' was not declared. Should it be static
image.c:1282:29: warning: Using plain integer as NULL pointer
image.c:1315:41: warning: Using plain integer as NULL pointer
image.c:1330:25: warning: Using plain integer as NULL pointer
image.c:1706:25: warning: Using plain integer as NULL pointer
main.c:510:10: warning: symbol 'hist_num' was not declared. Should it be static?
main.c:512:5: warning: symbol 'hist_list' was not declared. Should it be static?
main.c:513:6: warning: symbol 'hist_lines' was not declared. Should it be static?
usb_storage.c:195:6: warning: symbol 'usb_show_progress' was not declared. Should it be static?
usb_storage.c:440:48: warning: Using plain integer as NULL pointer
usb_storage.c:503:5: warning: symbol 'usb_stor_BBB_comdat' was not declared. Should it be static?
usb_storage.c:551:5: warning: symbol 'usb_stor_CB_comdat' was not declared. Should it be static?
usb_storage.c:629:55: warning: Using plain integer as NULL pointer
usb_storage.c:620:5: warning: symbol 'usb_stor_CBI_get_status' was not declared. Should it be static?
usb_storage.c:675:43: warning: Using plain integer as NULL pointer
usb_storage.c:668:5: warning: symbol 'usb_stor_BBB_clear_endpt_stall' was not declared. Should it be static?
usb_storage.c:679:5: warning: symbol 'usb_stor_BBB_transport' was not declared. Should it be static?
usb_storage.c:801:5: warning: symbol 'usb_stor_CB_transport' was not declared. Sh
xyzModem.c:104:1: warning: symbol 'CYGACC_COMM_IF_GETC_TIMEOUT' was not declared. Should it be static?
xyzModem.c:122:1: warning: symbol 'CYGACC_COMM_IF_PUTC' was not declared. Should it be static?
xyzModem.c:169:1: warning: symbol 'parse_num' was not declared. Should it be stat
note: hush.c's nesting_level deleted because not used.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
cmd_boot.c:40:5: warning: symbol 'do_go' was not declared. Should it be static?
cmd_bootm.c:164:6: warning: symbol '__arch_preboot_os' was not declared. Should it be static?
cmd_bootm.c:477:5: warning: symbol 'do_bootm_subcommand' was not declared. Should it be static?
cmd_bootm.c:1022:1: error: directive in argument list
cmd_bootm.c:1028:1: error: directive in argument list
cmd_bootm.c:1029:1: error: directive in argument list
cmd_bootm.c:1036:1: error: directive in argument list
cmd_bootm.c:1042:1: error: directive in argument list
cmd_bootm.c:1044:1: error: directive in argument list
cmd_bootm.c:1045:1: error: directive in argument list
cmd_bootm.c:1047:1: error: directive in argument list
cmd_bootm.c:1089:5: warning: symbol 'do_iminfo' was not declared. Should it be static?
cmd_bootm.c:1176:5: warning: symbol 'do_imls' was not declared. Should it be static?
cmd_bootm.c:1654:1: error: directive in argument list
cmd_bootm.c:1660:1: error: directive in argument list
cmd_console.c:32:5: warning: symbol 'do_coninfo' was not declared. Should it be s
cmd_date.c:46:5: warning: symbol 'do_date' was not declared. Should it be static?
cmd_echo.c:27:5: warning: symbol 'do_echo' was not declared. Should it be static?
cmd_exit.c:27:5: warning: symbol 'do_exit' was not declared. Should it be static?
cmd_fat.c:97:5: warning: symbol 'do_fat_ls' was not declared. Should it be static?
cmd_fat.c:136:5: warning: symbol 'do_fat_fsinfo' was not declared. Should it be s
cmd_fdt.c:66:5: warning: symbol 'do_fdt' was not declared. Should it be static?
cmd_fdt.c:542:43: warning: incorrect type in assignment (different base types)
cmd_fdt.c:542:43: expected unsigned int [unsigned] [usertype] <noident>
cmd_fdt.c:542:43: got restricted __be32 [usertype] <noident>
cmd_fdt.c:679:42: warning: cast to restricted __be32
cmd_fdt.c:820:1: error: directive in argument list
cmd_fdt.c:822:1: error: directive in argument list
cmd_flash.c:292:5: warning: symbol 'do_flinfo' was not declared. Should it be static?
cmd_flash.c:324:5: warning: symbol 'do_flerase' was not declared. Should it be static?
cmd_flash.c:457:5: warning: symbol 'do_protect' was not declared. Should it be st
cmd_help.c:27:5: warning: symbol 'do_help' was not declared. Should it be static?
cmd_i2c.c:136:6: warning: symbol '__def_i2c_init_board' was not declared. Should it be static?
cmd_i2c.c:144:14: warning: symbol '__def_i2c_get_bus_speed' was not declared. Should it be static?
cmd_i2c.c:151:5: warning: symbol '__def_i2c_set_bus_speed' was not declared. Should it be static?
cmd_i2c.c:1322:1: error: directive in argument list
cmd_i2c.c:1324:1: error: directive in argument list
cmd_i2c.c:1326:1: error: directive in argument list
cmd_i2c.c:1328:1: error: directive in argument list
cmd_i2c.c:1337:1: error: directive in argument list
cmd_i2c.c:1339:1: error: directive in argument list
cmd_irq.c:27:5: warning: symbol 'do_interrupts' was not declared. Should it be static?
cmd_itest.c:133:5: warning: symbol 'binary_test' was not declared. Should it be static?
cmd_itest.c:158:5: warning: symbol 'do_itest' was not declared. Should it be stat
cmd_load.c:54:5: warning: symbol 'do_load_serial' was not declared. Should it be static?
cmd_load.c:431:6: warning: symbol 'his_eol' was not declared. Should it be static?
cmd_load.c:432:6: warning: symbol 'his_pad_count' was not declared. Should it be static?
cmd_load.c:433:6: warning: symbol 'his_pad_char' was not declared. Should it be static?
cmd_load.c:434:6: warning: symbol 'his_quote' was not declared. Should it be static?
cmd_load.c:436:5: warning: symbol 'do_load_serial_bin' was not declared. Should it be static?
cmd_load.c:549:6: warning: symbol 'send_pad' was not declared. Should it be static?
cmd_load.c:558:6: warning: symbol 'ktrans' was not declared. Should it be static?
cmd_load.c:568:5: warning: symbol 'chk1' was not declared. Should it be static?
cmd_load.c:578:6: warning: symbol 's1_sendpacket' was not declared. Should it be static?
cmd_load.c:587:6: warning: symbol 'send_ack' was not declared. Should it be static?
cmd_load.c:600:6: warning: symbol 'send_nack' was not declared. Should it be static?
cmd_load.c:614:6: warning: symbol 'os_data_init' was not declared. Should it be static?
cmd_load.c:615:6: warning: symbol 'os_data_char' was not declared. Should it be static?
cmd_load.c:657:6: warning: symbol 'k_data_init' was not declared. Should it be static?
cmd_load.c:663:6: warning: symbol 'k_data_save' was not declared. Should it be static?
cmd_load.c:669:6: warning: symbol 'k_data_restore' was not declared. Should it be static?
cmd_load.c:675:6: warning: symbol 'k_data_char' was not declared. Should it be static?
cmd_load.c:693:6: warning: symbol 'send_parms' was not declared. Should it be static?
cmd_load.c:694:6: warning: symbol 'send_ptr' was not declared. Should it be static?
cmd_load.c:698:6: warning: symbol 'handle_send_packet' was not declared. Should i
cmd_mdio.c:60:5: warning: symbol 'mdio_write_ranges' was not declared. Should it be static?
cmd_mdio.c:82:5: warning: symbol 'mdio_read_ranges' was not declared. Should it be static?
cmd_mdio.c:115:5: warning: symbol 'extract_reg_range' was not declared. Should it be static?
cmd_mdio.c:144:5: warning: symbol 'extract_phy_range' was not declared. Should it
cmd_mem.c:54:5: warning: symbol 'do_mem_md' was not declared. Should it be static?
cmd_mem.c:150:5: warning: symbol 'do_mem_mm' was not declared. Should it be static?
cmd_mem.c:154:5: warning: symbol 'do_mem_nm' was not declared. Should it be static?
cmd_mem.c:159:5: warning: symbol 'do_mem_mw' was not declared. Should it be static?
cmd_mem.c:256:5: warning: symbol 'do_mem_cmp' was not declared. Should it be static?
cmd_mem.c:326:5: warning: symbol 'do_mem_cp' was not declared. Should it be static?
cmd_mem.c:436:5: warning: symbol 'do_mem_base' was not declared. Should it be static?
cmd_mem.c:449:5: warning: symbol 'do_mem_loop' was not declared. Should it be static?
cmd_mem.c:595:5: warning: symbol 'do_mem_mtest' was not declared. Should it be static?
cmd_mem.c:618:26: warning: Using plain integer as NULL pointer
cmd_mem.c:1057:5: warning: symbol 'do_mem_crc' was not declared. Should it be static?
cmd_misc.c:30:5: warning: symbol 'do_sleep' was not declared. Should it be static
cmd_mmc.c:118:5: warning: symbol 'do_mmcinfo' was not declared. Should it be static?
cmd_mmc.c:272:32: warning: Using plain integer as NULL pointer
cmd_mmc.c:150:5: warning: symbol 'do_mmcops' was not declared. Should it be stati
cmd_mp.c:27:1: warning: symbol 'cpu_cmd' was not declared. Should it be static?
cmd_mp.c:85:1: error: directive in argument list
cmd_mp.c:88:1: error: directive in argument list
cmd_mtdparts.c:150:18: warning: symbol 'mtdids' was not declared. Should it be static?
cmd_mtdparts.c:153:18: warning: symbol 'devices' was not declared. Should it be static?
cmd_mtdparts.c:713:5: warning: symbol 'mtd_device_validate' was not declared. Should it be static?
cmd_mtdparts.c:1887:5: warning: symbol 'do_chpart' was not declared. Should it be static?
cmd_mtdparts.c:1925:5: warning: symbol 'do_mtdparts' was not declared. Should it be static?
cmd_mtdparts.c:2060:1: error: directive in argument list
cmd_mtdparts.c:2063:1: error: directive in argument list
cmd_mtdparts.c:2066:1: error: directive in argument list
cmd_mtdparts.c:2071:1: error: directive in argument list
cmd_mtdparts.c:2073:1: error: directive in argument list
cmd_nand.c:377:18: error: bad constant expression
cmd_nand.c:431:5: warning: symbol 'do_nand' was not declared. Should it be static?
cmd_nand.c:796:1: error: directive in argument list
cmd_nand.c:801:1: error: directive in argument list
cmd_nand.c:802:1: error: directive in argument list
cmd_nand.c:806:1: error: directive in argument list
cmd_nand.c:819:1: error: directive in argument list
cmd_nand.c:824:1: error: directive in argument list
cmd_nand.c:825:1: error: directive in argument list
cmd_nand.c:831:1: error: directive in argument list
cmd_nand.c:918:5: warning: symbol 'do_nandboot' was not declared. Should it be static?
cmd_net.c:33:5: warning: symbol 'do_bootp' was not declared. Should it be static?
cmd_net.c:107:5: warning: symbol 'do_dhcp' was not declared. Should it be static?
cmd_net.c:120:5: warning: symbol 'do_nfs' was not declared. Should it be static?
cmd_nvedit.c:138:5: warning: symbol 'do_env_print' was not declared. Should it be static?
cmd_nvedit.c:323:5: warning: symbol '_do_env_set' was not declared. Should it be static?
cmd_nvedit.c:435:5: warning: symbol 'do_env_set' was not declared. Should it be static?
cmd_nvedit.c:514:5: warning: symbol 'do_env_edit' was not declared. Should it be static?
cmd_nvedit.c:620:5: warning: symbol 'do_env_save' was not declared. Should it be static?
cmd_nvedit.c:1016:1: error: directive in argument list
cmd_nvedit.c:1018:1: error: directive in argument list
cmd_nvedit.c:1021:1: error: directive in argument list
cmd_nvedit.c:1023:1: error: directive in argument list
cmd_nvedit.c:1024:1: error: directive in argument list
cmd_nvedit.c:1026:1: error: directive in argument list
cmd_nvedit.c:1027:1: error: directive in argument list
cmd_nvedit.c:1029:1: error: directive in argument list
cmd_nvedit.c:1030:1: error: directive in argument list
cmd_nvedit.c:1032:1: error: directive in argument list
cmd_nvedit.c:1034:1: error: directive in argument list
cmd_nvedit.c:1036:1: error: directive in argument list
cmd_nvedit.c:1037:1: error: directive in argument list
cmd_nvedit.c:1039:1: error: directive in argument list
cmd_pci.c:38:17: warning: symbol 'ShortPCIListing' was not declared. Should it be static?
cmd_pci.c:38:22: warning: 'ShortPCIListing' defined but not used [-Wunused-variable]
cmd_pci.c:411:5: warning: symbol 'do_pci' was not declared. Should it be static?
cmd_pci.c:494:1: error: directive in argument list
cmd_pci.c:497:1: error: directive in argument list
cmd_reginfo.c:40:5: warning: symbol 'do_reginfo' was not declared. Should it be static?
cmd_sata.c:31:5: warning: symbol 'sata_curr_device' was not declared. Should it be static?
note -> ata_piix.c doesn't seem to use 'sata_curr_device'; deleted.
cmd_sata.c:32:18: warning: symbol 'sata_dev_desc' was not declared. Should it be static?
cmd_sata.c:70:5: warning: symbol 'do_sata' was not declared. Should it be static?
cmd_setexpr.c:53:5: warning: symbol 'do_setexpr' was not declared. Should it be static?
cmd_source.c:186:1: error: directive in argument list
cmd_source.c:190:1: error: directive in argument list
cmd_test.c:27:5: warning: symbol 'do_test' was not declared. Should it be static?
cmd_test.c:153:5: warning: symbol 'do_false' was not declared. Should it be static?
cmd_test.c:164:5: warning: symbol 'do_true' was not declared. Should it be static
cmd_usb.c:43:6: warning: symbol 'usb_get_class_desc' was not declared. Should it be static?
cmd_usb.c:69:6: warning: symbol 'usb_display_class_sub' was not declared. Should it be static?
cmd_usb.c:151:6: warning: symbol 'usb_display_string' was not declared. Should it be static?
cmd_usb.c:161:6: warning: symbol 'usb_display_desc' was not declared. Should it be static?
cmd_usb.c:195:6: warning: symbol 'usb_display_conf_desc' was not declared. Should it be static?
cmd_usb.c:210:6: warning: symbol 'usb_display_if_desc' was not declared. Should it be static?
cmd_usb.c:227:6: warning: symbol 'usb_display_ep_desc' was not declared. Should it be static?
cmd_usb.c:252:6: warning: symbol 'usb_display_config' was not declared. Should it be static?
cmd_usb.c:283:6: warning: symbol 'usb_show_tree_graph' was not declared. Should it be static?
cmd_usb.c:343:6: warning: symbol 'usb_show_tree' was not declared. Should it be static?
cmd_usb.c:356:5: warning: symbol 'do_usbboot' was not declared. Should it be static?
cmd_usb.c:366:5: warning: symbol 'do_usb' was not declared. Should it be static?
cmd_version.c:31:5: warning: symbol 'do_version' was not declared. Should it be s
cmd_ximg.c:46:1: warning: symbol 'do_imgextract' was not declared. Should it be static?
cmd_ximg.c:272:1: error: directive in argument list
cmd_ximg.c:276:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When the generic filesystem load command "fsload" was written, I felt
that "load" was too generic of a name for it, since many other similar
commands already existed. However, it turns out that there is already
an "fsload" command, so that name cannot be used. Rename the new
"fsload" to plain "load" to avoid the conflict. At least anyone who's
used a Basic interpreter should feel familiar with the name!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 045fa1e "fs: add filesystem switch libary, implement ls and
fsload commands" unified the implementation of fatload and ext*load
with the new command fsload. However, this altered the interpretation
of command-line numbers from always being base-16, to requiring a "0x"
prefix for base-16 numbers. Enhance do_fsload() to allow commands to
specify which base to use.
Use base 0, thus requiring a "0x" prefix for the new fsload command.
This feels much cleaner than assuming base 16.
Use base 16 for the pre-existing fatload and ext*load to prevent a
change in behaviour.
Use base 16 exclusively for the loadaddr environment variable, since
that variable is interpreted in multiple places, so we don't want the
behaviour to change.
Update command help text to make it clear where numbers are assumed to
be hex, and where an explicit "0x" prefix is required.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
TABs in the help text won't line up in the same place on the console as
in a source editor. Replace them with spaces to make ensuring correct
alignment easier.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The prototypes in the header were changed by commit 4ac8f8e0 but the
functions no longer match. Correct this.
It seems odd that block devices take an lbaint_t for the block count, but
an unsigned long for the blknr. Surely we should promote blknr to lbaint_t
also?
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add a new function to find out the number of available SCSI disks. Also
set the 'scsidevs' environment variable after each scan.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement write functionality in the scsi layer. A ''scsi write'
command is also added to console for testing.
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Many AHCI controllers are identical, the main (and often the
only) difference being the PCI Vendor ID/Device ID combination
reported by the device.
This change allows the config file to define a list of PCI vendor
ID/device ID pairs. The driver would scan the list and initialize
the first device it finds.
No actual multiple device list is introduced yet, this change
just add the framework.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch fixes the following compile warnings:
cmd_zfs.c:177:1: warning: initialization from incompatible pointer type [enabled by default]
cmd_zfs.c:177:1: warning: (near initialization for '_u_boot_list_cmd_zfsls.cmd') [enabled by default]
cmd_zfs.c:182:1: warning: initialization from incompatible pointer type [enabled by default]
cmd_zfs.c:182:1: warning: (near initialization for '_u_boot_list_cmd_zfsload.cmd') [enabled by default]
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jorgen Lundman <lundman@lundman.net>
When putting pointers into a format string use %p to ensure that they
are printed correctly regardless of bitsize. This fixes warnings on
sandbox on 64bit systems.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the following error in the ext4 command:
cmd_ext4.c:110:3: error: format '%lu' expects argument of type
'long unsigned int', but argument 4 has type 'int' [-Werror=format]
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement "ls" and "fsload" commands that act like {fat,ext2}{ls,load},
and transparently handle either file-system. This scheme could easily be
extended to other filesystem types; I only didn't do it for zfs because
I don't have any filesystems of that type to test with.
Replace the implementation of {fat,ext[24]}{ls,load} with this new code
too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Remove calls to serial_assign() that are failing now that it returns a
proper error code. This calls were not actually doing anything
because they passed the name of a stdio_dev when a serial_device name
is exptectd.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Change jump_to_image_no_args() to a weak symbol to allow override by
SoC specific code. This is required by tegra because the SPL runs on
a different CPU from the image it is loading, so tegra specific
initialization is required to start the host CPU. Pass in spl_image
as a parameter for the same reason.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove calls to serial_assign() that are failing now that it returns a
proper error code. This calls were not actually doing anything
because they passed the name of a stdio_dev when a serial_device name
is exptectd.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
This makes the FAT filesystem API more consistent with other block-based
filesystems. If in the future standard multi-filesystem commands such as
"ls" or "load" are implemented, having FAT work the same way as other
filesystems will be necessary.
Convert cmd_fat.c to the new API, so the code looks more like other files
implementing the same commands for other filesystems.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This change adds CBFS support and some commands to use it to u-boot. These
commands are:
cbfsinit - Initialize CBFS support and pull all metadata into RAM. The end of
the ROM is an optional parameter which defaults to the standard 0xffffffff and
can be used to support multiple CBFSes in a system. The last one set up with
cbfsinit is the one that will be used.
cbfsinfo - Print information from the CBFS header.
cbfsls - Print out the size, type, and name of all the files in the current
CBFS. Recognized types are translated into symbolic names.
cbfsload - Load a file from CBFS into memory. Like the similar command for fat
filesystems, you can optionally provide a maximum size.
Support for CBFS is compiled in when the CONFIG_CMD_CBFS option is specified.
The CBFS driver can also be used programmatically from within u-boot.
If u-boot needs something out of CBFS very early before the heap is
configured, it won't be able to use the normal CBFS support which caches some
information in memory it allocates from the heap. The
cbfs_file_find_uncached function searches a CBFS instance without touching
the heap.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch converts the old method of creating a list of command
onto the new LG-arrays code. The old u_boot_cmd section is converted
to new u_boot_list_cmd subsection and LG-array macros used as needed.
Minor adjustments had to be made to the common code to work with the
LG-array macros, mostly the fixup_cmdtable() calls are now passed the
ll_entry_start and ll_entry_count instead of linker-generated symbols.
The command.c had to be adjusted as well so it would use the newly
introduced LG-array API instead of directly using linker-generated
symbols.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Implement common bounce buffer to be used on a less capable hardware.
That includes hardware that can not do DMA from any address or such.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a USB configuration descriptor was larger than our USB buffer
(512 bytes), we were skipping the full descriptor reading but then we
were still parsing and using it, triggering memory corruptions.
Now in that case, it just skips this device enumeration and displays the
appropriate message to the user, so he can fix the buffer if he wants.
This bug was triggered by some UVC webcams which have very large
configuration descriptors (e.g. a couple of kB) describing all their
supported video encodings.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
usb_storage wouldn't compile when the CONFIG_SYS_64BIT_LBA option is
turned on because the used fixed size data types in their exported
functions when they should have used lbaint_t for the block count
parameter. That meant that when the sizes happened to be the same, when
using a 28 bit LBA, the driver would build, but when it wasn't, a 48 bit
LBA, things broke.
This change adjusts the signatures to use the right type and makes small
adjustments in the affected functions.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This doesn't need to be a long, so change it.
Also adjust bi_baudrate to be unsigned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
This doesn't need to be a long, so change it.
Also adjust bi_baudrate to be unsigned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
This doesn't need to be a long, so change it.
Also adjust bi_baudrate to be unsigned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
This does not need to be a long, so change it.
Also adjust bi_baudrate to be unsigned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
These don't need to be longs, so change them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Tom Rini <trini@ti.com>
There used to be a huge structure duplicated 3 times in the source.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Make ide_led() a weak alias instead of global/local function/empty macro
based on CONFIG_IDE_LED value and/or board-specific CONFIGs, to get rid of
board-specific code in cmd_ide.c
Define dummy values to get rid of compoler errors in case where ide_led()
used to be an empty macro
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Move input_data() and friends to board/cpc45/ide.c, as overrides for weak
aliases in cmd_ide.c
note: checkpatch emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
This changes input_data() and friends from static function to global symbols
under weak alias, to enable board specific overrides (and therefore get rid of
board-specific code in cmd_ide.c)
Also declare ide_bus_offset in the header file, so other files can use
ATA_CURR_BASE as well.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created
ide_init_postreset() (invoked after calling ide_reset after ide_preinit),
some cleanup to make checkpatch happy, enable IDE init hooks in configs of
affected boards.
confusingly, these hooks are used by more than just mpc8xx-based boards, and
therefore are placed in arch/ppc/lib/
note: checkpatch still emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Allow the use of an I2C address to test and return success
if one or more devices is found.
This allows device presence to alter the flow of a script.
e.g.
if i2c probe 0x04 ; then
echo found Hannstar touch ;
fi
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Allow the itb file to declare to u-boot that its hash should not be
checked automatically on bootm or iminfo. This allows an image to
either be checked automatically or to include a script which may
check it otherwise (such as after part of the itb has been relocated
to RAM by the script).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Scripts in the ITB format will have spaces in them and will end in a
newline charachter. Make sure that these are considered printable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Add commands to access data in the fdt. This allows data from a dtb
or itb to be accessed from the shell scripts.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Prevent printing the entire image in a itb. It is most likely unhelpful
to have the hex of the entire image scroll for minutes on your slow
serial console.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Before this patch, error codes returned from fdtlib were ignored and
continued access would cause a crash. Now just check if the image is
truncated and error if so.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes a warning when compiling with ELDK-5.2.1 for MIPS64:
cmd_bdinfo.c: In function 'print_lnum':
cmd_bdinfo.c:56:2: warning: format '%llX' expects argument of type 'long long unsigned int', but argument 3 has type 'u64' [-Wformat]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Allows to initialize more than one USB controller at once.
v2: print message when controller stop fails
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the common/serial.c into driver/serial/, since this file
provides serial multiplexing functions and it is imperative to
be linked with libserial.o instead of libcommon.o.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
If case the get_current() call fails before relocation, the U-Boot
must try to print an error message, fail and either reset or halt.
Such error is critical enough to halt the system, as it means the
system is in very bad state.
This is now also used in SPL, since CONFIG_SERIAL_MULTI is enabled
unconditionally. To avoid compiling whole vsprintf.c into SPL, use
puts() to print error message and hang() to stop the system in case
of SPL build.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sh serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sh driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Phil Edworthy <PHIL.EDWORTHY@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sa1100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sa1100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into s3c44b0 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c44b0 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into pl01x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the pl01x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Mathieu J. Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Implement support for CONFIG_SERIAL_MULTI into netarm serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the netarm driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mxc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mxc driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into max3100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the max3100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into lpc2292 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc2292 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into lh7a40x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lh7a40x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into ks8695 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ks8695 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into ixp serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ixp driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Schwingen <michael@schwingen.org>
Implement support for CONFIG_SERIAL_MULTI into imx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the imx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into clps7111 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the clps7111 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sandbox serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sandbox driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Implement support for CONFIG_SERIAL_MULTI into s3c64xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c64xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Implement support for CONFIG_SERIAL_MULTI into s3c4510b serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c4510b driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into OpenCores serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the OpenCores driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott McNutt <smcnutt@psyent.com>
Implement support for CONFIG_SERIAL_MULTI into ns9750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ns9750 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into MCF serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the MCF driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: TsiChung Liew <tsicliew@gmail.com>
Implement support for CONFIG_SERIAL_MULTI into lpc32xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc32xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Implement support for CONFIG_SERIAL_MULTI into atmel serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the atmel driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Xu, Hong <Hong.Xu@atmel.com>
Implement support for CONFIG_SERIAL_MULTI into altera serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott McNutt <smcnutt@psyent.com>
Implement support for CONFIG_SERIAL_MULTI into altera_jtag serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera_jtag driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Implement support for CONFIG_SERIAL_MULTI into p3mx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the p3mx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into sconsole serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sconsole driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into ml2 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ml2 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into evb64260 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the evb64260 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into cpci750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the cpci750 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into cogent serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the cogent driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into bmw serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the bmw driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into amirix serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the amirix driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into marvell serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the marvell driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into leon3 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the leon3 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Implement support for CONFIG_SERIAL_MULTI into leon2 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the leon2 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the iop480 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc85xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260
serial drivers. These drivers were so far only usable directly, but this
patch also adds support for the multi method. This allows using more than
one serial driver alongside the mpc8260 drivers. Also, add a weak
implementation of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc8220 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc5xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Implement support for CONFIG_SERIAL_MULTI into JZ serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the JZ driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Implement support for CONFIG_SERIAL_MULTI into asc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the asc driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Implement support for CONFIG_SERIAL_MULTI into au1x00 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the au1x00 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Rework the emulation of serial console via JTAG from simple ad-hoc
implementation of serial port routines to CONFIG_SERIAL_MULTI and
enable CONFIG_SERIAL_MULTI unconditionally for blackfin.
In order for the JTAG serial console to take precedence over all
other serial ports available in system, implement override for
default_serial_console call returning this JTAG serial console.
This brings in a bit of a growth of size, but eventually will allow
us to unconditionally enable CONFIG_SERIAL_MULTI throughout the whole
U-Boot and maintain only one serial subsystem.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Rename the serial_register_bfin_uart() to bfin_initialize_serial()
to be consistent with the rest of the naming. Next, remove it's
prototype from serial.h and properly insert it into serial.c as
the rest of the serial initialization functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Move the registration of eserialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented ns16550_serial_initialize() function, which is
implemented inside of the ns16550 serial driver allows encapsulation
of eserialN_device within the ns16550 serial driver itself.
Also, remove the exports of eserialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the ns16550 serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented mpc512x_serial_initialize() function, which is
implemented inside of the mpc512x serial driver allows encapsulation
of serialN_device within the mpc512x serial driver itself.
Also, remove the exports of serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the mpx512x serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of xuartlite_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented xuartlite_serial_initialize() function, which is
implemented inside of the serial_xuartlite driver allows encapsulation
of xuartlite_serialN_device within the serial_xuartlite driver itself.
Also, remove the exports of xuartlite_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_xuartlite driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of zynq_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented zynq_serial_initialize() function, which is
implemented inside of the serial_zynq driver allows encapsulation
of zynq_serialN_device within the serial_zynq driver itself.
Also, remove the exports of zynq_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_zynq driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Tom Rini <trini@ti.com>
Move the registration of s5p_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s5p_serial_initialize() function, which is
implemented inside of the serial_s5p driver allows encapsulation
of s5p_serialN_device within the serial_s5p driver itself.
Also, remove the exports of s5p_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s5p driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Move the registration of serial_XXuart ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented pxa_serial_initialize() function, which is
implemented inside of the serial_pxa driver allows encapsulation
of serial_XXuart within the serial_pxa driver itself.
Also, remove the exports of serial_XXuart from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_pxa driver and
the default console is picked by CONFIG_CONS_IDX macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the registration of s3c24xx_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s3c24xx_serial_initialize() function, which is
implemented inside of the serial_s3c24xx driver allows encapsulation
of s3c24xx_serialN_device within the serial_s3c24xx driver itself.
Also, remove the exports of s3c24xx_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s3c24xx driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: C Nauman <cnauman@diagraph.com>
Move the registration of serial_smc and serial_scc ports from
default serial_initialize() into CPU specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The exports of both serial_scc_device and serial_smc_device can
not yet be removed as they are still used in default_serial_console()
calls.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
This macro simplifies declaration of weak aliases for per-driver
functions, which register these drivers with the serial subsystem.
The idea here is to push serial_register() calls from serial.c into
the drivers. To avoid pile of ifdef construct as it is now, create
weak aliases to these functions, which in case the driver is not
present alias onto an empty function, which is in turn optimized out
altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Rename .init() to .start() and .uninit() to .stop() in struct
serial_device. This allows aligning struct serial_device with
closer to struct stdio_dev. The real goal here is to allow
these two structures to converge together and eventually make
one to be a superset of the other.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Kill multiple occurances and redeclaration of MK_STR
in favor of __stringify().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
We have not strictly speaking relocated at this point, do not claim that
we have. This is not required for output.
Signed-off-by: Tom Rini <trini@ti.com>
This fixes warnings when compiling with ELDK-5.2.1 for MIPS64:
cmd_elf.c: In function 'load_elf_image_phdr':
cmd_elf.c:289:15: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
cmd_elf.c: In function 'load_elf_image_shdr':
cmd_elf.c:343:12: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
cmd_elf.c:346:12: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[Tom: Move valid_elf_image around and don't mark it as static as another
board makes use of this function]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
env default -a -f calls env_check_apply on all existing environment
variables with a NULL value for "newval" as a way of cleaning up.
This causes string manipulation functions to crash on most architectures.
So replace a NULL argument with an empty string.
Reported-By: Stefano Babic <sbabic@denx.de>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Instead of referenceing the source webpage (which can change) include
the license in the source file.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The driver is used on Xilinx Zynq platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Change echo to puts characters together where it knows about them
together. This improves netconsole performance by greatly reducing
the number of packets that are sent.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Two sub-commands... start and get.
* start sets the reference.
* get prints out the time since the last start (in "<sec>.<msec>" format).
If get is called without start, returns time since boot.
Simple way to benchmark an operation: "timer start;<commands-to-measure>;timer get"
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This allows you to read ini-formatted data from anywhere and then
import one of the sections into the environment
This is based on rev 16 at http://code.google.com/p/inih/
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Add a parameter that allows you to store the md5 sum to either a
memory location or a variable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Loosely based on CONFIG_CRC32_VERIFY.
The sum to verify against can be in memory, in a variable, or the last
parameter to the function directly.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Add a parameter that allows you to store the SHA1 sum to either a
memory location or a variable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Loosely based on CONFIG_CRC32_VERIFY.
The sum to verify against can be in memory, in a variable, or the last
parameter to the function directly.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Improve debug output for test by indicating the number of parameters
and quoting the parameters to make it clear exactly what each contains
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Define the new "-2" value for bootdelay to mean autoboot with no delay
and don't check for an abort key (while "0" value means do check).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Now that there are a few features, add a bootstage command to access them.
bootstage report - prints a report
bootstage stash/unstash - stashes bootstage records in memory, reads them back
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to write the bootstage information to memory for
use by a later utility, or the Linux kernel. Provide a function to do
this as well as a function to read bootstage information back and incorporate
it into the current table.
This also makes it possible for U-Boot to chain to another U-Boot and pass
on its bootstage information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option, CONFIG_BOOTSTAGE_FDT to pass boot timings to the kernel
in the device tree, if available. To use this, you must have
CONFIG_OF_LIBFDT defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we want to add up the amount of time spent in a particular
activity when it is happening in a number of discrete chunks.
Add bootstage_start() to mark the start of an acitivity and
bootstage_accum() to accumulate the time since the last start. Calling
these function in pairs results in the accumulated time being collected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not static, but not exported either. Add a prototype
in the header file and move the required enum to the header also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
Commit cfda5aeab8
(cmd_fat: use common get_device_and_partition function)
introduced a warning:
cmd_fat.c: In function 'do_fat_fswrite':
cmd_fat.c:178:8: warning: unused variable 'ep' [-Wunused-variable]
Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
First, remove the puts from the case where we don't have an mkimage
header as this is somewhat common and intentional for no-arg target
images. Second, rework the final switch statement in board_init_r to,
in the case of !CONFIG_SPL_OS_BOOT be only about doing debug prints
about if we know what the magic is or not (the CONFIG_SPL_OS_BOOT case
is unchanged). Then we call jump_to_image_no_args(). This gives us the
same behavior as before but with slightly smaller code.
Signed-off-by: Tom Rini <trini@ti.com>
By setting CONFIG_SYS_UBOOT_START boards can now use a different entry
point for their U-Boot image. So the U-Boot entry point is not fixed
to CONFIG_SYS_TEXT_BASE any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
On some system (e.g. powerpc), the load-address and entry-point is
located at address 0. So the current approach to load the image
(payload) including the header to the address "load-address - 64"
can't work here.
This patch adds an flag to skip this copying including header to
the SPL framework. By setting SPL_COPY_PAYLOAD_ONLY, only the
playload will be copied. This will be used by the SPL NOR flash
driver on powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
SPL NOR flash booting support is quite simple. Only copying of the
images is needed.
On MPC5xxx we need to make sure to only use the standard memcpy()
implementation and not the MPC5xxx specific one. As the MPC5xxx
version has some complexity which is not needed for this SPL
booting.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Now DT support is becoming common for all new SoC's. Hence it is better
to have option for getting specific FDT from the remote server.
This patch adds support for new label i.e. 'fdt'. This will allow to
retrieve 'fdt blob' from the remote server. This patch take care for
the following scenarios.
The usage of fdt is optional.
The 'fdt blob' can be retrieved from tftp or can be available locally
or can be absent.
If 'fdt_addr_r' environment variable is set and 'fdt' label is defined
retrieve 'fdt blob' from tftp. 'fdt_addr_r' is then passed along bootm
command.
If 'fdt_addr' is set and 'fdt blob' is not retrieved from the tftp pass
'fdt_addr' to bootm command. In this case 'fdt blob' will be available
at 'fdt_addr'.
If 'fdt_addr' is not set and 'fdt blob' is not retrieve from tftp pass
NULL to boot command. In this case 'fdt blob' is not required and absent.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
We move the spl_nand_load_image function to common/spl. This will allow
for easier integration of SPL-boots-Linux code on other arches.
Signed-off-by: Tom Rini <trini@ti.com>
If an u-boot image is not found, SPL thinks to load a bare
u-boot.bin image with a maximum size of 200KB.
Use CONFIG_SYS_MONITOR_LEN instead.
Signed-off-by: Stefan Roese <stefan.roese@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
When storage devices contain files larger than the embedded RAM, it is
useful to be able to read these files by chunks, e.g. for a software
update to the embedded NAND Flash from an external storage device (USB
stick, SD card, etc.).
Hence, this patch makes it possible by adding a new FAT API to read
files from a given position. This patch also adds this feature to the
fatload command.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
env_fat and env_remote have an implementation of env_get_char_spec()
function that is not different than the default.
Remove the duplicated code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This implements the following:
part uuid mmc 0:1
-> print partition UUID
part uuid mmc 0:1 uuid
-> set environment variable to partition UUID
part list mmc 0
-> list the partitions on the specified device
"part uuid" can be useful when writing a bootcmd which searches all
known devices for something bootable, and then wants the kernel to
use the same partition as the root device, e.g.:
part uuid ${devtype} ${devnum}:${rootpart} uuid
setenv bootargs root=PARTUUID=${uuid} ...
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Rework get_device_and_partition() to:
a) Implement a new partition ID of "auto", which requests that U-Boot
search for the first "bootable" partition, and fall back to the first
valid partition if none is found. This way, users don't need to
specify an explicit partition in their commands.
b) Make use of get_device().
c) Add parameter to indicate whether returning a whole device is
acceptable, or whether a partition is mandatory.
d) Make error-checking of the user's device-/partition-specification
more complete. In particular, if strtoul() doesn't convert all
characters, it's an error rather than just ignored.
The resultant device/partition returned by the function will be as
follows, based on whether the disk has a partition table (ptable) or not,
and whether the calling command allows the whole device to be returned
or not.
(D and P are integers, P >= 1)
D
D:
No ptable:
!allow_whole_dev: error
allow_whole_dev: device D
ptable:
device D partition 1
D:0
!allow_whole_dev: error
allow_whole_dev: device D
D:P
No ptable: error
ptable: device D partition P
D:auto
No ptable:
!allow_whole_dev: error
allow_whole_dev: device D
ptable:
first partition in device D with bootable flag set.
If none, first valid paratition in device D.
Note: In order to review this patch, it's probably easiest to simply
look at the file contents post-application, rather than reading the
patch itself.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[swarren: Rob implemented scanning for bootable partitions. I fixed a
couple of issues there, switched the syntax to ":auto", added the
error-checking rework, and ":0" syntax for the whole device]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Convert reiserload and reiserls to use common device and partition parsing
function. With the common function "dev:part" can come from the
environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Convert zfsload and zfsls to use common device and partition parsing
function. With the common function "dev:part" can come from the
environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Convert fatload, fatls, and fatinfo to use common device and partition
parsing function. With the common function "dev:part" can come from the
environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Convert ext2/4 load, ls, and write functions to use common device and
partition parsing function. With the common function "dev:part" can come
from the environment and a '-' can be used in that case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
All the raw block load commands duplicate the same code. Starting with
the ide version as it has progress updates convert ide, usb, and scsi boot
commands to all use a common version.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Previously u-boot would initialize the network interface for every
network operation and then shut it down again. This makes sense for
most operations where the network in not known to be needed soon after
the operation is complete. In the case of netconsole, it will use the
network for every interaction with the shell or every printf. This
means that the network is being reinitialized very often. On many
devices, this intialization is very slow.
This patch checks for consecutive netconsole actions and leaves the
ethernet hardware initialized between them. It will still behave the
same old way for all other network operations and any time another
network operation happens between netconsole operations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
If the bmp pointer is null then U-Boot will get stuck when trying
to load the image.
What's worse, it will get stuck before the U-Boot shell becomes
available to the user, thus making it difficult to correct the
situation.
To protect from the above scenario, check if the pointer is valid.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
After further investigation this change is not correct and results in
get_ram_size returning incorrectly large values. Reported first by
Gerlando Falauto.
This reverts commit b8496cced8.
Signed-off-by: Tom Rini <trini@ti.com>
usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.
Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.
v2: fix typo found by Thomas Langer
v3: rebased on top of u-boot-usb/master
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Change the syntax (user API) for "env default":
-f: override write-once variables
var... : accept individual variable(s)
-a: all (resetting the whole env is NOT the default behavior)
Enable variable checking and make changes effective by
enabling do_apply argument to himport_r().
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Change hashtable so that a callback function will decide whether a
variable can be overwritten, and possibly apply the changes.
So add a new field to struct hsearch_data:
o "apply" callback function to check whether a variable can be
overwritten, and possibly immediately apply the changes;
when NULL, no check is performed.
And a new argument to himport_r():
o "do_apply": whether to call the apply callback function
NOTE: This patch does not change the current behavior.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add 2 new arguments to himport_r():
o "nvars", "vars": number and list of variables to take into account
(0 means ALL)
NOTE: This patch does not change the current behaviour.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The logic of checking special parameters (e.g. baudrate, stdin, stdout,
for a valid value and/or whether can be overwritten) and applying the
new value to the running system is now all within a single function
env_check_apply() which can be called whenever changes are made
to the environment, no matter if by set, default or import.
With this patch env_check_apply() is only called by "env set",
retaining previous behavior.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
iomux_doenv() can only return 0 or 1.
So there is no need to save its return value in variable i, as checking
its truth value within an if statement is enough.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The original memory sizing code in get_ram_size clobbers the word
at the base address, but forgets to restore it.
Signed-off-by: Iwo Mergler <Iwo.Mergler@netcommwireless.com>
The third parameter to ALLOC_CACHE_ALIGN_BUFFER is not size (as named),
but rather count (number of elements of the type to allocate). The
current code ends up allocating one copy of env_t for each byte in its
size, which quite possibly ends up overflowing RAM.
This fixes a bug in commit 3801a15 "env_nand: align NAND buffers".
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reported-by: Prabhakar Lad <prabhakar.lad@ti.com>
cmd_bdinfo.c: In function ‘do_bdinfo’:
cmd_bdinfo.c:220:9: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘int’ [-Wformat]
cmd_bdinfo.c:222:9: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘int’ [-Wformat]
cmd_bdinfo.c:224:9: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘int’ [-Wformat]
cmd_bdinfo.c:226:9: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘int’ [-Wformat]
cmd_bdinfo.c:228:9: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘int’ [-Wformat]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: u-boot-dm@lists.denx.de
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
In case the "fdt addr" command wasn't ran yet and any other "fdt"
subcommand was issued, the system crashed due to NULL pointer being
used.
This is caused by "fdt addr" command setting up a pointer to the
FDT memory location. Prior issuing "fdt addr", the pointer is NULL
so calling any other subcommands crashed the u-boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
This fixes the following warnings in dlmalloc seen with my gcc 4.6.
dlmalloc.c: In function 'malloc_bin_reloc':
dlmalloc.c:1493: warning: dereferencing pointer 'p' does break strict-aliasing rules
dlmalloc.c:1493: warning: dereferencing pointer 'p' does break strict-aliasing rules
dlmalloc.c:1490: note: initialized from here
dlmalloc.c:1493: note: initialized from here
This version is tested on avr32 arch boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
eMMC devices may have hardware-level partitions: 2 boot partitions,
up to 4 general partitions, plus the user area. This change introduces
optional config variable CONFIG_SYS_MMC_ENV_PART to indicate which
partition the environment should be stored in: 0=user, 1=boot0, 2=boot1,
4..7=general0..3. This allows the environment to be kept out of the user
area, which simplifies the management of OS-/user-level (MBR/GPT)
partitions within the user area.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In order for cache invalidation and flushing to work properly, the data
and OOB buffers must be aligned to full cache lines.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
eMMC devices may have hardware-level partitions: 2 boot partitions,
up to 4 general partitions, plus the user area. This change introduces
optional config variable CONFIG_SYS_MMC_ENV_PART to indicate which
partition the environment should be stored in: 0=user, 1=boot0, 2=boot1,
4..7=general0..3. This allows the environment to be kept out of the user
area, which simplifies the management of OS-/user-level (MBR/GPT)
partitions within the user area.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Move highly platform dependant code into its own functions to reduce the
number of #ifdefs in lcd_display_bitmap
To avoid breaking the mcc200 board which does not #define
CONFIG_CMD_BMP, this patch also implements bmp_display() for mcc200.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Move highly platform dependant code into its own function to reduce the
number of #ifdefs in the bigger functions
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Simplify lcd_display by centralizing code into a funciton
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Simplify lcd_logo by extracting bmp unzip into its own function.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Check for ctrlc() in operations that take time and loop over the flash
addresses.
In netconsole, tstc() is expensive. Only check once in a while to not
slow down the operation significantly.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When a variable which contains a user-supplied value is dereferenced
(e.g. to be echo'ed), make sure that the value is not further parsed
by hush.
Set the hush local variable "HUSH_NO_EVAL=1" to enable this behavior.
Without this patch, a sequence like this occurs:
Panda # env set my_user_string Bob\'s favorite device
Panda # print my_user_string
my_user_string=Bob's favorite device
Panda # echo $my_user_string
syntax error hush.c:3007
With this patch, it looks like this:
Panda # HUSH_NO_EVAL=1
Panda # env set my_user_string Bob\'s favorite device
Panda # print my_user_string
my_user_string=Bob's favorite device
Panda # echo $my_user_string
Bob's favorite device
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use standard sh syntax:
${VAR:-default}
Use default value: if VAR is set and non-null, expands to $VAR.
Otherwise, expands to default.
${VAR:=default}
Set default value: if VAR is set and non-null, expands to $VAR.
Otherwise, sets hush VAR to default and expands to default.
${VAR:+default}
If VAR is set and non-null, expands to the empty string.
Otherwise, expands to default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This allows cache flush/invalidate operations to succeed on the buffers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This patch adds support to include Load, Entry address and OS tag
of ramdisk on to FIT image through mkimage tool.
Signed-off-by: Jagannadha Sutradharudu Teki <402jagan@gmail.com>
There is a 5-ms delay in usb_stor_BBB_transport, which occurs every 10 kiB of
data for fragmented fatload usb, i.e. roughly 500 ms of delay per MiB. This adds
up to quite a bit of delay if you're loading a large ramdisk.
The purpose of this delay should be to debounce the 5-V/100-mA USB power up.
This patch skips the delay if the device has already been queried as ready.
Signed-off-by: Jim Shimer <mgi2475@motorola.com>
Rework following the review:
- Rebase against the latest u-boot-usb master.
- Replace typedef with #define.
- Use the existing flags struct field instead of adding a new field.
- Remove the setter function.
- Remove the typecasts.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Jim Shimer <mgi2475@motorola.com>
Now that the EHCI driver allocates its qTDs from the heap, the MSC driver is
only limited by the SCSI commands it uses.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
The commit 5dd95cf made the MSC driver EHCI-specific. This patch restores a
basic support of non-EHCI HCDs, like before that commit.
The fallback transfer size is certainly not optimal, but at least it should work
like before.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Support for u-boot's command line command "dfu <interface> <dev> [list]".
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Provides a tool to build boot Image for PBL(Pre boot loader) which is
used on Freescale CoreNet SoCs, PBL can be used to load some instructions
and/or data for pre-initialization. The default output image is u-boot.pbl,
for more details please refer to doc/README.pblimage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.
NOTE: Because the slave can not erase, write master's NOR flash by
PCIE interface, so it can not modify the ENV parameters stored
in master's NOR flash using "saveenv" or other commands.
environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Put the slave's ucode and ENV into it's own memory space.
4. Normally boot from local NOR flash.
5. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the slave module, need to finish these processes:
1. Set the boot location to one PCIE interface by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID of one PCIE for the boot.
4. Set a specific TLB entry in order to fetch ucode and ENV from
master.
5. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
6. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
1. Updated the README.srio-boot-corenet to add descriptions about
boot from PCIE, and change the name to
README.srio-pcie-boot-corenet.
2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
"xxxx_SRIO_PCIE_BOOT", and the image builded with
"xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
from PCIE.
3. Updated other macros and documents if needed to add information
about boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
U-Boot port is based on sources forked from GRUB-0.97 by Sun in 2004,
which can be found here:
http://src.opensolaris.org/source/xref/onnv/onnv-gate/usr/src/grub/grub-0.97/stage2/zfs-include/zfs.h
Released by Sun for GRUB under the license:
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
GRUB official releases include ZFS in version:
ftp://alpha.gnu.org/gnu/grub/grub-1.99~rc1.tar.gz
And patched against GRUB Bazaar repository for ashift fixes (4KB HDDs)
more conveniently found at github:
e7b6ef3ac3
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
This patch updates the yaffs2 in u-boot to correspond to
git://www.aleph1.co.uk/yaffs2
commit id 9ee5d0643e559568dbe62215f76e0a7bd5a63d93
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
When CONFIG_ZERO_BOOTDELAY_CHECK is not defined, bootdelay==0
prevents the check for console input (as stated in README.autoboot).
This must also work in CONFIG_AUTOBOOT_KEYED mode.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Any environment variable can hold commands to be executed by the 'run'
command. The environment variables preboot, bootcmd and menucmd have
special code for triggering execution in certain circumstances.
We adjust these calls to use run_command_list() instead of run_command().
This change permits these variables to have embedded newlines so that
they work the same as the 'source' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
This new function runs a list of commands separated by semicolon or newline.
We move this out of cmd_source so that it can be used by other code. The
PXE code also uses the new function.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Simon Glass <sjg@chromium.org>
This fix prevents env_import() CRC to fail when CONFIG_ENV_SIZE
is not equal to 4096 bytes
It also prevents mtd->read and mtd->write to be incomplete when
the environment is larger than 4096 bytes.
Signed-off-by: David du Colombier <0intro@gmail.com>
* 'master' of git://git.denx.de/u-boot-i2c:
km/common: remove printfs for i2c deblocking code
CONFIG: SMDK5250: I2C: Enable I2C
I2C: Add support for Multi channel
I2C: Modify the I2C driver for EXYNOS5
I2C: Move struct s3c24x0_i2c to a common place.
EXYNOS: PINMUX: Add pinmux support for I2C
EXYNOS5: define EXYNOS5_I2C_SPACING
EXYNOS: Add I2C base address.
EXYNOS: CLK: Add i2c clock
mx6qsabrelite: add i2c multi-bus support
imx-common: add i2c.c for bus recovery support
i.mx53: add definition for I2C3_BASE_ADDR
i.mx: iomux-v3.c: move to imx-common directory
i.mx: iomux-v3.h: move to imx-common include directory
iomux-v3: remove include of mx6x_pins.h
mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
mxc_i2c: add bus recovery support
mxc_i2c: prep work for multiple busses support
mxc_i2c: add i2c_regs argument to i2c_imx_stop
mxc_i2c: add retries
mxc_i2c: check for arbitration lost
mxc_i2c: change slave addr if conflicts with destination.
mxc_i2c: don't disable controller after every transaction
mxc_i2c: place i2c_reset code inline
mxc_i2c: place imx_start code inline
mxc_i2c: remove redundant read
mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
mxc_i2c.c: code i2c_probe as a 0 length i2c_write
mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
mxc_i2c: create i2c_init_transfer
mxc_i2c: clear i2sr before waiting for bit
mxc_i2c: create tx_byte function
mxc_i2c: remove ifdef of CONFIG_HARD_I2C
mxc_i2c: fix i2c_imx_stop
i2c: deblock i2c bus also if accessed before realocation
Signed-off-by: Wolfgang Denk <wd@denx.de>
If we switch to a different i2c bus in changing the mux config for the
i2c mux, we have to be sure to deblock the bus also before realocation.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The commit 5dd95cf93d 'usb_storage:
Fix EHCI "out of buffer pointers" with CD-ROM' introduce a bug in
usb_storage as it wrongly assumes that every transfer can use
4096 bytes per qt_buffer. This is wrong if the start address of
the data is not page aligned to 4096 bytes and leads to 'EHCI
timed out on TD' messages because of 'out of buffer pointers'
in ehci_td_buffer function.
The bug appears during load of a fragmented file and
read from or write to an unaligned memory address.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Return values of submit_{control,bulk}_msg() functions
should be checked to detect possible error.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
usb_get_descriptor passes it's buffer argument directly to
usb_control_msg() so it has to be properly aligned/padded.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This can be useful for generic scripts. For example, rather than hard-
coding a script to ext2load tegra-harmony.dtb, it could load
${soc}-${board}.dtb and hence not need adjustments to run on multiple
boards.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is needed for the SPEAr SPL support, as SPEAr uses the mkimage
header to wrap and validate the images (SPL & U-Boot).
Signed-off-by: Stefan Roese <sr@denx.de>
This allows MMC drivers to perform cache flusing on the bufffers
without issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a new command "sysboot" which parses syslinux menu files and boots
using kernel and initrd specified by menu files. The operation is similar
to "pxe boot" except local files on ext2 or fat filesystem are parsed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
For syslinux, the initrd can be set in the append string as
"initrd=<file>", so try to find it there if we haven't already set the
initrd.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
If the file path starts with a '/', then don't pre-pend the bootfile path.
This fixes a problem with running 'pxe boot' multiple times where the
bootfile path gets pre-pended to itself each time.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Kernels can be specified using "linux" or "kernel" entry. The difference
is kernel is supposed to detect the type of file, but for u-boot both are
treated the same.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make the menu timeout apply only when prompt flag is set and after the
menu is displayed. This allows auto boot to work no matter whether prompt
is set or cleared. Use the default selection if the menu times out.
This also fixes the timeout value given to readline_into_buffer to be
seconds instead of 10th of seconds.
Old behavior:
if prompt
display menu and wait for choice
else
wait for timeout
if key pressed
display menu and wait for choice
else
exit command
New behavior:
if prompt
display menu
if key pressed
wait for choice
else
boot default entry on timeout
else
boot default entry
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Simplify the code slightly by using a for() loop since this is
basically what we're already doing -- incrementing "ngood" to
the value in "count".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Not only does the source code get simpler, but it also shrinks the
compiled object code too.
While we're here, tweak the summary message to avoid the plural
issue. It isn't that big of a deal, and it's currently wrong
anyways in the single (1 byte) case:
Total of 1 byte were the same
Grammar wise, that should be "was" rather than "were". The new
output people should be able to easily figure out:
Total of 1 byte(s) were the same
Total of 10 byte(s) were the same
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 418396e212 introduced a
bug that causes nand read and nand write to crash in strcmp
due to a null pointer.
Root cause is that strchr(cmd, '.') returns a null pointer when
the input string does not contain a '.'
The strcmp function does not check for null pointers, resulting
in a crash.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Scott Wood <scott@tyr.buserror.net>
Currently bmp_display() is static and can not be used directly
in the driver or board code. Export it for other users.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Before this patch, bootp would not overwrite the value, but the
value was still clobbered in the env
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
cmd_nand.c: In function 'raw_access':
cmd_nand.c:397:9: warning: variable 'rwsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
cmd_bootm.c: In function 'do_bootz':
cmd_bootm.c:1590:9: warning: variable 'iflag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-usb:
USB: S5P: Add ehci support
usb:udc:samsung Add functions for storing private gadget data in UDC driver
usb:gadget:composite: Support for composite at gadget.h
usb:gadget:composite USB composite gadget support
usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
USB: Document the QH and qTD antics in EHCI-HCD
USB: Drop cache flush bloat in EHCI-HCD
USB: Drop ehci_alloc/ehci_free in ehci-hcd
USB: Align buffers at cacheline
usb: use noinline define
* 'master' of git://git.denx.de/u-boot-nand-flash:
NAND: Remove ONFI detection message to from bootup log
driver/mtd:IFC: Fix possible memory leak
driver/mtd: IFC NAND: Add support of ONFI NAND flash
mtd, nand: move some printfs to debug output.
nand_util: correct YAFFS image write function
powerpc/85xx: fix NAND boot linker scripts for -fpic
nand: extend .raw accesses to work on multiple pages
This avoids cache-alignment warnings shown in console
when a usb command is entered.
Whenever X bytes of unaligned buffer is invalidated, arm core
invalidates X + Y bytes as per the cache line size and throws
these warnings.
Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Building usb for Blackfin boards fails as we get linux/compiler.h
included which expands the "noinline" inside of the attribute and
we get attribute(attribute(noinline)).
Explicitly use the helper define to avoid this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A use for this is to read, modify, erase, and write an entire block as a
single unit, as a replacement for the biterr command. This way gives
more flexibility in that you can also test multiple bit errors, errors
in the ECC, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
sata functions are called even if previous functions failed
because return value is not checked.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lin_gadget: use common linux/compat.h
linux/compat.h: rename from linux/mtd/compat.h
lin_gadget: use common mdelay
gunzip: rename z{alloc, free} to gz{alloc, free}
fs/fat: align disk buffers on cache line to enable DMA and cache
part_dos: align disk buffers on cache line to enable DMA and cache
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
cmd_nand.c: In function ‘arg_off_size’:
cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Some Freescale SOCs support 32-bit and 36-bit physical addressing, and
U-Boot must be built to enable one or the other. Add this information
to the bdinfo command.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
If one command fails, 'run' command should terminate and not execute
any remaining variables.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Tested-by: Wolfgang Denk <wd@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The standalone example does not have get_timer() defined, so we cannot
rely on it being available.
Move the timer function into boootstage.c to avoid this problem.
This corrects a build breakage for the standalone example on some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
SPI flash operations inadvertently stretching beyond the flash size will
result in a wraparound. This may be particularly dangerous when burning
u-boot, because the flash contents will be corrupted rendering the board
unusable, without any warning being issued.
So add a consistency checking so not to overflow past the flash size.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
image.c: In function ‘boot_get_ramdisk’:
image.c:800:8: warning: unused variable ‘end’ [-Wunused-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
This patch allows loading RAW ramdisk via bootz command. The raw ramdisk is
loaded only in case it's size is specified:
bootz <kernel addr> <ramdisk addr>:<ramdisk size> <fdt addr>
For example:
bootz 0x42000000 0x43000000:0x12345 0x44000000
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: albert.u.boot@aribaud.net
Cc: afleming@gmail.com
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This command boots Linux zImage from where the zImage is loaded to. Passing
initrd and fdt is supported.
Tested on i.MX28 based DENX M28EVK
Tested on PXA270 based Voipac PXA270.
NOTE: This currently only supports ARM, but other architectures can be easily
added by defining bootz_setup().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: albert.u.boot@aribaud.net
Cc: afleming@gmail.com,
Cc: Simon Glass <sjg@chromium.org>,
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
The following must be defined:
CONFIG_ENV_IS_IN_FAT
Enable this saving environment to FAT.
FAT_ENV_INTERFACE
Interface the FAT resides on (e.g. mmc).
FAT_ENV_DEVICE
The interface device number (e.g. 0 for mmc0)
FAT_ENV_PART
The device part (e.g. 1 for mmc0:1)
FAT_ENV_FILE
The filename of the environment file.
Author: Maximilian Schwerin <mvs@tigris.de>
Removed dead DEBUG comment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
print in the "log info" command, if "log_version = 2" also the
value from "log->v2.con".
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
If the logbuffer contains LOGBUFF_LEN chars, they never got
printed with the "log show" command, because chars get
printed with the following for loop:
for (i = 0; i < (size & LOGBUFF_MASK); i++) {
with size = LOGBUFF_LEN and LOGBUFF_MASK = (LOGBUFF_LEN-1)
for loop never executed ...
Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Fixed merge conflict.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
This adds a spl command to the u-boot.
Related config:
CONFIG_CMD_SPL
activate/deactivate the command
CONFIG_CMD_SPL_NAND_OFS
Offset in NAND to use
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
Without this patch, some versions of gcc (at least ELDK 4.2) complain
about dereferencing type-punned pointers.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Once CONFIG_FAT_WRITE is defined, users can invoke 'fatwrite' command
that saves data in RAM as a FAT file.
This patch was originally part of
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/121847
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Maximilian Schwerin <mvs@tigris.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This reverts commit 295d3942b8.
It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
This inserts bootstage calls into tftp, usb start and bootm. We
could go further, but this is a reasonable start to illustrate
the concept.
Signed-off-by: Simon Glass <sjg@chromium.org>
This defines the basics of a new boot time measurement feature. This allows
logging of very accurate time measurements as the boot proceeds, by using
an available microsecond counter.
To enable the feature, define CONFIG_BOOTSTAGE in your board config file.
Also available is CONFIG_BOOTSTAGE_REPORT which will cause a report to be
printed just before handing off to the OS.
Most IDs are not named at this stage. For that I would first like to
renumber them all.
Timer summary in microseconds:
Mark Elapsed Stage
0 0 reset
205,000 205,000 board_init_f
6,053,000 5,848,000 bootm_start
6,053,000 0 id=1
6,058,000 5,000 id=101
6,058,000 0 id=100
6,061,000 3,000 id=103
6,064,000 3,000 id=104
6,093,000 29,000 id=107
6,093,000 0 id=106
6,093,000 0 id=105
6,093,000 0 id=108
7,089,000 996,000 id=7
7,089,000 0 id=15
7,089,000 0 id=8
7,097,000 8,000 start_kernel
Signed-off-by: Simon Glass <sjg@chromium.org>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch clear and disable the data cache for vxWorks.
The entry point sysInit(int) intended by Windriver to be called from
the vxWorks bootrom, a very small vxWorks system.
The routine is called by the go() handler in the bootrom, that clears
the cache from start of image to end of usable memory.
The PowerPC implementations only invalidates and disable the cache,
the ARM implementations also flush it.
U-Boot will be on the safe side, if it disables the data cache before
calling vxWorks sysInit(int).
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
boot_get_fdt() expects a uImage-wrapped FDT to be loaded to a staging
location, and then memmove()s it to the load address specified in the
header. This change enhances boot_get_fdt() to detect when the image has
already been loaded to the correct address, and skip this memmove(). The
detection algorithm was written to match the equivalent for the kernel;
see bootm_load_os()'s IH_COMP_NONE case.
v2: New patch
Signed-off-by: Stephen Warren <swarren@nvidia.com>
flush_dcache()/flush_icache() aren't defined in common.h,
flush_dcache_all()/invalidate_icache_all() however are.
Let the icache and dcache commands use those instead.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currently have the same code in hush.c and main.c. This brings the
code into one place.
As an added feature, if the command function returns CMD_RET_USAGE then
cmd_process() will print a usage message for the command before
returning the standard failure code of 1.
ARM code size increases about 32 bytes with this clean-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a nasty interleave of #ifdefs in hush.c where the two code
paths have different indents. Remove this ickiness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Boards can select either the 'built-in' parser or the hush parser. We
should not call builtin_run_command() if we are using the hush parser.
We use run_command() instead, since it knows how to call the correct
parser.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The current run_command() is only one of the parsing options - the other
is hush. We should not call run_command() when the hush parser is being
used. So we rename this function to better explain its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
It really isn't clear why this is here and there is no comment, so
drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Following the corresponding Linux code, this patch relaxes reset timings
waiting at least 100ms after power to the ports. There are some reports
that it helps make enumeration work better on some high speed devices.
Furthermore, the wait is only done once after power has been enabled
on all ports.
CC: Remy Bohmer <linux@bohmer.net>
CC: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
This moves keyboard polling logic from USB HCD drivers into USB
keyboard driver. Remove usb_event_poll() as keyboard polling was
the only user of this API. With this patch USB keyboard works with
EHCI controllers again. Tested on a tegra2 seaboard.
Signed-off-by: Allen Martin <amartin@nvidia.com>
When keys are pressed on the numeric keypad, emit key codes for the numbers,
operators, dot and enter.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
When doing a "GET_REPORT" request on the keyboard control endpoint,
the report ID should 0 (ie report ID not used) rather than 1
as reports are not used in boot mode.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
With 2a8e0fc nand_do_read_ops changed in behavior slightly (keeping in sync
with the kernel which did this change in b64d39d8) such that the OOB data is
always copied into oobbuf and never appended to datbuf. Within U-Boot only
the nand_dump function (for the dump nand subcommand) was expecting the OOB
data to only be appended to datbuf. So we now change nand_dump to not
malloc extra space, correct the comment about datbuf and OOB data and switch
the pointer to oobbuf before printing.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The commit message of a28afca (Add uboot "fdt_high" enviroment variable)
states that fdt_high behaves similarly to the existing initrd_high.
But fdt_high actually has an outstanding difference from initrd_high.
The former specifies the start address, while the later specifies the
end address.
As fdt_high and initrd_high will likely be used together, it'd be nice
to have them behave same. The patch changes the behavior of fdt_high
to have it aligned with initrd_high.
The document of fdt_high in README is updated with an example to
demonstrate the usage of this environment variable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
* 'sf' of git://git.denx.de/u-boot-blackfin:
README: Add description of SPI Flash (SF) command configuration
sf command: allow default bus and chip selects
sf: eeprom_m95xxx: set a sane default timeout
sf: eeprom_m95xxx: fix up style
This patch allows a board configuration file to provide default bus
and chip-selects for SPI flash so that first argument to the 'sf' command
is optional.
On boards that use the mxc_spi driver and a GPIO for chip select, this allows
a much simpler command line:
U-Boot> sf probe
instead of
U-Boot> sf probe 0x5300
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
show a menu on startup instead running the shell.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jason Hobbs <jason.hobbs@calxeda.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
add the possibility to show a statusline when printing a menu
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jason Hobbs <jason.hobbs@calxeda.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
add possibility to add a timeout when reading a line
into a buffer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
When performing large bulk reads from a CD or DVD using the U-Boot
usb_storage driver, it generates requests of up to 20 blocks at a time.
With a standard 512-byte block size, that is 10240 bytes and within the
limit of U-Boot's EHCI driver (maximum 5 pages at 4k per page).
Unfortunately CD-ROM media has a 2048-byte blocksize, resulting in a
maximum transfer size of 40960 bytes, which does not fit.
Since the EHCI specification is impossibly obtuse and far beyond my
comprehension, I chose to dynamically compute the limit based on the
blocksize.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
env_get_char_spec() function is duplicated across multiple environment
files.
Remove the duplication by providing a default implementation.
Add "weak" declaration, so the default implementation can be overridden.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* 'next' of ../next:
mkenvimage: Add version info switch (-V)
mkenvimage: Fix getopt() error handling
mkenvimage: Fix some typos
phy: add Micrel KS8721BL phy definition
net: introduce per device index
mvgbe: remove setting of ethaddr within the driver
x86: Add support for specifying an initrd with the zboot command
x86: Refactor the zboot innards so they can be reused with a vboot image
x86: Add infrastructure to extract an e820 table from the coreboot tables
x86: Add support for booting Linux using the 32 bit boot protocol
x86: Clean up the x86 zimage code in preparation to extend it
x86: Import code from coreboot's libpayload to parse the coreboot table
x86: Initial commit for running as a coreboot payload
CHECKPATCH: ./board/esd/hh405/logo_320_240_8bpp.c
CHECKPATCH: ./board/esd/hh405/logo_1024_768_8bpp.c
CHECKPATCH: ./board/esd/hh405/logo_320_240_4bpp.c
CHECKPATCH: ./board/esd/hh405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/apc405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/voh405/logo_320_240_4bpp.c
CHECKPATCH: ./board/esd/voh405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/hh405/fpgadata.c
CHECKPATCH: ./board/esd/pci405/fpgadata.c
CHECKPATCH: ./board/esd/tasreg/fpgadata.c
CHECKPATCH: ./board/esd/apc405/fpgadata.c
CHECKPATCH: ./board/esd/voh405/fpgadata.c
CHECKPATCH: ./board/esd/ash405/fpgadata.c
CHECKPATCH: ./board/esd/dasa_sim/fpgadata.c
CHECKPATCH: ./board/esd/ar405/fpgadata_xl30.c
CHECKPATCH: ./board/esd/ar405/fpgadata.c
CHECKPATCH: ./board/esd/plu405/fpgadata.c
CHECKPATCH: ./board/esd/wuh405/fpgadata.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci405.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci405ab.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci4052.c
CHECKPATCH: ./board/esd/canbt/fpgadata.c
CHECKPATCH: ./board/esd/du405/fpgadata.c
CHECKPATCH: ./board/esd/cpciiser4/fpgadata.c
CHECKPATCH: ./board/dave/PPChameleonEVB/fpgadata.c
avr32:mmu.c: fix printf() length modifier
fat.c: fix printf() length modifier
cmd_sf.c: fix printf() length modifier
Make printf and vprintf safe from buffer overruns
vsprintf: Move function documentation into header file
Add safe vsnprintf and snprintf library functions
Move vsprintf functions into their own header
Conflicts:
tools/mkenvimage.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The switch to strict_strtoul() was not done correctly - this fixes
the compile error when CONFIG_CMD_TFTPPUT is active.
There appears to very little use of strict_strtoul() in commands, so
it might be easier to switch to simple_strtoul(). If not, we should
decide the best way to use strict_strtoul(). For now I have added a
friendly message which will of course increase code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix:
cmd_pxe.c: In function 'parse_pxefile_top':
cmd_pxe.c:941:5: warning: 'err' may be used uninitialized in this
function [-Wuninitialized]
cmd_pxe.c:921:6: note: 'err' was declared here
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jason Hobbs <jason.hobbs@calxeda.com>
Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
do_env_import() missed the final '\0' terminator when calculating the
size of an environment data block. This led to an erroneous 'bad CRC,
import failed' message for a checksum protected environment (-c.)
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
size_t is not always 'unsigned int', use corret length modifer.
This patch fixes following warning:
---8<---
cmd_sf.c: In function 'spi_flash_update_block':
cmd_sf.c:130: warning: format '%#x' expects type 'unsigend int', but argument 4 has type 'size_t'
cmd_sf.c:135: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'size_t'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
cc: Mike Frysinger <vapier@gentoo.org>
cc: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
From: Sonny Rao <sonnyrao@chromium.org>
utilize the added vscnprintf functions to avoid buffer overruns
The implementation is fairly dumb in that it doesn't detect
that the buffer is too small, but at least will not cause crashes.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
In 9792987721 Stefan describes a usecase
where the previous behavior of leaving wMaxPacketSize be unaligned
caused fatal problems. The initial fix for this problem was incomplete
however as it showed another cases of non-aligned access that previously
worked implicitly. This switches to making sure that all access of
wMaxPacketSize are done via (get|put)_unaligned.
In order to maintain a level of readability to the code in some cases
we now use a variable for the value of wMaxPacketSize and in others, a
macro.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
OpenRISC:
Tested-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Beagleboard xM, Pandaboard run-tested, s5p_goni build-tested.
Signed-off-by: Tom Rini <trini@ti.com>
We already flush the kernel image after we've loaded it to ensure
visiblity to the other cores. We need to do the same thing for the
ramdisk and device tree images. In AMP boot scenarios we might not be
HW cache coherent with the secondary core that we are loading and
setting the ramdisk and device tree up for. Thus we need to ensure
we've flushed the regions of memory utilized by ramdisk and device tree
so the loadding and any modifications (from decompression or fdt updates)
are made visible to the secondary cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-usb:
USB: efikamx: Enable USB on EfikaMX and EfikaSB
USB: Add generic ULPI layer and a viewport
USB: EHCI: Allow EHCI post-powerup configuration in board files
USB: mx51evk: add end enable USB host support on port 1
USB: mx53loco: add end enable USB host support on port 1
USB: MX5: Add MX5 usb post-init callback
USB: MX5: Abstract out mx51 USB pixmux configuration
USB: MX5: add generic USB EHCI support for mx51 and mx53
USB: MX5: add helper functions to enable USB clocks
usb:gadget:s5p Enable the USB Gadget framework at GONI
usb:gadget:s5p USB Device Controller (UDC) implementation
ehci: speed up initialization
usb: add help for missing start subcommand
cosmetic: remove excess whitespace from usb command help
usb: align usb_endpoint_descriptor to 16-bit boundary
usbtty: init endpoints prior to startup events
pxa: convert pxa27x_udc to use read and write functions
pxa: activate the first usb host port on pxa27x by default
pxa: fix usb host register mismatch
ehci-fsl: correct size of ehci caplength
USB: Add usb_event_poll() to get keyboards working with EHCI
USB: gadaget: add Marvell controller support
USB: Fix complaints about strict aliasing in OHCI-HCD
USB: Drop dead code from usb_kbd.c
USB: Rework usb_kbd.c
USB: Add functionality to poll the USB keyboard via control EP
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
* Support dynamic allocation of devices
* Passing data via usb device privptr
* Reorder functions to avoid forward declarations
* Introduce generic polling mechanism to fix musb and ehci-hcd breakage
due to using "extern new;" to access keyboard driver data!
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
This allows the keyboard to avoid requests via Interrupt Endpoint altogether and
run all requests via Control Endpoint. This uses the Get_Report request.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Rebased on current code.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Using mmap to allocate memory from the OS for RAM simulation we can use
u-boot own malloc implementation.
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for console output before the console is inited.
The main purpose of this is to deal with a very early panic() which would
otherwise cause a silent hang.
A new board_pre_console_putc() function is added to the board API. If
provided by the board it will be called in the event of console output
before the console is ready. This function should turn on all UARTs and
spray the character out if it possibly can.
The feature is controlled by a new CONFIG_PRE_CONSOLE_PUTC option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
During the rebase of commit 00b7d6e "USB: Squash checkpatch warnings
in usb_kbd.c" I missed a brace, resulting in a number of build errors.
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Rebased to current code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-arm:
davinci: Remove unwanted memsize.c from hawkboard's nand spl build
devkit8000: Move CONFIG_SYS_TEXT_BASE out of bss
da850evm: pass board revision info to kernel
arch/arm/include/asm/arch-omap5/clocks.h: Fix GCC 4.2 warnings
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix GCC 4.6 warnings
arch/arm/cpu/armv7/omap-common/spl.c: Fix GCC 4.2 warnings
MX35: flea3: changes due to hardware revision B
MX: serial_mxc: cleanup removing nasty #ifdef
M28: Fix OB1 bug in GPIO driver
MXS: Add static annotations to dma driver
apbh_dma: return error value on timeout
Efika: Configure additional regulators for HDMI output
mx5: Correct a warning in clock.c
MC13892: Add REGMODE0 bits definitions
mx51evk: Configure the pins as GPIOs prior to using gpio_get_value
mx53smd: Configure the pins as GPIOs prior to using gpio_get_value
mx53evk: Configure the pins as GPIOs prior to using gpio_get_value
mx53ard: Configure the pins as GPIOs prior to using gpio_get_value
mx53loco: Configure the pins as GPIOs prior to using gpio_get_value
OMAP3: Add SPL_BOARD_INIT hook
AM3517 CraneBoard: Add SPL support
AM3517: Add SPL support
OMAP3: Add SPL support to omap3_evm
OMAP3: Add SPL support to Beagleboard
OMAP3 SPL: Add identify_nand_chip function
OMAP3 SPL: Rework memory initalization and devkit8000 support
OMAP3: Suffix all Micron memory timing parts with their speed
OMAP3: Add optimal SDRC autorefresh control values
omap3: mem: Add MCFG helper macro
OMAP3: Remove get_mem_type prototype
OMAP3: Change mem_ok to clear again after reading back
OMAP3: Add a helper function to set timings in SDRC
OMAP3: Update SDRC dram_init to always call make_cs1_contiguous()
omap3: mem: Comment enable_gpmc_cs_config more
ARM: davici_emac: Fix condition for number of phy detects
arm: printf() is not available in some SPL configurations
arm, davinci: add support for am1808 based enbw_cmc board
arm, davinci: move misc function in arch tree
arm, board/davinci/common/misc.c: Codingstyle cleanup
arm, davinci, da850: add uart1 tx rx pinmux config
arm, davinci: move davinci_rtc struct to hardware.h
arm, davinci: Remove duplication of pinmux configuration code
arm, hawkboard: Use the pinmux configurations defined in the arch tree
arm, da850evm: Use the pinmux configurations defined in the arch tree
arm, da850: Add pinmux configurations to the arch tree
arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes
arm, hawkboard: Remove obsolete struct pinmux_config i2c_pins
arm, davinci: Move pinmux functions from board to arch tree
arm, arm926ejs: always do cpu critical inits
omap_gpmc: use SOFTECC in SPL if it's enabled
nand_spl_simple: add support for software ECC
AM3517: move AM3517 specific mux defines to generic header
AM35xx: add EMAC support
davinci_emac: hardcode 100Mbps for AM35xx and RMII
davinci_emac: fix for running with dcache enabled
arm926ejs: add noop implementation for dcache ops
davinci_emac: conditionally compile specific PHY support
davinci_emac: use internal addresses in buffer descriptors
davinci_emac: move arch-independent defines to separate header
BeagleBoard: config: Really switch to ttyO2
ARM: davinci_dm6467Tevm: Fix build breakage
ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
ARM: OMAP3: Remove unused define SDRC_R_C_B
ARM: OMAP3: Remove unused define CONFIG_OMAP3430
omap4: fix IO setting
omap4+: streamline CONFIG_SYS_TEXT_BASE and other SDRAM addresses
omap4460: add ES1.1 identification
omap4: emif: fix error in driver
omap: remove I2C from SPL
omap4460: fix TPS initialization
omap: fix cache line size for omap3/omap4 boards
omap4: ttyO2 instead of ttyS2 in default bootargs
omap: Improve PLL parameter calculation tool
start.S: remove omap3 specific code from start.S
armv7: setup vector
armv7: include armv7/cpu.c in SPL build
armv7: disable L2 cache in cleanup_before_linux()
arm, arm926ejs: Fix clear bss loop for zero length bss
PXA: Move colibri_pxa270 to board/toradex/
PXA: Flip colibri_pxa27x to pxa-common.h
PXA: Introduce common configuration header for PXA
PXA: Rename pxa_dram_init to pxa2xx_dram_init
PXA: Squash extern pxa_dram_init()
PXA: Export cpu_is_ and pxa_dram_init functions
PXA: Cleanup Colibri PXA270
PXA: Replace timer driver
PXA: Add cpuinfo display for PXA2xx
PXA: Separate PXA2xx CPU init
PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
PXA: Unify vpac270 environment size
PXA: Enable command line editing for vpac270
PXA: Adapt Voipac PXA270 to OneNAND SPL
PXA: Drop Voipac PXA270 OneNAND IPL
PXA: Fixup PXA25x boards after start.S update
PXA: Re-add the Dcache locking as RAM for pxa250
PXA: Rework start.S to be closer to other ARMs
PXA: Drop XM250 board
PXA: Drop PLEB2 board
PXA: Drop CRADLE board
PXA: Drop CERF250 board
Fix regression in SMDK6400
nand: Add common functions to linux/mtd/nand.h
Ethernut 5 board support
net: Armada100: Fix compilation warnings
ARM: remove duplicated code for LaCie boards
ARM: add support for LaCie 2Big Network v2
mvsata: fix ide_preinit for missing disks
netspace_v2: Read Ethernet MAC address from EEPROM
omap3evm: Add support for EFI partitions
part_efi: Fix compile errors
It is fine to use __maybe_unused instead of #ifdef, but we also need one
for print_eth() since not all boards have Ethernet. This fixes this
warning:
cmd_bdinfo.c:39:13: warning: 'print_eth' defined but not used [-Wunused-function]
Signed-off-by: Simon Glass <sjg@chromium.org>
Jagannadha Sutradharudu Teki
Tom Rini
Sergey Lapin
Albert ARIBAUD
York Sun
Masahiro Yamada
Harvey Chapman
Doug Anderson
Wolfgang Denk
Ying Zhang
Simon Glass
Bob Liu
SRICHARAN R
Michal Simek
Vivek Gautam
Julius Werner
Michael Heimpold
Andreas Bießmann
Egbert Eich
Benoît Thébaudeau
Stefan Roese
Jaehoon Chung
Maxime Larocque
Che-liang Chiou
Joe Hershberger
Vadim Bendebury
Mingkai Hu
Stephen Warren
Rob Herring
Anatolij Gustschin
Akshay Saraswat
Pali Rohár
Steven Stallion
Andre Renaud
Jeroen Hofstee
Stephen Warren
Lukasz Majewski
Pantelis Antoniou
Barak Wasserstrom
Robert P. J. Day
Nikita Kiryanov
Enric Balletbo i Serra
Otavio Salvador
Daniel Schwierzeck
Sonic Zhang
Stefano Babic
Fabio Estevam
Phil Sutter
Vipin Kumar
Piotr Wilczek
Holger Hans Peter Freyther
Reinhard Arlt
Gabor Juhos
Ilya Yanok
Kim Phillips
Richard Genoud
Jim Lin
Rajeshwari Shinde
Stefan Reinauer
James Miller
Allen Martin
Vincent Palatin
Milind Choudhary
Luigi Semenzato
Tom Wai-Hong Tam
Kenneth Waters
Anton Staaf
Marek Vasut
Taylor Hutt
Gerald Van Baren
Gabe Black
Tom Wai-Hong Tam
Hung-Te Lin
Pavel Herrmann
Eric Nelson
Lucas Stach
Gerlando Falauto
Michal Simek
Lei Wen
Pavel Machek
Chander Kashyap
Igor Grinberg
Iwo Mergler
Thierry Reding
Jagannadha Sutradharudu Teki
Jim Shimer
Shaohui Xie
Liu Gang
Uma Shankar
Jorgen Lundman
Charles Manning
Dirk Eibach
David du Colombier
Holger Brunck
Stefan Herbrechtsmeier
Mike Frysinger
Steve Sakoman
Donghwa Lee
Puneet Saxena
Scott Wood
Timur Tabi
Timo Ketola
Marek Vasut
Maximilian Schwerin
Heiko Schocher
Simon Schwarz
Jason Hobbs
Matt Porter
Donggeun Kim
Stefan Kristiansson
Wolfgang Grandegger
Shawn Guo
Peter Meerwald
Hadli, Manjunath
Kyle Moffett
Horst Kronstorfer
Andreas Bießmann
Sonny Rao
Kumar Gala
Veli-Pekka Peltola
Matthias Weisser