This adds support for the i.MX6 based Eltec HiPerCam board.
This board comes with different i.MX6 flavours and different
memory sizes. Currently supported is the i.MX6dl version with
256MB DDR3 RAM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The BCTs are build objects and as such are located in the objtree instead of
the srctree. Fix out-of-tree build by defining a variable which refers to the
board directories in the objtree and use it for Tegra.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A lot of the image makefiles define an equal board variable, which
gives the impression that this variable is unique for this makefile.
As those files aren't freestanding makefiles but get included into a
parent makefile this is not actually true. Attempts to override this
variable will not work reliable as make is picking up a random instance.
Fix this confusion by moving this variable out of the individual makefiles.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The main idea behind this patch is to avoid redundant board code.
Because of the module similarities of all am335x based phytec boards, we can
merge its code.
The phytec-som-am335x merges the code of all am335x based phytec SOMs.
So we will have only one "board" in the barebox for phyCORE, phyFLEX.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the Altera SoCFPGA Development Kit.
The setup is based on the GHRD from Altera.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
PIE is a form of dynamic linking and thus inherently incompatible
with -static. It worked ok as the current behavior of ld.bfd is
to not respect -static if -pie has been specified.
ld.gold and future versions of ld.bfd will fail to link if both
of those incompatible switches are specified at the same time.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support phyFLEX-i.MX6 SOM with 1GB on one ram bank
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the imx28evk to multiimage support and adds the
lowlevel initialization to make the bootlets unnecessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- Enable multi-image support to generate bootstream, sd-card and 2nd stage
images.
- Handle pin-mux in lowlevel.c only.
- Use fine-tuned memory setup from u-boot.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- enable multiimage support to generate bootstream, sd-card and 2nd
stage images
- Enable new defaultenv support
- Enable more features
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Freescale MXS SoCs have a multi staged boot process which needs
different images composed out of different binaries. The ROM executes
a so called bootstream which contains multiple executables. The first
one is executed in SRAM and the purpose of this binary is to setup
the internal PMIC and the SDRAM. The second image is usually the
bootloader itself. In case of barebox the bootstream is composed
out of the self extracting barebox image (pblx) and the prepare
stage for setting up the SDRAM.
The bootstream image itself is useful for USB boot, but for booting from
SD cards or NAND a BCB header has to be prepended to the image. In case
of SD boot the image has the .mxssd file extension in barebox.
Since the bootstream images are encrypted they are not suitable for
2nd stage execution. For this purpose the 2nd stage images are generated.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Freescale i.MX6sx sabresdb board.
Tested are:
- UART
- The three SD card slots
- USB host
- USB otg (host and device mode)
- FEC (both)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyBOARD-SUBRA which use a phyFLEX-i.MX6 (pfla02) module.
- i.MX6 SOLO with 512MB RAM
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyBOARD-ALCOR which use a phyFLEX-i.MX6 (pfla02) module.
- i.MX6 Quad with 1GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds xz decompression support from the kernel. Both compressing
the barebox binary with xz and decompressing xz files on the commandline
is supported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Boards like phyBOARD-WEGA RDK have an phyCORE-AM335x
connected with no SPI NOR flash. Added dts to support this.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The nitrogen6x have variants with 2GB SDRAM. Add support for them. The
imxcfg files are from U-Boot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Karo TX6X family consists of different i.MX6Q/DL based System-on-Modules.
Add support for the TX6u 801x modules, that have an i.MX6DL SoC.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For now only the Quad 1GB variant is supported.
Tested:
- starting barebox over USB
- writing barebox to NAND with barebox_update
- starting Linux kernel over TFTP
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes various stability issues seen on new boards
with the old setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit adds a new Marvell Kirkwood-based board, by following the currently
supported boards.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for 256MB and 128MB RAM configurations of the
phyCORE-AM335x. This is done as new images.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will add support for Embedsky E9 board.
It is a small board based on i.MX6 Quad with 2G of RAM.
http://en.embedsky.com/product_info.php?cateid=169&id=169
Signed-off-by: Andrey Panov <rockford@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The rule in barebox is to name the directories after
the modules. As hummingboard is just one of the
carriers for the MicroSOM module, name the directory
accordingly.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This converts Marvell Armada XP based PlatHome Openblocks AX3-4
to PBL_MULTI_IMAGES. A DT overlay is added to keep possible
barebox-specific changes separated and added to lowlevel
board init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This converts Marvell Armada XP based Marvell Armada XP GP
to PBL_MULTI_IMAGES. A DT overlay is added to keep possible
barebox-specific changes separated and added to lowlevel
board init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This converts Marvell Armada 370 based Globalscale Mirabox
to PBL_MULTI_IMAGES. A DT overlay is added to keep possible
barebox-specific changes separated and added to lowlevel
board init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Jan Luebbe
Sascha Hauer
Marc Kleine-Budde
Lucas Stach
Wadim Egorov
Steffen Trumtrar
Christian Hemp
Jan Luebbe
Teresa Gámez
Stefan Müller-Klieser
Lucas Stach
Ezequiel Garcia
Andrey Panov
Sebastian Hesselbarth