DISK_DRIVE is missing in Kconfig, so remove the "select" statement.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
EIO is a better error message to describe the data transfer to or from the SD cards has failed.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The host limits are only one limit we must honor when changing the transmission frequency.
The SD cards have their own limits, so take them also into account.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the SD card spec the detection can happen at 400 kHz
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since a generic block reset function is a available, also the MCI driver
should make use of it.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MMC_BUS_WIDTH_* macros do not correspond with the real bus width.
After setting a bus width larger than 1 bit the next call to change the
frequency ends in the default handler and the host interface stays silently
at the previous frequency.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove some leftover from former powerpc support which has no
relevance for i.MX based esdhc controllers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Linux expects linux,initrd-end to contain the first unused address. As
this doesn't match the end semantic used by barebox (i.e. end contains
the last used address) adding one is necessary.
Without this change Linux fails for me to correctly extract a gzipped
cpio archive provided as initrd.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the iomux-v3 (found on i.MX25,35,51,53,6) to pinctrl
support. The old SoC specific API is kept for compatibility. The
pinctrl devicetree support is enabled automatically when OFDEVICE
support is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a massively stripped down pinctrl support. The upper API
consists of only of:
int pinctrl_select_state(struct device_d *dev, const char *state);
This is used to setup the pinmux for a device to a certain state.
This function normally does not need to be called manually. The
device core will setup the default state before probing a device.
The pinctrl core has the job of handling the devicetree. It parses
the pinctrl phandles for a device from devicetree, finds the correct
pinctrl device and calls its set_state callback with the pinctrl
setup device node.
The simplicity of this pinctrl framework comes from the fact that
we:
- Limit usage to devicetree only for now. For non devicetree use the
old legacy SoC specific APIs still can be used.
- Do not parse the devicetree into internal data structures which
are used by the drivers later. This adds the overhead that we
may parse the devicetree multiple times for more dynamic setups,
but on the other hand we do not need to parse devices from the
devicetree we don't use in barebox
- Do not detect resource conflicts. Since the framework mainly is
a devicetree parser this would be hard to implement. It should
be easy for board maintainers to avoid resource conflicts though.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rename "drivers/gpio.c" to "drivers/gpiolib.c".
Reason is for understand functionality of driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
pass a struct cdev instead of the cdev name to of_parse_partitions.
This is available to the caller anyway and makes it easier to use
additional stuff from the cdev (like knowing whether it's a mtd
device).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The phandles have to be parsed completely before registering the devices
from the devicetree. Otherwise drivers can't rely on of_find_node_by_phandle
in their probe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Taken from the Linux kernel, simplified and reworked to match barebox.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
actually ops.ooboffs is not defaulted so when its value gets
added to chip->oob_poi in nand_fill_oob or nand_transfer_oob
the respective memcpy is using a wrong address.
With this patch, both md -s /dev/nandraw0 and cp xyz /dev/nandraw0.sb
are working fine on an i.MX28 target (instead of crashing the board).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
if the flash has a known type, the ONFI detection won't occur
and thus we may not detect the right parameters.
By testing both namd and pagesize, as done in the kernel, we
can detect ONFI flash with know IDs.
As an example on an i.MX53 board :
- without the patch :
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xd3
(Micron NAND 1GiB 3,3V 8-bit), page size: 4096, OOB size: 128
- with the patch :
ONFI flash detected ... ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xd3
(Micron MT29F8G08ABACAWP), page size: 4096, OOB size: 224
in the first case the OOB size is wrong.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 17176c2e2b adds a test of a new RTC
register flag to distinguish a system reset and a wake up event. Shame on me,
I have forgotten to define the newly used flag yet.
While already here, I also try to document the other flags the RTC provides.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_get_phy_mode to parse the phy mode from the devicetree and
of_get_mac_address to parse a MAC address from the devicetree.
Directly taken from the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The core has a bit for swapping packet data endianism.
Reset default from Cadence is off. Xilinx however, that uses this core on the
Zynq SoCs, opted for on. Turn it off for all devices.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The macb/gem core is used by the Zynq SoC. In preparation of sharing
the macb driver between at91 and Zynq, rename the platform data to
'struct macb_platform_data', and move the definition to a common
location.
Signed-off-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 5f03074 changed storing struct resource end insted of size.
Fix calculation of end in fb
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If a key is pressed but not released before booting and the key is
connected to an active low gpio it's not detected. This patch solves
that.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we use a full buffer no need to check the SOF
and reset the rx_tail
fix at the same time the gem detection so we can have the rx_buffer
allocated correctly according to the IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to better detect whether a clk is enabled or not.
- If we can ask a clk, ask it. If it's enabled, go on and ask parents
- If we can't ask it, but it can be enabled, depend on the enable_count.
if it's positive, go on and ask parents
- If we can't ask it and it cannot be enabled, assume it is enabled
and ask parents.
This makes the CLK_ALWAYS_ENABLED unnecessary, since the fixed clk now
always returns 1 in its is_enabled callback.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wait until fifo is empty, not until fifo is not full.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some systems are runnignfrom a very limited SRAM, but have a huge
malloc space in SDRAM. The bss normally is in SRAM, so we should
avoid having big structures there. The gpio_desc table is 3072 bytes
big, so allocate it dynamically instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
struct bus_type contains an embedded struct device_d which is quite
a big structure. Dynamically allocate this instead to save the space
in the binary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fix chipidea-imx usb initialization.
"imx_chipidea_port_init" was moved before PORTSC setup in the
commit "USB i.MX chipidea: implement post init support". This
change breaks usb function with ULPI. Patch moves port initialization
back after PORTSC setup, so it works again.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
by reordering the entry, USB gadget support is now a menu and the
USB gadget choices are under this menu and not directly in the
driver menu.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for system controller register driver (SYSCON).
Code taken from Linux Kernel and adapted for using in barebox.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for CLPS711X GPIOs. Driver based on
generic GPIO driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds generic memory-mapped GPIO controller support.
Code taken from Linux Kernel and adopted for barebox.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds clocksource driver for CLPS711X targets and adds
support to platform to use this new driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With 2k NAND flashes the data layout in memory is not what is
written on the flash device. This leads to the result that the
factory provided bad block markers are not recognized correctly.
To preserve the factory bad block information the i.MX NAND driver
will not scan for the bad blocks itself when there is no flash based
bbt available, because the mtd layer would do so based on wrong
information. Instead, a new command is introduced which allows to
manually create a flash bbt based on the correct information.
As this command is tightly coupled to mtd and the i.MX NAND driver
the command is placed under drivers/mtd/nand/ instead of commands/
where a command normally belongs to.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The information which kind of bbt (if any) is used is hidden somewhere
in the NAND layer. Expose it to a device parameter to make it detectable
and visible during runtime.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have framework support for delayed probing of
ata devices implement it in the ahci driver to actually make use
of it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ata device usually take a long time to spin up, so it makes sense
to only spend this time when the device is actually used.
This adds a logical ata device and attaches a 'probe' parameter
to it, similar to what MMC does.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following commit accidently bailed out if the link is up, not
when it's down as stated in the commit message.
| commit a3f74d928c
| Author: Rob Herring <rob.herring@calxeda.com>
| Date: Mon Feb 11 18:02:00 2013 +0100
|
| ahci: handle COMINIT received during spin-up
|
| Some Intel SSDs can send a COMINIT after the initial COMRESET. This causes
| the link to go down and we need to re-initialize the link.
|
| Signed-off-by: Rob Herring <rob.herring@calxeda.com>
| Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
OFDEVICE decides whether or not we compile in support for probing
devices from the devicetree. Let the user decide this explicitly.
This makes the oftree, of_node and of_property commands independent
of devicetree device support since being able to manipulate
devicetrees has nothing to do with probing devices from the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to be able to handle multiple devicetrees, do not assume
the tree to be unflattened is the barebox internal one. Instead,
just return a pointer to it and assign the barebox internal root_node
external to the unflatten function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The allnodes list makes it hard to handle multiple devicetrees. Having
a list to iterate over all nodes of a tree is still good to have though.
This patch uses the list_head of the root node as the head of the list.
This way the root node is no longer part of the list, but when iterating
over a tree the root node is not interesting anyway.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_find_node_by_path iterates over the allnodes list. Depending on
where the node we look for is, this can be significantly slower than
using the tree structure to look for a node, so iterate over the tree
instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes following warning:
drivers/w1/w1.c: In function 'w1_found':
drivers/w1/w1.c:471: warning: integer constant is too large for 'long' type
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes following warning:
drivers/mtd/nand/nand_write.c: In function 'nand_do_write_ops':
drivers/mtd/nand/nand_write.c:272: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While erasing bad blocks is a potentially dangerous operation
it is sometimes needed during development or when some foreign
code has touched the flash.
This patch adds a device parameter 'erasebad' to allow erasing
bad blocks. Since this is not wanted during production this is
behind a Kconfig option.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have some NAND specific stuff during registration,
like for example adding NAND specific device parameters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since recently we check for the page being written for not being
empty and do not actually write it when it is. This fails for a
freshly created flash bad block table when all blocks are good.
In this case the bbt code will try to write an empty page, but
with the BBT marker in OOB. This page never gets written, so the
BBT code will not find a bad block table during next start up and
writes it again. Fix this by checking if we want to write OOB data,
if we do, then write the page, even if the data is empty.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
do not try to read the status in force mode
the link is up
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not write pages which only contain 0xff. UBI expects pages which
seem empty to be writable. This got lost with:
| commit 3139c3e9a6
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date: Thu Nov 29 11:16:40 2012 +0100
|
| mtd core: call driver write function with complete buffer
|
| mtd->write is supposed to loop around pages internally, no need
| to do this in mtd_write. This fixes a huge write performance drop
| with the m25p80 driver when it was converted to a mtd driver recently.
| Since mtd->writesize is 1 for this driver mtd_write ended up doing
| single byte writes on the flash.
Introduce mtd_all_ff as a global function since UBI currently has its own
implementation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
RTS is an output. Either flow control is used and you care about the state or
it is not used and you don't care. So setting it to active does no harm in
either case. This is inline with what Linux does.
Mandatory for Highbank as example
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch provides rename MFD-related symbols for using MFD-prefix.
Additionally, sorting mfd/Kconfig and mfd/Makefile records.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds USB gadget support to the i.MX chipidea driver. Basically
we have to add a register function to the fsl udc driver and call
this from the chipidea driver if device mode is selected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Alexander Shiyan
Juergen Beisert
Sascha Hauer
Antony Pavlov
Uwe Kleine-König
Lucas Stach
Eric Bénard
Jan Luebbe
Hubert Feurstein
Steffen Trumtrar
Josh Cartwright
Jan Weitzel
Vicente Bergas
Jean-Christophe PLAGNIOL-VILLARD
Marc Kleine-Budde
Rob Herring