hostname_init() must be called after the devicetree root node has been
initialized, otherwise the check on board compatible always returns
false.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With CONFIG_PARTITION_NEED_MTD enabled we use mtd rather than devfs
directly to create partitions on mtd devices. Since:
| commit b32cd8df87
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date: Wed Apr 9 15:49:32 2014 +0200
|
| mtd: nand: bb: use mtd api directly
|
| The devfs layer just adds an addition indirection between mtd
| and the bb devices with no purpose. Drop it.
|
| Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The bad block aware device creation doesn't work if this option
is disabled. With this we remove CONFIG_PARTITION_NEED_MTD and always
use mtd partitions on mtd devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some of the barebox specific changes that were added in commit
e0316b4dd7 got lost during the switch to use
upstream dtsi files in commit bb7cf71cff.
Especially the memory size is important since we have two different memory
sizes which have to be handled.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This isn't much different from the default 1,16V
and I haven't seen this make a difference on any
board, but it seems to be required for some T30 SKUs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It's not safe to ramp up the CPU clock speed to
1,4 GHz on all T30 SKUs, as this may result in failure
to start the kernel properly. Start CPU at 600 MHz,
which is safe even for the slowest SKUs.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This board wasn't changed properly, as it was merged in the short
timeframe where the signature change waited to be applied. Change
it now to get rid of the compiler warning.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For small systems we would put the zImage at 32KiB after
the start of memory, and put the DT a bit after the uImage.
The kernel will always try to relocate itself and overwrite
the DT.
Try to be more clever at uImage placement to avoid
triggering the kernel relocation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For small systems we would put the zImage at 8MiB after
the start of memory, and put the DT a bit after the zImage.
When we encounter an image which is bigger than 8MiB
uncompressed, the kernel would try to relocate itself
and overwrite the DT.
Try to be more clever at zImage placement to avoid
triggering the kernel relocation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If we have two discontinuous memory banks we want to move
the malloc area into the upper bank by default to leave as
much free space in the lower bank, where we have to place
kernel, oftree and initrd.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox now accepts FDTs outside
of it's visible DRAM, as long as it's a valid pointer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox now accepts FDTs outside
of it's visible DRAM, as long as it's a valid pointer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox now accepts FDTs outside
of it's visible DRAM, as long as it's a valid pointer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Mostly to make it clear that boarddata needs to be
something we can dereference.
As this is a pretty invasive change, use the opportunity
to make the signature 64bit safe.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
FUSEs (OTP registers) can be written via /dev/imx-ocotp character device.
For example, writing MAC 12:34:56:78:9A:BC can be performed as
> mw -l -d /dev/imx-ocotp 0x8c 0x00001234
> mw -l -d /dev/imx-ocotp 0x88 0x56789ABC
and reading as
> md -l -s /dev/imx-ocotp 0x88+8
00000088: 56789ABC 00001234
, where 0x88 (0x22*4) and 0x8C (0x23*4) are offsets of MAC OTP registers.
Notice: FUSEs are PROM, so "0" (unprogrammed) bits
can be replaced with "1" (but not vice versa) only once.
Also, for MAC there are convinient parameters:
> ocotp0.permanent_write_enable=1
> ocotp0.mac_addr=12:34:56:78:9A:BC
imx_ocotp 21bc000.ocotp: reloading shadow registers...
imx_ocotp 21bc000.ocotp: reloading shadow registers...
> echo $ocotp0.mac_addr
12:34:56:78:9A:BC
Signed-off-by: Uladzimir Bely <u.bely@sam-solutions.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the imx6-reg.h include to the imx6-mmdc header.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a clk_gate_flags argument to clock gate creation functions
to allow the introduction of new clock gate modifiers.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a basic support for the ARM-based Rockchip SoCs of the
RK3xxx family.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
GENERIC_GPIO is selected automatically by GPIOLIB
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pingrp defines never made it upstream, so roll back the changes
and use the individual pin defines for the Efika sb instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox used to have its own include/dt-bindings with files copied
from the corresponding kernel files. Use upstream dt-bindings directly
instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reduce the devicetree files for one board with different memory sizes the
memory size can be read back from i.MX6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Beniamino Galvani
Sascha Hauer
Michael Olbrich
Silvio Fricke
Lucas Stach
Lucas Stach
Uladzimir Bely
Christian Hemp
Eric Bénard
Alexander Shiyan