These routines can fail, add support for that. Also, put in missing
copyright headers.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When the i.MX28 boots from USB, the ROM code sets this bit. When
after a reset the ROM code detects that this bit is set it will
boot from USB again. This means that if we boot once from USB the
chip will continue to boot from USB until the next power cycle.
To prevent this (and boot from the configured bootsource instead)
clear this bit here. This bit is not documented in the datasheets,
it was figured out the hard way. Whether this is the same on i.MX23
is currently not known.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx23-olinuxino is a board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fadil Berisha <f.koliqi@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If a second bootstream was used, there was a sanity check which was not
only wrong (using erasesize instead of writesize) but also superfluous
(we got the block from an existing cdev, so it must be in the flash
range). Simply remove it to make bcb work as expected.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit 2f6b1f7690 the pull-up and
bitkeeper handling for i.MX23/28 is correct. But now it is important to
distinguish these pin features as their programmed bit values are different.
With this patch the bitkeeper and pull-up enable/disable bits are now handled
separately.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While a set bit enables the pullup (if exists) it disables the bitkeeper (if
exists). Both features are using the same register bit and only one of this
feature is present on a per pin base.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we now can change HCLK and VDDIO, we can now support writing to
OCOTP. Writing is done via a special data register. This is u32, so we
need to fill a temporary buffer when offset or count is not aligned. The
write is also protected by a special device variable.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Will the code more readable, especially since future additions are
planned.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Let's keep the timeout routine in a central place. We will need it more
often when we add write support.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
usbphy initializaion needs to access the power supply and has this
embedded. Refactor to a seperate power.c, since we need other accesses
in the future.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently the watchdog is occupied for system reset. This usage collides with
the dedicated usage of a watchdog. This patch change the behaviour of at least
i.MX23/i.MX28 where the chipset supports a simple and powerful alternative
to reset the whole SoC (including the PMIC).
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We write a proper FCB, but no DBBT since it is unresolved how to keep it
in sync with Linux-based BBTs. Also, we imply searchcount = 4 and stride
= 64 (which is the default) until we can verify via ocotp.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Based on the U-Boot version. Changed to kernel style register layout, added
MX23 support (WIP!), made MMU aware and adapted to barebox.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Based on the U-Boot version. Changed to kernel style register layout, added
MX23 support, made MMU aware and adapted to barebox.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To avoid getting a different divider due to rounding errors when using
set_hclk later, use DIV_ROUND_UP for the returned value.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Compile fixes unknown symbol 'mxs_ocotp_read' for tx28 defconfig. Since
the vendor stores the MAC address in OCOTP, we always want this driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Read-only support for now to get MAC addresses.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
e62edd3 mxs: Fix support for BITKEEPER() macro
added this macro in iomux-imxc.c but the macro is not present
in the i.MX23 case. Adding it in iomux-imx23.h fix both
imx23evk_defconfig and chumbyone_defconfig
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There was no check for BE, so any BITKEEPER(1) iomux configurations
were not being applied.
Signed-off-by: Esben Haabendal <esben.haabendal@prevas.dk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic support for the mx28-evk board. Debug UART, MMC and FEC
have been successfully used.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Wolfram Sang
Jean-Christophe PLAGNIOL-VILLARD
Fadil Berisha
Juergen Beisert
Maxime Ripard
Eric Bénard
Esben Haabendal