to allow to register an array of drivers
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 89dfe2d2af "mdiobus: do not scan
the bus at registration time" dropped the check for struct mii_bus
element phy_mask while scanning through all addresses.
Re-add this check.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Scanning the bus can take some time. If we do not need the ethernet
device, this is unnecessary, so delay the scan until the phy device
iactually is needed.
Andread Pretzsch: Fixup bug in scanning for all devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
fec_init() initializes some bits important for phy access, so do
this before the mdiobus is registered. This fixes mdiobus support
on i.MX28 boards in RMII mode.
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Test if we already found a phy device on an address earlier and return
it if it exists. This makes it possible to call mdiobus_scan multiple
times.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several i.MX boards (all i.MX6 boards) need to do some adjustments
to phy registers. If barebox itself does not use network, networking
won't work in the kernel if the kernel does not have the fixups. Connect
the phy at probe time so that these tweaks are done during probe so that
the kernel works without phy register tweaks. Also this has the effect
that the phy device is present and introspectable without doing fake
network transfers beforehand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If none set use NA (0) as before.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On i.MX we enable all necessary clocks during startup of the clock
controller driver, so we do not need the register hacking in the drivers
anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The _send function should not return the length
of the transmitted packet.
See also
commit 76c4c9e48f
Author: Jan Luebbe <jlu@pengutronix.de>
Date: Fri Sep 28 18:17:44 2012 +0200
davinci_emac: return 0 on successful transmit
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the device id mechanism to the i.MX fec driver and
uses it to determine the fec version. Also adds devicetree
probing support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_update_linkspeed':
/opt/work/barebox/drivers/net/designware.c:234:9: error: 'mac_p' undeclared (first use in this function)
/opt/work/barebox/drivers/net/designware.c:234:9: note: each undeclared identifier is reported only once for each function it appears in
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_ether_open':
/opt/work/barebox/drivers/net/designware.c:254:6: error: too few arguments to function 'phy_device_connect'
/opt/work/barebox/include/linux/phy.h:252:5: note: declared here
/opt/work/barebox/drivers/net/designware.c: At top level:
/opt/work/barebox/drivers/net/designware.c:226:13: warning: 'dwc_update_linkspeed' defined but not used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can check it with the kernel one
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also pass flags using platform_data and remove useless casts from void*.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The _send function should not return the length of the transmitted packet.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
this will ensure the data are set to 0 (list as example)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It starts the switch and provides basic access to the registers.
This driver could also work with some other Micrel switches, possibly
with some small changes.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since 99e72c8bbd on an i.MX51 based board,
I get : "phy0: Link is up - 1000/Full". It seems miidev tries to probe
the PHY to early and gets 0x3ffff which leads to the wrong capabilities
setting.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If pdata is NULL smc911x_probe will crash. Checking the zero initialized
priv->shift results in default configuration if pdata is not set.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the check need to be inverted
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
poll the READY bit in PMT_CTRL. Any other access to the device is
forbidden while this bit isn't set. Try for 100ms
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use linux kernel chip detection from 3.5
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
detect if the bus is swapped and report a 32bit drivers is used on a 16bit bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
switch ipe337: to it at the same time to do not brake it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to replace them depending on the platform data.
So we can specify shift and reg io witdh (16bit/32bit)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this make the driver more readable
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
miidev_wait_aneg() polled the wrong bit, so link detection did fail on
boards where the PHY had to come out of a powerdown mode.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This update adds the GIANFAR driver along with the configuration
and build files.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The dump generated by "md -w -s /dev/phy0"
suggests individual registers need to be
addressed by byte offset, not by register number.
E.g. to set the autonegotiation advertisement register
for 10Mbit only, use "mw -w -d /dev/phy0 8+2 0x0061".
The current mix of offset == register number, but
count == byte count is unintuitive.
Also, to be consistent with "md" on /dev/mem, round up
the count so "8+1" also works to access one register.
However, no attempt is made to do read-modify-write
single byte writes.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Check if the PHY is really accessible (e.g. the
PHY address is correct) during probe.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The auto negotiation result is the intersect
of the advertised abilities and the link partner abilities.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Straight forward port of Synopsys Designware ethernet
driver from u-boot v2012.04.01.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If DEBUG is defined it fails due to wrong variable names
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some phys need board specific fixups. To be able to do this
from board code add mii_open/mii_close functions so that the
board can use the regular mii_read/mii_write functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently only 100Mb/s is tested. Freescale's U-Boot suggests that
there are some additional adjustments necessary for Gigabit support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wait until the reset bit is actually cleared instead of some
arbitrary delay (which caused problems with a PHY which was in some
energy saving mode).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
First check the status at least once, then do timeout checks. Minor
cleanups also.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for KS8851 16bit MLL chip from Micrel Inc.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will ensure that we send an other packet only when the first one is send.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
First call mii_unregister which is done in the drivers unbind function,
then eth_unregister. Also, remove unregister_device which is done in
eth_unregister.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, we can only print the phy_status. Factor out the routine to
get the status, so we can query it from fec drivers and configure
accordingly. Needed because mx28 needs a special bit set for 10Mbit.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Q: "the linux driver add these bits, why not we?"
A: Because nobody activated the bits?
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Introduce a variable which gets updated when needed and only written
once. Will make further additions easier.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
remove double include, remove unused (and double in case of RCNTRL)
defines, sort the includes at least somewhat.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for the old DM9000E device is now part of the new dm9k.c driver. So,
remove the old driver source and switch all users to the new driver.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for the more recent DM9000A and DM9000B types, and keeps
support for the older DM9000E device. As this patch is more or less a complete
re-wrote of the existing driver I add a new source file instead of fixing the
existing one. In a later patch the old driver will be removed.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We never had interrupt support in barebox and we have no plans to
add interrupt support. Even if we do I doubt the current fragments
of irq support are helpful, so remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jean-Christophe PLAGNIOL-VILLARD
Andreas Pretzsch
Sascha Hauer
Antony Pavlov
Jan Luebbe
Eric Bénard
Jan Weitzel
Wolfram Sang
Renaud Barbier
Johannes Stezenbach
Juergen Beisert
Hubert Feurstein