this device controller is present on rm9200/9260/9g20/9261/9g10/9263
the 9g45 use an other IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support the setup of the mmc voltage, when booting OMAP4 with twl6030
from nand.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added i2c support for omap4. Tested on pcm049.
Driver based on linux kernel implementation.
Also added a shift to access 16-bit registers
to make support for OMAP730/850 possible.
If accessing a non existing slave the bus will go into arbitration mode.
It's unable to recover from it.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a function to remap an IO range into a virtual addresses
range. This is particulary usefull for the few devices
mapped at physical address 0, as the MTD boot devices.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The icache command is unused. Instead of adding it to compilation
again, remove it as the cpuinfo command provides the same information.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
configure BP4 and BP3
use BP4 to start DFU mode at boot
if BP4 is pressed at boot time and maintain at least 5s the dfu is started
otherwise we boot normaly
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
by default boot from nand with the bootstrap as first stage
update the smc config for 9g20-ek
switch to defaultenv
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have a bootm command which boots everything we can
simplify the defaultenvironment. We can call bootm on every
image type and can remove the kernelimage_type variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the bootm code to the new uimage code. Also
bootm can now handle other types of images than uImages.
Currently the only architecture making use of this is
arm which allows to boot zImages, raw images and barebox
images.
I intended to make a more bisectable series from this but
I failed becuase there are many dependencies and no matter
how I tried the patches grew bigger and and bigger. So I
decided to put this all in a single patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
whoever calls this function is not necessarily aware of a struct
image_data, so remove the dependency from the function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for the old DM9000E device is now part of the new dm9k.c driver. So,
remove the old driver source and switch all users to the new driver.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on at91sam9 you need to shutdown the sdram/ddr controler before reseting
when you boot from nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Newer pcm038 are populated with a PC28F256P30BFE NOR-Flash.
This flash requires different CS values.
The values also work with older NOR-Flashes.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add all available video modes to the framebuffer. devinfo fb0
shows the available modes. We can select a mode now.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
a temporary setting was inserted in the default env by error
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this, the pins seems to be opendrain and thus the LCD signals
are not properly driven leading to wrong colors on the screen.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add the platform data for MMC/SD card host on the PXA SoCs.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add mmc clock frequency reader. Easy as MMC host controller
is constant, while the clock between host and card is
settable.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt mainline kernel pxa27x_udc driver to barebox :
- remove function header comments as they are in mainline
- test it with serial gadget
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The core support was brought by Marc and Sascha.
The cache choice was fixed by Luotao Fu.
Some gpio and devices addons were provided by Robert.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Barebox cannot boot the recent mainline Linux kernels for the
i.MX21ADS board anymore when using TFTP, because the heap is too
small.
This is solved by increasing the heapsize to 5Mbyte.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All handlers used to just relocate the image without any checks, so
we are doomed if we write outside of SDRAM or will overwrite ourselves.
Move the relocation up to the generic part where we have a chance
of catching these issues.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that the arch_number and system_rev variables can be set from
the environment we don't need the old bootm command line switch
mechanism anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch_number is currently exported to the environment but not read back
on boot time which is rather confusing. system_rev and system_serial
are not exported to the environment but can be set in board specific
code.
This patch exports all these variables to the environment and reads them
back on boot time. All variables get a armlinux_ prefix, so the
arch_number environment variable gets renamed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We never had interrupt support in barebox and we have no plans to
add interrupt support. Even if we do I doubt the current fragments
of irq support are helpful, so remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rename create_section into create_sections, as the function
is used to create multiple sections, and in particular it
creates the 4096 sections of 1MBytes to have a 1:1 flat
mapping of the 4GBytes address space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These symbols where defined for the A9M2440 platform. Rename them to the
platform they now belong to.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
nand.c issues a warning when imx_nand_set_layout is
empty. We don't need this function on i.MX53, so
silence the warning.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The S3C2440 CPU comes with an internal OHCI the generic part of
Barebox already supports. Just add the missing part.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, there are multiple definitions of run_shell()
for each board that can be build in "xload" configuration.
Now there is only one function used by all boards.
The functions defined in xload.c are used only when "xload"
configuration used; but it gets compiled unconditionally.
This has been fixed as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If the user has parsed a tree, we start Linux using the
device tree, otherwise we use the traditional ATAG
mechanism.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When building sandbox with ccache, one would hit warnings such as:
warning: 'struct mmsghdr' declared inside parameter list
on random files; a way to reproduce this issue is to build a simple
file doing just:
#include <sys/socket.h>
int main(void) {
return 0;
}
gcc -Wall -P -c -o foo foo.c
But actually the -P flag is only useful when generating non-C files,
such as linker scripts in the case of barebox. Removing the -P flag
from all the gcc invocations, except when generating .lds files makes
the warning go away. It turns out that this is what
linux/scripts/Makefile.build also does nowadays.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Running the 'bootz' command always fails with
could not read <some file>
due to wrong usage of pointers and structures. This is the second try to fix
the 'bootz' command. At least on my target it is now be able again to load a
kernel without any error.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Running the 'bootz' command always fails with
could not read <some file>
due to it loads only a size of a pointer, instead of the size of the expected
header structure.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Contrary to other Atmel boards, the AT91SAM9M10G45EK board file only
describes the case where NAND is used as the storage for Barebox and
its environment. Therefore, it makes sense to enable the Atmel NAND
driver in the default configuration for this board.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The environment partition was overlapping the Barebox partition in
those three Atmel boards. Saving the environment resulted in the
Barebox being overwritten.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We switched to resources recently and the nand controller
of the i.MX53 needs two of them, so fix the helper in the
same way as the i.MX51
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds lowlevel (AIPS, PLL, L2) initialization for i.MX53 boards.
This is a direct transcription of Freescales U-Boot assembler code
with the exception that we initialize PLL1 with 1000MHz and assume
that all necessary voltages are already adjusted when we arrive here.
It must be explicitely called from the boards so a board is free to
do it's own initialization. However, boards should use this code
and make it more configurable if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes alignment for the "System Type" menu entry.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested on imx53 loco board with a Multi uImage file
generate like this
mkimage -A arm -O linux -T multi -C none -a 0x70008000 -e 0x70008000 -n Linux-2.6.35.3-00745-gce4c61a-dirty -d zImage:rootfs.cpio.lzma uImage.Multi
and boot via bootm
bootm -r @1 -L 0x72000000 /dev/ram0.kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following compile errors
arch/arm/mach-at91/at91sam9g45.c:185:3: error: 'ohci_clk' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9g45.c:186:3: error: 'tcb1_clk' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9g45_devices.c: In function 'at91_add_device_mci':
arch/arm/mach-at91/at91sam9g45_devices.c:258:2: warning: implicit declaration of function 'at91_clock_associate'
[...]
arch/arm/mach-at91/built-in.o: In function `at91_add_device_mci':
sam9_smc.c:(.text.at91_add_device_mci+0x1d0): undefined reference to `at91_clock_associate'
arch/arm/mach-at91/at91sam9260_devices.c: In function 'at91_add_device_mci':
arch/arm/mach-at91/at91sam9260_devices.c:251:2: warning: implicit declaration of function 'at91_clock_associate'
which were introduced in commit:
"at91: swtich to clkdev" (ae19fe26cc)
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This brings consistency to the way variables are named and used
according to the Freescale documentation. Also, since user is
supplying row indicies, and not offsets, it's reasonable to amend the
error message accordingly.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds additional Kconfig help to clarify the way to use barebox
for eFuses handling.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
By doing this we can remove the ptes field in struct arm_memory
which won't be present in a generic memory bank structure anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The nand controller on i.MX51/53 uses two base addresses. Instead
of hardcode the second address use the new shiny resources two specify
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on the Linux driver. Tested with m25p80 with CS in GPIO mode.
Clock setting support is ad-hoc as the corresponding mach is not using
the generic clock infrastructure.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes the following compile errors
arch/arm/mach-at91/at91sam9g45.c:185:3: error: 'ohci_clk' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9g45.c:186:3: error: 'tcb1_clk' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9g45_devices.c: In function 'at91_add_device_mci':
arch/arm/mach-at91/at91sam9g45_devices.c:258:2: warning: implicit declaration of function 'at91_clock_associate'
[...]
arch/arm/mach-at91/built-in.o: In function `at91_add_device_mci':
sam9_smc.c:(.text.at91_add_device_mci+0x1d0): undefined reference to `at91_clock_associate'
arch/arm/mach-at91/at91sam9260_devices.c: In function 'at91_add_device_mci':
arch/arm/mach-at91/at91sam9260_devices.c:251:2: warning: implicit declaration of function 'at91_clock_associate'
which were introduced in commit:
"at91: swtich to clkdev" (ae19fe26cc)
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
from linux
commit 8251544f9e28058e54c4f35b7cd13b0d191d7555
Author: Ryan Mallon <ryan@bluewatersys.com>
The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can dynamise the boot depending on the machine
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit c71a77ab8 (ns16550: switch to resource) has introduced generic
read/write access to 16550 register and a 'shift' parameter to allign
register index to physicall registers.
The correct 'shift' value was missing in all omap based boards.
Corrected this to 2 which has fixed the problem.
Tested on a PCM-049 phyCORE-OMAP4 board.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Tested-by: Jan Weitzel <J.Weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This helper function can be used for automatic
SDDR configuration based on register settings
made by a previously first stage bootloader
i.e. x-loader.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 7d25a0552dd3a4b65412ae1cbf8f9ca8a88b5d27
Author: Juergen Beisert <jbe@pengutronix.de>
Date: Thu Nov 25 17:49:11 2010 +0100
Keep frequency multiplier enabled to be able to do a warmstart
The wachtdog's reset does only reset the ARM core, not the whole silicon.
But the PLLs seems to do some strange things: It seems they switch back to
the low frequency reference when the watchdog barks. But in the case the
frequency multiplier is off (not used due to 26 MHz reference usage) the
machine stops, because the PLLs are stopping due to the lack of a reference
frequency. As the power on reset will set the FPM_EN bit again, a power cycle
brings the machine back to life.
By keeping the frequency multiplier enabled, also a warmstart triggered by the
watchdog can restart the machine now.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the datasheet, PUE is not effective without PKE set.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Set new CS0 values for new NOR-Flashes (28F256P33BF).
These values also work with older flashes (28F256P33B).
Also removed unnecessary setup of CSO in the core_init call.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Updated mx53 ddr3 script in order to align with the latest Freescale version from July 8, 2011:
-change ESDREF[REF_SEL]=01 (for 32KHz), from incorrect setting of 00 (64KHz)
-change DDR3 MR0 write to "setmem /32 0x63fd901c = 0x052080b0" from "0x092080b0".
This changes write recovery from 8 clocks to 6 clocks(in line with ESDCFG1[tWR])
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
