The FSF address has changed; The FSF site says that
address is
Free Software Foundation
51 Franklin Street, Fifth Floor
Boston, MA 02110-1301
USA
(see http://www.fsf.org/about/contact/)
Instead of updating it each time the address changes,
just drop it completely treewide.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* some output sections started with "foo: bar", some with "foo = bar". Unify this.
* there was a fixed size to the "foo =" parameters, which wasn't fitting, this
was especially visible at "devinfo global"
* don't output "resources:", "driver:" and "bus:" lines if there are none
resources, drivers or busses involved.
* remove some empty lines
* harmonize differentiation between headlines (e.g. "resources:") and values
by indenting values slightly
* uppercase some texts
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The error messages would dereference the just checked NULL
ptr. As those messages don't add much value without further
info just remove them.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
'ret' is only initialized when info->fbops->fb_activate_var exists, so
only use it in this case.
Reported-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have dev_add_param_enum() now, so use it for the mode_name
setting. Also drop the special case for single mode framebuffers,
just add the mode_name parameter for this case aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
And use it inside struct fb_info. This struct has the advantage
that the supported modes can be passed around in a single pointer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox does not need the screen size directly, but we pass the
framebuffer to Linux via simnplefb it is desirable to pass the
full size of the framebuffer. Default to calculated values from
the screen resolution.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The IPU has a fractional pixelclock divider. When used, this produces
clock jitter which especially LVDS transceivers can't handle. Allow
to disable it via platform_data.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When requested 32bit formats the IPU generated a 24bit format instead.
Implement real 32bit format (xxrrggbb) and let the IPU generate a 24bit format
when requested.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
No need to hardcode the channel parameters for the rgb offsets,
we can calculate them from the fb_bitfields. ipu_ch_param_write_field()
is the same as is the mainline IPUv3 driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
bitfields are not portable and one should make assumptions of the
layout of bitfields. Replace them with the ipu_ch_param_write_field()
which is already used in the mainline IPUv3 driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With the IPU the way the display is connected is completely independent
of the framebuffer pixel format. So instead of specifying a pixel width
in platform_data we have to specify how the display is connected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support to configure the active framebuffer for the kernel through
device tree.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use the mailbox driver to set up a framebuffer based on the firmware
configuration.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for framebuffers with noncontiguous horizontal lines.
Video drivers can set this value if the hardware requires it.
In case a driver does not set it, the current value of
xres * (bpp / 8) is used instead.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the check is wrong as when the clock rate is correctly set
the function will return 0.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXS specific devices have some common infrastructure in the kernel
known as STMP devices. We have the same in barebox, but with a
mxs_ prefix instead of a stmp_ prefix. As some STMP devices are
also found on i.MX6 move the common infrastructure out of MXS
specific files and use the stmp_ prefix.
This is done in preparation for i.MX6 NAND support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds omap display controller support. Currently only
OMAP4 DSS is supported.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 5f03074 changed storing struct resource end insted of size.
Fix calculation of end in fb
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>