as the sam9260ek may not be the first one in the list
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we will add the ihd before
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the lowlevel init is the same as the usb-a9263 except that can not have the
128MiB option
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can add easly the console_none support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
warning: the ohci work only without MMU
enable:
- ehci
- usb strorage
- usb net asix
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
warning: the ohci work only without MMU
enable:
- ehci
- usb strorage
- usb net asix
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Hi Sascha,
I've made the changes you suggested in this resent patch.
Everything related to custom ATAGs has been moved to the board
directory.
The generic code does not make any references to feature lists or
bootloader versions.
About the setup_feature_list prototype:
it has been renamed to atag_appender
it's not a function, it's a pointer to a function. Can it have a
prototype other than it's own declaration?
All non-related changes has been dropped. They were checkpatch.pl
warnings unrelated to this patch.
Regards,
Vicente.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MC34708 depend on I2C or SPI, so let driver depend on SPI too
and rename config option name to MFD_MC34708.
Signed-off-by: Wjatscheslaw Stoljarski <wjatscheslaw.stoljarski@kiwigrid.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This EEPROM is found on the expansion boards available for the 10036
module. Since we won't need to do anything fancy except reading/writing
from it, use bitbanging to communicate with it.
This EEPROM will hold mostly the board_id so that we can determine if
there is an expansion board plugged in and what expansion board it is.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Garz+Fricke Vincell board. This has
a i.MX53 Processor with 512MB of DDR3 RAM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as the support atmel mci drivers does not work on rm9200 and we have the
possibility to use it as spi use it
Originally on rm9200 when the interface mci is in SPI mode we use a DataFlash Card
so allow it but if no dataflash card option is enable use as mmc spi.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on the 9g20 low power version we have a mmc spi as microSD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on the 9g20 low power version we have a mmc spi as microSD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on all the cpu module we have a at25 except on the cogent where we have a at45
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Switch to new environment and add the bootscripts needed for mmc. Also,
update defconfig for new environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds generic board support (CLEP7212, Linux ARM ID=91)
for CLPS711X-target.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Took the mx28evk defconfig, activated DMA and NAND, used savedefconfig;
this patch is the result.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
now we can flash barebox by itself as the bootstrap need to use pmecc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
so be can add more format support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx23-olinuxino is a board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fadil Berisha <f.koliqi@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we are smaller than the 256KiB reserved for barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we are smaller than the 256KiB reserved for barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Tiny6410 and its base board is a pure development platform.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A look into "arch/arm/boards/" offers various boards starting with the
vendor's name in their directory name (like 'eukrea' and 'freescale').
This patch does the same for the currently existing FriendlyARM board
Mini2440.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
This configuration can be used to use barebox as
x-loader replacement.
Also the ECC-Mode is changed from SOFT to BCH8.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for ConnectCore® i.MX51 board from Digi International.
A separate option includes support for debugging board for this module.
Some code taken from the bootloader U-Boot and patch from Digi.
Functional of Ethernet not tested yet.
barebox 2012.05.0-00316-g4024d9c-dirty #0 Wed Jun 6 13:08:25 MSK 2012
Board: ConnectCore i.MX51
Module Variant: i.MX515@600MHz, PHY, Acceleromter (0x0b)
Module HW Rev : 02
Module Serial : B111156789
mc13xxx-spi@mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: Bad block at 0x00ce0000
nand_read_bbt: Bad block at 0x05bc0000
nand_read_bbt: Bad block at 0x0bc40000
ehci@ehci0: USB EHCI 1.00
detected i.MX51 rev 3.0
imx-esdhc@mci0: registered as mci0
imx-esdhc@mci1: registered as mci1
Malloc space: 0x95f00000 -> 0x97efffff (size 32 MB)
Stack space : 0x95ef8000 -> 0x95f00000 (size 32 kB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
Hit any key to stop autoboot: 3
barebox@ConnectCore i.MX51:/
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several boards are getting bigger than their specified maximum binary
size of 256Kb. Enable the TLSF allocator for them which is smaller
than the original dlmalloc. The changed defconfigs are:
eukrea_cpuimx25_defconfig
eukrea_cpuimx35_defconfig
eukrea_cpuimx51_defconfig
usb_a9260_defconfig
usb_a9263_128mib_defconfig
usb_a9263_defconfig
usb_a9g20_128mib_defconfig
usb_a9g20_defconfig
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
with:
- led
- USB Device
- uart
- net
- mmc
- MMU
dfu support
detect it at boot time
if the user button is pressed 5s and the vbus is 1 start the dfu
otherwise the vbus is 1 start usb serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jean-Christophe PLAGNIOL-VILLARD
Vicente Bergas
Sascha Hauer
Wjatscheslaw Stoljarski (Slawa)
Teresa Gámez
Jan Luebbe
Maxime Ripard
Alexander Shiyan
Wolfram Sang
Carlo Caione
Fadil Berisha
Juergen Beisert
Alexey Galakhov
Juergen Kilb
Antony Pavlov