This commit creates MDIO bus devices to separate the MDIO bus
abstraction from the Ethernet device initialisation.
It also updates the configuration of the P2020RDB ports.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ENABLE_DEVICE_NOISE is used only in two network drivers and is
otherwise unused. ENABLE_FLASH_NOISE is completely unused.
ENABLE_PARTITION_NOISE enables DEBUG in the partition command,
but this code has no debug messages at all.
Remove all this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver should work with some Atheros WiSoCs:
- ar2312, ar2313
- ar2315, ar2316 ...
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX53 fec claims to be compatible to i.MX25 and i.MX53. In barebox
we do not have to make differences between i.MX25 and i.MX27 though, so
just fall back to i.MX27.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The core has a bit for swapping packet data endianism.
Reset default from Cadence is off. Xilinx however, that uses this core on the
Zynq SoCs, opted for on. Turn it off for all devices.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The macb/gem core is used by the Zynq SoC. In preparation of sharing
the macb driver between at91 and Zynq, rename the platform data to
'struct macb_platform_data', and move the definition to a common
location.
Signed-off-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we use a full buffer no need to check the SOF
and reset the rx_tail
fix at the same time the gem detection so we can have the rx_buffer
allocated correctly according to the IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
do not try to read the status in force mode
the link is up
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Due to a hw bug do not enable teh Asym_Pause.
Otherwise if you ser the bit 11 in 4h you will have to unplug
and replug the cable to make the phy work.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
based on the kernel code
detect it via IP version
In the GEM we can use a full packet buffer for receive but the buffer size
need to be 64bit size aligned.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the mininal tx ring size is 2 as if one we wrap on the same descriptor
and can cause IP lock on GEM (gigabit version) this is always the case
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as eth_device init is planning for remove and we need the init before register
the mdio bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Renaud Barbier
Oleksij Rempel
Steffen Trumtrar
Josh Cartwright
Jean-Christophe PLAGNIOL-VILLARD
Alexander Shiyan
Hubert Feurstein
Alexander Aring