Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most devices relevant for barebox like sd/emmc/network/uarts
work. Devicetree contains several undefined drive strength settings,
these can be fixed once the kernel has sorted this out.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding minimal support for the UDOO board.
For more information about the board: http://www.udoo.org/
Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This renames the Freescale and Phytec board directories and defconfig
files to a common naming scheme. The board directories are named
<vendor>-<board> and the defconfig files are named
<vendor>-<board>_defconfig. Also the DataModul realq7 is renamed to its
Marketing Name eDM-QMX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The start-r QSB has a different pmic than the older start QSB.
Add a new dts for the QSRB and let barebox generate two images when
LOCO is selected.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Solidrun has renamed the Carrier-1 to Hummingboard.
This is also the name that is used in upstream Linux,
change barebox to be in line with that.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Only the 1GB variant is supported for now, as I don't
have anything other to test with.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for new board variants. Now Supported are:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d/q modules with 1GiB/2GiB Nanya RAM
- i.MX6s modules with 512MiB/1GiB Nanya RAM
This has been tested on:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d module with 2GiB Nanya RAM
- i.MX6s module with 1GiB Nanya RAM
The possible RAM equipment is:
- For the 512MiB module: 2x Nanya nt5cb128m16fp-di
- For the 1GiB modules: 2x Nanya nt5cc256m16cp or 4x Micron MT41K128M16JT-125
- For the 2GiB module: 4x Nanya nt5cc256m16cp
The 512MiB Nanya board is assumed to work with the same DCD table
as the 1GiB Nanya board. The variant is detected by mirroring at
512MiB, but this hasn't been tested by Pengutronix.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image will be named after the official name of this board:
barebox-freescale-mx6-sabreline.img
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imximage-y is only needed to add its content to $targets so that
the build system does not rebuild the files because of the files
not being in $targets.
Automatically generate the files and add them to $targets and remove
imximage-y
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Phytec phyFLEX-i.MX6 board. The phyFLEX-i.MX6
is a system-on-module based on the Freescale i.MX6 SoC. This patch supports
the 1GiB and 2GiB variants on a PBA-B-01 baseboard.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the GK802 'QUAD CORE Mini PC', which seems to be loosely
based on the Freescale i.MX6Q HDMI dongle reference design.
It is supposedly identical to the Hiapad Hi802.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This reverts commit 08c0e206b3.
The external NAND boot code currently uses the _text linker variable
to determine a place for the image. This doesn't work with multi image
support which will link the binary at 0x0. Revert multi image support
for the pcm038 for now until a solution is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is necessary because the C name for the flash header matches
the filename. For multiple board support we have to make the name
unique to prevent linker errors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is necessary because the C name for the flash header matches
the filename. For multiple board support we have to make the name
unique to prevent linker errors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This converts the Freescale i.MX53 loco aka qsb board to
multi image. The image will be named:
barebox-freescale-imx53-loco.img
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This also converts the Phytec phyCORE i.MX27 aka pcm038 to use
image compression. The image will be named
barebox-phytec-phycore-imx27.img
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Christian Hemp
Eric Bénard
Raphaël POGGI
Lucas Stach
Steffen Trumtrar
Lucas Stach
Rostislav Lisovy
Philipp Zabel
Philipp Zabel