Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pingrp defines never made it upstream, so roll back the changes
and use the individual pin defines for the Efika sb instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox used to have its own include/dt-bindings with files copied
from the corresponding kernel files. Use upstream dt-bindings directly
instead.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise reading or writing to the SPI flash doesn't
work.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The virt2real microcontroller, or virturilka,
is a miniature board for creation of WiFi
or internet controllable smart devices.
See http://virt2real.com for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To ease DT import from Linux, which is still maintained in-tree, we
separate barebox-specific changes by including the original dts in
a separate DT file. This allows to overlay modifications and keep
clean DT history. Additionally, this patch updates i.MX27 DTS tree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link ok
imx-sata 10000000.sata: port 0: Spinning up device...
imx-sata 10000000.sata: port 0: ok.
ata0: registered /dev/ata0
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- declare the rigth mux for the GPIO used to enable the USB's 5V
- enable USB host controller
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Using index 0 for the new disk
Bus 002 Device 003: ID 0951:1654 DT R500
Bus 002 Device 002: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I accidently merged the initial data device node which contained
clocks in the sata node which were not compatible to the ones
in the kernel. Fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When booting from SD Card we don't want to load an env
from EMMC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most devices relevant for barebox like sd/emmc/network/uarts
work. Devicetree contains several undefined drive strength settings,
these can be fixed once the kernel has sorted this out.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding minimal support for the UDOO board.
For more information about the board: http://www.udoo.org/
Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For computer modules the naming standard is to have
a single board directory named after the module and
have all the baseboard support beneath it.
Also change the CONFIG name, as we may want to build
all the baseboards at once.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ ata0.probe=1
imx-sata 10000000.sata: port 0: SATA link ok
imx-sata 10000000.sata: port 0: Spinning up device...
imx-sata 10000000.sata: port 0: ok.
ata0: registered /dev/ata0
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Using index 0 for the new disk
Bus 001 Device 002: ID 0951:1654 DT R500
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Bus 002 Device 003: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- declare the rigth mux for the GPIO used to enable the USB's 5V
- enable USB host controller
tested on i.MX53 START-R :
barebox@Freescale i.MX53 Quick Start-R Board:/ usb -f
USB: scanning bus for devices...
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
Using index 0 for the new disk
Bus 002 Device 003: ID 0951:1654 DT R500
Bus 002 Device 002: ID 0000:0000 EHCI Host Controller
3 USB Device(s) found
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This re-syncs Marvell Dove and Solidrun CuBox DT files with current
files from Linux v3.14. Since barebox specific properties are now
kept separated, we don't need to tweak them anymore.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To ease DT import from Linux, which is still maintained in-tree, we
separate barebox-specific changes by including the original dts in
a separate DT file. This allows to overlay modifications and keep
clean DT history.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- add chosen node with
- environment
- linux,stdout-path
- add dsr value to eMMC
- add provide-mac-address property to iim node
- set memory size in memory node to 0 since we have two different
memory sizes which have to be handled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The start-r QSB has a different pmic than the older start QSB.
Add a new dts for the QSRB and let barebox generate two images when
LOCO is selected.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are two versions of the i.MX53 LOCO:
- the MCIMX53-START board
- the MCIMX53-START-R board
The MCIMX53-START-R has a mc34708 pmic and is otherwise the similar to the
MCIMX53-START. To prepare for the START-R, move all common nodes to a new
imx53-qsb-common.dtsi
and remove everything but the board name and pmic from the imx53-qsb.dts.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Solidrun has renamed the Carrier-1 to Hummingboard.
This is also the name that is used in upstream Linux,
change barebox to be in line with that.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Only the 1GB variant is supported for now, as I don't
have anything other to test with.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Needed to be able to update other i.MX 6 DTs properly.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for new board variants. Now Supported are:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d/q modules with 1GiB/2GiB Nanya RAM
- i.MX6s modules with 512MiB/1GiB Nanya RAM
This has been tested on:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d module with 2GiB Nanya RAM
- i.MX6s module with 1GiB Nanya RAM
The possible RAM equipment is:
- For the 512MiB module: 2x Nanya nt5cb128m16fp-di
- For the 1GiB modules: 2x Nanya nt5cc256m16cp or 4x Micron MT41K128M16JT-125
- For the 2GiB module: 4x Nanya nt5cc256m16cp
The 512MiB Nanya board is assumed to work with the same DCD table
as the 1GiB Nanya board. The variant is detected by mirroring at
512MiB, but this hasn't been tested by Pengutronix.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>