so when the first stage booloader of firmware provide the dtb
we can use it to probe the memory
also allow to print what we probe
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Due to a hw bug do not enable teh Asym_Pause.
Otherwise if you ser the bit 11 in 4h you will have to unplug
and replug the cable to make the phy work.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
based on the kernel code
detect it via IP version
In the GEM we can use a full packet buffer for receive but the buffer size
need to be 64bit size aligned.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the mininal tx ring size is 2 as if one we wrap on the same descriptor
and can cause IP lock on GEM (gigabit version) this is always the case
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as eth_device init is planning for remove and we need the init before register
the mdio bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Previously, during a multi-page write, chip->oob_poi would not be
reinitialized.
See commit f722013ee9fd24623df31dec9a91a6d02c3e2f2f in the kernel
for an analogous change.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we will add later the GMAC IP verion support (GEM)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some 1-wire device need to be search twice to be detected
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This IP is present on the at91sam9 until the sam9g45, on the sam9x5 we use a
new IP.
This driver is based on the linux one.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently there is no common way for the mci host driver to tell
that thee car is write protected. This adds a card_write_protected callback
which is used by the framework to tell whether it's protected or not.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as it's handle by detecting the IP version and bus with
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we need to reset the IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
disable interrupt and reset the IP at the probe
set timout at the host init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
