It wasn't hard to find the right spot to copy the image
to before, but this makes it a bit more explicit.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The voltage for programming the fuses is external to the SoC and
on some boards this is controllable with a regulator, so add regulator
support to the iim driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Allow to read/write the registered MAC addresses in the iim
module directly via a device parameter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX5 iim has an additional bit in the CCM module which
enables the supply. Add support for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx_iim_read is a iim internal function, so access the
internal functions rather than using the cdev API.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With devicetree devicenames start with numbers. Parameters on these
devices are not accessible since variables can't start with numbers.
Register a logical 'iim' device which makes the permanent_write_enable
and explicit_sense_enable parameters accessible again.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of duplicating data shared between the banks in a bank
specific struct, use a iim struct and a bank struct.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is no need to check the card-detect status
for non-removable devices.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Bit 7 of UCR3 is described in the i.MX reference manuals (with the exception
of i.MX1) as follows:
ADNIMP: Autobaud Detection Not Improved-. Disables new features of
autobaud detection (See Baud Rate Automatic Detection
Protocol, for more details).
0 Autobaud detection new features selected
1 Keep old autobaud detection mechanism
The "new features" mechanism occasionally causes the receiver to get out of sync
and continuously produces received characters of '0xff'.
In order to reproduce the problem:
$ cs0.baudrate=19200
- Change the terminal baudrate to 19200
- Type in the console and it should look good
- Change the terminal baudrate back to 115200
- Type 'b' in the console, then a stream of '0xff' is transmitted in loop
Setting the ADNIMP bit avoids the transmission of '0xff' in loop.
Also rename the bit definition as per the reference manual.
Tested on mx6q.
Based on a patch from Eric Nelson for U-boot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch reduces the indentation of "devinfo", to reduce the amount of
overly long lines.
And while we're at it, also remove the fixed-size of the human-readable
area. As entries didn't align anyway (because of indentation), this was
just eating more space without giving much more readability.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* fix indentation of options in 'help bootm'
* add missing help for -m
* put some output into debug/verbose mode
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
"ifconfig" and "ip" from normal Linux userspace shows ethernet addresses
normally in lowercase. And the %pM format specifier in Linux does that,
too. Conform to this custom formatting.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enumeration values will only be shown if there are at least two of them.
With only one enumeration, it was just repeating what was previously printed
anyway.
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* some output sections started with "foo: bar", some with "foo = bar". Unify this.
* there was a fixed size to the "foo =" parameters, which wasn't fitting, this
was especially visible at "devinfo global"
* don't output "resources:", "driver:" and "bus:" lines if there are none
resources, drivers or busses involved.
* remove some empty lines
* harmonize differentiation between headlines (e.g. "resources:") and values
by indenting values slightly
* uppercase some texts
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The command 'devinfo' was first spitting out all devices, and then
also all drivers. This patch separates them into two commands,
'devinfo' as before, and also the new command 'drvinfo'
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As stated in section 29.19.32 of SAMA5D3 Series datasheet, to move
from CS(n) to CS(n+1) the stride is 0x14 and not 0x10 as in the
other AT91 CPUs
Signed-off-by: Matteo Fortini <matteo.fortini@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The MB 77.07 is a small (80x80 mm) single-board computer
developed in Russia by the RC Module.
It was developed as an educational board for К1879ХБ1Я SoC
capabilities demonstration.
See http://www.module.ru/en/catalog/micro/micro_pc/ for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit adds minimal support for the UEMD SoCs
from RC Module (http://www.module.ru).
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Lucas Stach
Lucas Stach
Bo Shen
Fabio Estevam
Holger Schurig
Matteo Fortini
Antony Pavlov