This adds support for the i.MX6 based Eltec HiPerCam board.
This board comes with different i.MX6 flavours and different
memory sizes. Currently supported is the i.MX6dl version with
256MB DDR3 RAM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A lot of the image makefiles define an equal board variable, which
gives the impression that this variable is unique for this makefile.
As those files aren't freestanding makefiles but get included into a
parent makefile this is not actually true. Attempts to override this
variable will not work reliable as make is picking up a random instance.
Fix this confusion by moving this variable out of the individual makefiles.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support phyFLEX-i.MX6 SOM with 1GB on one ram bank
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Freescale i.MX6sx sabresdb board.
Tested are:
- UART
- The three SD card slots
- USB host
- USB otg (host and device mode)
- FEC (both)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyBOARD-SUBRA which use a phyFLEX-i.MX6 (pfla02) module.
- i.MX6 SOLO with 512MB RAM
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyBOARD-ALCOR which use a phyFLEX-i.MX6 (pfla02) module.
- i.MX6 Quad with 1GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The nitrogen6x have variants with 2GB SDRAM. Add support for them. The
imxcfg files are from U-Boot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Karo TX6X family consists of different i.MX6Q/DL based System-on-Modules.
Add support for the TX6u 801x modules, that have an i.MX6DL SoC.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For now only the Quad 1GB variant is supported.
Tested:
- starting barebox over USB
- writing barebox to NAND with barebox_update
- starting Linux kernel over TFTP
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes various stability issues seen on new boards
with the old setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will add support for Embedsky E9 board.
It is a small board based on i.MX6 Quad with 2G of RAM.
http://en.embedsky.com/product_info.php?cateid=169&id=169
Signed-off-by: Andrey Panov <rockford@yandex.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The rule in barebox is to name the directories after
the modules. As hummingboard is just one of the
carriers for the MicroSOM module, name the directory
accordingly.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most devices relevant for barebox like sd/emmc/network/uarts
work. Devicetree contains several undefined drive strength settings,
these can be fixed once the kernel has sorted this out.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding minimal support for the UDOO board.
For more information about the board: http://www.udoo.org/
Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This renames the Freescale and Phytec board directories and defconfig
files to a common naming scheme. The board directories are named
<vendor>-<board> and the defconfig files are named
<vendor>-<board>_defconfig. Also the DataModul realq7 is renamed to its
Marketing Name eDM-QMX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The start-r QSB has a different pmic than the older start QSB.
Add a new dts for the QSRB and let barebox generate two images when
LOCO is selected.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Solidrun has renamed the Carrier-1 to Hummingboard.
This is also the name that is used in upstream Linux,
change barebox to be in line with that.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Only the 1GB variant is supported for now, as I don't
have anything other to test with.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for new board variants. Now Supported are:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d/q modules with 1GiB/2GiB Nanya RAM
- i.MX6s modules with 512MiB/1GiB Nanya RAM
This has been tested on:
- i.MX6q module with 1GiB Micron RAM
- i.MX6d module with 2GiB Nanya RAM
- i.MX6s module with 1GiB Nanya RAM
The possible RAM equipment is:
- For the 512MiB module: 2x Nanya nt5cb128m16fp-di
- For the 1GiB modules: 2x Nanya nt5cc256m16cp or 4x Micron MT41K128M16JT-125
- For the 2GiB module: 4x Nanya nt5cc256m16cp
The 512MiB Nanya board is assumed to work with the same DCD table
as the 1GiB Nanya board. The variant is detected by mirroring at
512MiB, but this hasn't been tested by Pengutronix.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image will be named after the official name of this board:
barebox-freescale-mx6-sabreline.img
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imximage-y is only needed to add its content to $targets so that
the build system does not rebuild the files because of the files
not being in $targets.
Automatically generate the files and add them to $targets and remove
imximage-y
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Phytec phyFLEX-i.MX6 board. The phyFLEX-i.MX6
is a system-on-module based on the Freescale i.MX6 SoC. This patch supports
the 1GiB and 2GiB variants on a PBA-B-01 baseboard.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for the GK802 'QUAD CORE Mini PC', which seems to be loosely
based on the Freescale i.MX6Q HDMI dongle reference design.
It is supposedly identical to the Hiapad Hi802.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This reverts commit 08c0e206b3.
The external NAND boot code currently uses the _text linker variable
to determine a place for the image. This doesn't work with multi image
support which will link the binary at 0x0. Revert multi image support
for the pcm038 for now until a solution is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is necessary because the C name for the flash header matches
the filename. For multiple board support we have to make the name
unique to prevent linker errors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is necessary because the C name for the flash header matches
the filename. For multiple board support we have to make the name
unique to prevent linker errors.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Lucas Stach
Christian Hemp
Steffen Trumtrar
Lucas Stach
Andrey Panov
Eric Bénard
Raphaël POGGI
Rostislav Lisovy
Philipp Zabel
Philipp Zabel