With commit c2ef47887 mci.f_max default value is
only set when pdata is available.
Fix this with always setting the mci.f_max default
value and overrite it when pdata available.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can specify the devname in the board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
At least i.MX53 has errata ENGcm12360:
Occurs when a pending command which issues busy is completed.
For a command with R1b response, the proper software sequence
is to poll the DLA for R1b commands to determine busy
state completion. The DLA polling is not working properly for
the ESDHC module. This is relevant for all eSDHC ports (eSDHC1-4 ports)
DLA bit in PRSSTAT register cannot be
polled to wait for busy state completion.
Updated block guide to reflect that DLA is not applicable to detect
busy state, instead, should poll bit 24 in PRSSTAT register (DLSL[0] bit)
to check that wait busy state is over.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver is already capable of 8 bit buswidth support, so advertise
it to actually make use of it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the SD Host Controller Specification Version 3.00, the ADMA error
status bit is on the wrong bit. Fix this.
While at it, add the missing standard error status bits.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXS specific devices have some common infrastructure in the kernel
known as STMP devices. We have the same in barebox, but with a
mxs_ prefix instead of a stmp_ prefix. As some STMP devices are
also found on i.MX6 move the common infrastructure out of MXS
specific files and use the stmp_ prefix.
This is done in preparation for i.MX6 NAND support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MMC/SD cards normally have a DOS/GPT partition table, but sometimes
barebox uses the unpartitioned area to store its environment. Add
devicetree partition parsing also for SD/MMC cards so that we have
a way to describe the partition in the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The tran_speed field as decoded from csd is valid in most cases,
so use it to determine the maximum clock we can support. It is
not valid though for MMC highspeed cards, in this case the
csd contains invalid values and we have to set tran_speed explicitly
to the maximum speed. As the values passed into mci_set_clock are
now based on tran_speed we no longer have to limit the rate to
tran_speed in mci_set_clock.
The (intended) effect of this patch is that highspeed MMC cards are
no longer limited to non highspeed rates.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In devinfo for the card also print:
- capabilities for host and card
- current bus width
- current clock
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use MMC_CAP_ names instead of MMC_MODE_. This makes it more
clear that these are capabilities of host/card and do not refer
to the current mode. These are in line with the Linux Kernel
except for MMC_CAP_MMC_HIGHSPEED_52MHZ which could be fixed
later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We already have the possibility to register a mci with a certain
filename to get persistent names. However, the device needed to
find the probe parameter still has the name 'mcix'. This patch
changes this by registering the mci device with the same name
as the filename.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some MMC cards support boot partitions. These are special regions
on the MMC card intended to put a bootloader on.
This patch adds support for these partitions, they are accessible
as /dev/diskx.boot[0|1].
Additionally the partitions can be configured bootable using a
device parameter. This can be used to mark the user area or one
of the boot partitions as bootable.
Since this feature is mostly seen on eMMC cards it is made optional
to lower the size impact for boards which do not have eMMC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This updates the i.MX esdhc divider settings to FSLs U-Boot.
Current timings work fine for SD cards, but not for eMMC.
Although the calculation is fine according to the datasheet and reading from
eMMC works, writing is broken. Atleast on i.MX53/tqma53.
With this patch the result is the same, but uses different divider values to
achieve it.
While at it, replace the udelay with a busy-loop.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This gives the SDHCI specific registers a common name and moves
them to a separate file for use by other SDHCI like drivers.
The SDHCI spec has some 16bit and 8bit registers. The i.MX accesses
these as 32bit registers. These register defines now are named after
the SDHCI registers they combine into one, for example:
SDHCI_HOST_CONTROL__POWER_CONTROL__BLOCK_GAP_CONTROL
is the 32bit version of the SDHCI registers HOST_CONTROL, POWER_CONTROL
and BLOCK_GAP_CONTROL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Using the MXS MCI driver with an eight bit capable eMMC results into the
'devinfo' message the interface uses '0' bits for data transfer:
barebox:/ devinfo mxs_mci0
resources:
num : 0
start : 0x80034000
size : 0x00002000
driver: mxs_mci
bus: platform
Interface
Min. bus clock: 1476 Hz
Max. bus clock: 48000000 Hz
Current bus clock: 24000000 Hz
Bus width: 0 bit
The eight bit interface width is stored internally as value '2'. And a two bit
'2' ends up into 0xfffffffe when used as an array index. Using an unsigned
field instead fixes this issue:
barebox:/ devinfo mxs_mci0
resources:
num : 0
start : 0x80034000
size : 0x00002000
driver: mxs_mci
bus: platform
Interface
Min. bus clock: 1476 Hz
Max. bus clock: 48000000 Hz
Current bus clock: 24000000 Hz
Bus width: 8 bit
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
EIO is a better error message to describe the data transfer to or from the SD cards has failed.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The host limits are only one limit we must honor when changing the transmission frequency.
The SD cards have their own limits, so take them also into account.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to the SD card spec the detection can happen at 400 kHz
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since a generic block reset function is a available, also the MCI driver
should make use of it.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MMC_BUS_WIDTH_* macros do not correspond with the real bus width.
After setting a bus width larger than 1 bit the next call to change the
frequency ends in the default handler and the host interface stays silently
at the previous frequency.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove some leftover from former powerpc support which has no
relevance for i.MX based esdhc controllers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch provides rename MFD-related symbols for using MFD-prefix.
Additionally, sorting mfd/Kconfig and mfd/Makefile records.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch moves the register defines and bit definitions
into one include file. As the defines are common for ssp
and mci devices they can be shared.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently there is no common way for the mci host driver to tell
that thee car is write protected. This adds a card_write_protected callback
which is used by the framework to tell whether it's protected or not.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as it's handle by detecting the IP version and bus with
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we need to reset the IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
disable interrupt and reset the IP at the probe
set timout at the host init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to be consistent and have a unique naming convention
be in sync with the kernel too
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to be consistent with the kernel
This also reduce the ligne length
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to be consistent with the kernel
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently there is no common way for the mci host driver to tell
that there is no card present. This adds a card_present callback
which is used by the framework to tell whether it's present or not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Always add the 'probe' parameter to cards so that scripts can
rely on the parameter to be present.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This makes the behaviour more friendly to scripts which can now
set the probe parameter without checking if it has been done before.
Having a succesful result now means that there is a card.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Only the OMAP4 has a register offset of 0x100 in the register space. Fix
this by using the device id mechanism. This became broken when the device
register convenience functions were introduced.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Created ARCH for AM33xx boards as second stage bootloader.
This includes:
- Added dmtimer0
- Created basic header files
- Added MMC support for ARCH_AM33XX
- Added reset function
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Some header file cleanup by:
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The hsmmc module has a 0x100 offset in its register space. The real
register space size for the module is 4K, so when we register the
device with the size 4k, we have to account for the offset in the
driver, not in the resource allocation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When multiple MMC/SD cards are present in the system we often
have to have persistent names to identify them during runtime.
This patch allows to overwrite the devicename which is used.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dev_add_child is a very unsafe function. If called multiple times
it allows setting the same device to different parents thus corrupting
the siblings list. This happens regularly since:
| commit c2e568d19c
| Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| Date: Sat Nov 3 16:11:05 2012 +0100
|
| bus: add bus device
|
| automatically add it as parent of any bus device if none already specified
|
| we have now a nice output per bus
If for example a FATfs is mounted this nice output per bus often ends with:
> `---- fat0
> `---- 0
> `---- 0x86f0000087020031-0x86f000410df27124: /dev/<NULL>
> `---- sram00
> `---- 0x00000000-0xffffffffffffffff: /dev/<NULL>
> `---- 0x00000000-0xffffffffffffffff: /dev/<NULL>
> unable to handle NULL pointer dereference at address 0x0000000c
> pc : [<87f08a20>] lr : [<87f08a04>]
> sp : 86eff8c0 ip : 87f3fbde fp : ffffffff
> r10: ffffffff r9 : 00000000 r8 : 00000003
> r7 : 86f075b8 r6 : 00000002 r5 : ffffffec r4 : 86f07544
> r3 : 00000000 r2 : 43f900b4 r1 : 00000020 r0 : 00000005
> Flags: Nzcv IRQs off FIQs off Mode SVC_32
> [<87f08a20>] (do_devinfo_subtree+0x90/0x130) from [<87f08a90>] (do_devinfo_subtree+0x100/0x130)
>
> [<87f3e070>] (unwind_backtrace+0x0/0x90) from [<87f28514>] (panic+0x28/0x3c)
> [<87f28514>] (panic+0x28/0x3c) from [<87f3e4b8>] (do_exception+0x10/0x14)
> [<87f3e4b8>] (do_exception+0x10/0x14) from [<87f3e544>] (do_data_abort+0x2c/0x38)
> [<87f3e544>] (do_data_abort+0x2c/0x38) from [<87f3e268>] (data_abort+0x48/0x60)
This patch fixes this by adding a device to its parents children list in
register_device so that dev_add_child is no longer needed. This function
is removed from the tree. Now callers of register_device have to clearly
set the parent *before* registering a device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Jan Lübbe <jlu@pengutronix.de>
This patch provides a global cleanup barebox Kconfig files. This includes
replacing spaces to tabs, formatting in accordance format, removing
extraneous lines and spaces. No functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
