The s3c driver passes around a struct device_d * internally in which
it is never interested in. Instead pass around a struct s3c_mci_host
and get rid of all this ugly void * derefs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Yes, it does make sense. First there will always be the next
hardware which has multiple controllers. Also, we shouldn't
give bad examples to others.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As we'll need more arguments to set_ios over time put them
in a struct mci_ios like the kernel does.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Whether a card is high capacity is checked in
sd_send_op_cond/mmc_send_op_cond. Remove the wrong check in
mmc_change_freq which wrongly recognizes some eMMC flash
as high capacity.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
in commit commit f60f6c58e
atmel_mci: check for device id we use to address the right slot
the driver use the dev_id to detect the slot which is wrong on 9263 as we have
2 devices with 2 slots
use slot_b paramter to specify the slot as done in linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are major differences in the clock tree of the S3C24xx family and the
more recent CPUs of the S3C family. Keep the S3C24XX clock routines separate to
avoid an ifdef hell. But also use generic function names to be able to
share drivers among the S3C family.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Start with renaming files to share them in the S3C CPU family,
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The clock rate was incorrectly calculated, leading to a
frequency of 19.5MHz / 64 instead of 19.5Mz for the host
controller.
with the fix applied, a copy of a file of 230 kB shrinks
from 6000ms to 123ms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support the setup of the mmc voltage, when booting OMAP4 with twl6030
from nand.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Increase pxa reading performance by reading 4 bytes at a
time instead of 4 reads of 1 byte.
As the mci controller FIFO accepts reads on bytes, halfwords
or words, use words whenether possible.
The boost is for a 250KBytes file read and display (bmp):
- before: 6900ms
- after: 6000ms
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The write data timeout is too small for old cards,
especially the Transcend 256MBytes SD card. Increase it from
10ms to 100ms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a simple PIO based host controller for MMC and SD cards
on PXA SoCs. Reads and writes are available, and no usage is
made of DMA or IRQs.
SPI mode is not supported yet.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have to check which sd card slot we use. The registered mmc_id is the
the correct parameter for this.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as example today if the timeout happened we can not probe the SD card again
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without CRC support the mmc spi driver fails to compile with
the following:
drivers/mci/mci_spi.c:74:18: error: static declaration of 'crc7' follows non-static declaration
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
'ATA' means more an interface than a disk drive. Change the names to reflect
their real meaning.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds MMC over SPI support to mci-core.c and
mci_spi.c driver.
This driver is useful when SOC doesn't have built-in MCI
component. Tested with nios, 2Go SD-CARD and FAT file system.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to loop around the sectors in mci_sd_write/mci_sd_read.
Now that we have multi block read and write this is not necessary
anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit 4c542622 used the wrong variable name and caused a build failure.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In the Kernel this bug is described like this:
> The CMDTYPE of the CMD register (offset 0xE) should be set to
> "11" when the STOP CMD12 is issued on imx53 to abort one
> open ended multi-blk IO. Otherwise the TC INT wouldn't
> be generated.
> In exact block transfer, the controller doesn't complete the
> operations automatically as required at the end of the
> transfer and remains on hold if the abort command is not sent.
> As a result, the TC flag is not asserted and SW received timeout
> exeception. Bit1 of Vendor Spec registor is used to fix it.
We do not use exact block transfers in barebox, so we only need
the first part of this fix.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When the bus_width was set to 8, then only one data-line has been initialized.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.
based on the original U-Boot patch from
Stefano Babic <sbabic@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It will be called by set_ios anyway later. Also, do not
alter host->clock field, this is none of our business.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows for more type safety. passing a struct device_d
internally in the driver is not a good idea. Also, this
patch adds a void __iomem *regs to mxs_mci_host. dev->map_base
should not be used for register accesses.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is no need to fill the FIFOs before starting a transfer, so
remove corresponding code which is commented out anyway. Additionally
this fixes a compiler warning with gcc4.5
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jürgen Beisert <jbe@pengutronix.de>
We never supported the sigmatel stm chips and probably
never will. So do the first step and rename the architecture
to mxs just like in the kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The idea is to panic() when there is no memory available for normal
operation. Exception: code which can consume arbitrary amount of RAM
(example: files allocated in ramfs) must report error instead of panic().
This patch also fixes code which didn't check for NULL from malloc() etc.
Usage: malloc(), memalign() return NULL when out of RAM.
xmalloc(), xmemalign() always return non-NULL or panic().
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX23 currently uses kHz as the unit for its clock handling and calculation
to avoid overflows when calculation with the internal 480 MHz PLL and its
fractional divider. This patch changes all routines to accept Hz and deliver
Hz as the clock unit.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Silence this warning:
drivers/mci/mci-core.c:1324: Warning: argument `pdata' of command @param is not found in the argument list of mci_register(struct mci_host *host)
drivers/mci/mci-core.c:1324: Warning: The following parameters of mci_register(struct mci_host *host) are not documented:
parameter host
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some mci controllers cannot transfer data with their DMA engines
if the data is not sufficiently aligned. Normally this is a driver
problem, but hey, we have no problem aligning the data and keep
the burden from the drivers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Juergen Beisert <jbe@pengutronix.de>
Acked-by: Juergen Beisert <jbe@pengurtronix.de>
So far only for reading blocks. This is based on the corresponding
U-Boot code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Juergen Beisert <jbe@pengutronix.de>
Acked-by: Juergen Beisert <jbe@pengurtronix.de>
The i.MX23 v2 architecture patch series was sligthly modified to easify
the i.MX28 architecture addition later on. So, we need now an index to
query the SSP clock frequency.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Due to a wrong rounding while calculating the clock divider the requested clock
of 25 MHz resulted into a 48 MHz clock. With this patch a clock frequency
below or equal the requested one will be set.
By using 'div' and 'rate' as vars, its also easier to check against the data
sheet.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This card is working since 'mci: handle SD cards < 2.0 correctly'
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Jürgen Beisert <jbe@pengutronix.de>
Most SD controllers need some kind of alignment for writing
blocks. Instead of coding this in every driver, align write
blocks to a 4 byte alignment in the mci layer. For DMA
accesses we may need bigger alignment, but let's solve this
problem when we have it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With SD cards older than 2.0 the sd_send_if_cond() fails. Do
not assume it's an MMC card in this case. Instead, assume
it's a MMC card if sd_send_op_cond() fails.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a driver for the esdhc controller found on Freescale
i.MX25/35/51 SoCs.
This code is based on the U-Boot driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding MCI card support for S3C2440 CPUs. This is for reference only, as there
is currently no user in the barebox tree. Maybe one with access to the A9M2440
development kit can check it on his/her system.
Checked here with my own S3C2440 based system which is not in the barebox tree.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding MCI card support for STM378x/i.MX23 CPUs. This is for reference only,
as this architecture is currently not part of barebox (but will coming soon).
Its tested on the i.MX23 based ChumbyOne.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the basic framework to handle MCI cards in barebox.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
