Mostly to make it clear that boarddata needs to be
something we can dereference.
As this is a pretty invasive change, use the opportunity
to make the signature 64bit safe.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Phytec phyCARD-i.MX6.
- 1GB RAM on two banks
- 1GB RAM on one bank
- 2GB RAM on two banks
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this board is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- I2C 1/2/3
- 2 LEDs
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a mtd device can have bad blocks we want to create a
bb device, so do this automatically. This allows us to
drop bb device creation from the environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The purpose of envfs_register_partition is to print an error
message when the partition does not exist. Print an error message
from generic code instead and drop this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Not needed anymore, as barebox sets this up itself now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fno-jump-tables isn't enough to guard against
gcc switch optimizations that are unsafe to use
in code that runs before relocation.
The switch-tree-conversion opt pass may generate
lookup tables that are placed in the data section
and accessed via absolute adressing, which fails
prior to relocation.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This most likely doesn't fix any real bugs, but it's the
right thing to do and reduces the noise level with static
checkers.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current implementation fakes a memory-mapped I/O device
at 0x3f8 and 0x2f8, then uses platform read/write functions
to do the actual reading and writing. These platform functions
only exist for the x86 platform; better to move the I/O
routines into the driver and have the driver request I/O ports
using request_ioport_region.
Signed-off-by: Michel Stam <michel@reverze.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For a version 1.0 board the rest of loco_late_init should be executed
to completely configure the board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The board code does a phy reset. This implicitly requests the phy reset
gpio. This gpio is also registered in the devicetree as phy reset gpio,
so the fec driver probe can't request the gpio and bails out with -EBUSY.
Fix this by freeing the phy reset gpio in the board code. While at it use
gpio_request_array for the gpios.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
TX_CLK line is approx. 54mm longer than other TX lines which adds
a delay of 0.36ns. RGMII need a delay of min. 1.0ns. This mean we have to add
a delay of 0.64ns. We choose 0.78 to have a little gap. This can be done by
setting GTX pad skew value to 11100
Also add a delay for the RX delay lines, needed for the Duallite variant.
=> Set register 2.8 (RGMII Clock Pad Skew) to 0x039F.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Otherwise it won't get set in a multiimage build.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The virt2real microcontroller, or virturilka,
is a miniature board for creation of WiFi
or internet controllable smart devices.
See http://virt2real.com for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The commit
ARM: Make ENTRY_FUNCTION more robust
changed the behaviour of the ENTRY_FUNCTION. For the Socrates the call to
__barebox_arm_head() was not removed. Do so now otherwise the Socrates will
not be able to boot barebox.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mx31moboard is used on the marXbot, Eyebot and Footbot robot.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When booting from SD Card we don't want to load an env
from EMMC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a squashed commit of the following downstream
commits:
- Set CS0_END in MMDC0_MDASP to 32Gb (4GB)T
- Fix writes to MMDC0_MDSCR
- Enable bank interleaving (BI_ON) and set write
additional latency (WALAT) to 1 cycle in MMDC0_MDMISC
- Set ARCR_DYN_JMP=1 and ARCR_DYN_MAX=15 in MMDC0_MAARCR
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This was broken with commit 2a1f5f802e
"ARM: rename boards to more consistent naming"
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most devices relevant for barebox like sd/emmc/network/uarts
work. Devicetree contains several undefined drive strength settings,
these can be fixed once the kernel has sorted this out.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adding minimal support for the UDOO board.
For more information about the board: http://www.udoo.org/
Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For computer modules the naming standard is to have
a single board directory named after the module and
have all the baseboard support beneath it.
Also change the CONFIG name, as we may want to build
all the baseboards at once.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- configure the MC34708 properly so that USB can work
(the sequence is taken from u-boot)
- add the required defines to the mc13xxx include file
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To ease DT import from Linux, which is still maintained in-tree, we
separate barebox-specific changes by including the original dts in
a separate DT file. This allows to overlay modifications and keep
clean DT history.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Similar to mount(8) the barebox command mount now supports passing a string
to the file system driver via -o.
This is used in the next commit to let the user specify port numbers for
nfs mounts.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This renames the Freescale and Phytec board directories and defconfig
files to a common naming scheme. The board directories are named
<vendor>-<board> and the defconfig files are named
<vendor>-<board>_defconfig. Also the DataModul realq7 is renamed to its
Marketing Name eDM-QMX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Which bootmode is selected has no longer to be chosen by Kconfig. The
boards can decide themselves which bootmode they want to support. This
makes it unnecesary to ask the user which bootmode shall be supported,
so the "Select boot mode" becomes invisible and both support will be
compiled in as needed by the boards. NAND_IMX_BOOT goes away and the
already existing ARCH_IMX_EXTERNAL_BOOT_NAND can now be used for the
boards to depend on external nand boot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
barebox only recognizes boarddata as dtb if it is inside SDRAM, so
copy the dtb there if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
default_environment_path only exists when CONFIG_ENV_HANDLING is enabled.
Boards would have to #ifdef this if they wanted to use
default_environment_path. Use accessor functions instead which can
be ifdeffed on a single place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The entry function wasn't changed properly when the
prototype changed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The start-r QSB has a different pmic than the older start QSB.
Add a new dts for the QSRB and let barebox generate two images when
LOCO is selected.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Lucas Stach
Sascha Hauer
Christian Hemp
Eric Bénard
Beniamino Galvani
Lucas Stach
Michel Stam
Antony Pavlov
Steffen Trumtrar
Philippe Rétornaz
Uwe Kleine-König
Michael Olbrich
Philipp Zabel
Raphaël POGGI
Sebastian Hesselbarth
Alexander Shiyan