The FSF address has changed; The FSF site says that
address is
Free Software Foundation
51 Franklin Street, Fifth Floor
Boston, MA 02110-1301
USA
(see http://www.fsf.org/about/contact/)
Instead of updating it each time the address changes,
just drop it completely treewide.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We already have an update handler for the MLO on SPI, add
a update handler for the regular barebox aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To make am33xx_uart0_soft_reset more flexible rename it to
am33xx_uart_soft_reset and pass the UART base to it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The static inline wrapper for am33xx_bbu_spi_nor_mlo_register_handler
lacked the 'static inline'. add it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Storing the boot information in the image itself and passing a pointer
around between images is cumbersome and doesn't fit well with multiimage
support where the pointer we pass around is already occupied by the
devicetree.
Do the same as U-Boot does and store the boot information at the bottom
of the SRAM public stack.
To maintain the compatibility between new xloaders and older barebox
binaries we still pass the boot information to the next stage via pointer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a devicetree-only driver for to configure the gpmc and its
child devices from dt. Currently only NAND is supported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces a single omap_init function which detects the
SoC and does all further SoC initialization. This is done to get
rid of initcalls without proper SoC protection. The same has been
done for i.MX already.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The omap3 and omap4/am33xx spi cores differ in the offset of the
registers in the address space. Instead of encoding this into the
resources use the platform_device_id mechanism. This is done in
preparation for devicetree probe support where the address space
is in the devicetree and can't be adjusted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The driver didn't work well with at24 driver. NACKS are lost.
Errors are lost in isr due to the local variable err. Also we didn't wait for
bus free in omap_i2c_xfer_msg.
Fix issues and get other improvements from linux kernel
Tested on OMAP4 and AM335x
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OMAP ROM code passes the boot information via r0 to the
bootloader. Add an OMAP specific barebox handler to pass this
information to the next stage. This allows us to chainload
bootloaders without loosing the information where we booted from.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is a lot of duplicate lowlevel code between the
am33xx boards. Move this code to am33xx_generic and
create structs for sdram settings.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Function should use lower case letters. Also give this function
more namespace. While at it include io.h rather than asm/io.h.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
omap_save_bootinfo derefences the argument passed to barebox without
checking it for validity. This breaks 2nd stage booting where r0
is undefined. The best we can do is to check whether the pointer is
somewhere in SRAM and is word aligned. This at least makes sure that
we do not oops. This introduces SoC specific xxx_save_bootinfo variants
since the SRAM addresses/sizes differ between SoCs.
Additionally fix the prototype for omap_save_bootinfo. It uses r0, so
it must be passed this variable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a omap_set_bootmmc_devname function which can be used
to specify the MMC boot device. In an xload configuration this
is then used to load the next stage. In a regular build this is
used to mount /boot.
Also a device_detect_by_name is added to allow to disable probing
for sd/mmc cards during startup.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-Added mlo spi NOR copy handler
-This handler will convert the MLO to big endian
-Tested with pcm051 board
Signed-off-by: shravan <shravan.k@phytec.in>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The oscillator frequency varies on different AM33xx boards.
Pass the osc frequency from lowlevel board code
to set the correct one on every board.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Reviewed-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
gpiolib user have nothing to define in their machine
specific gpio.h, so do not include it.
The only thing they could define would be ARCH_NR_GPIOS,
but currently no architecture defines it. Should an architecure
feel the need to do it this would be a good opportunity to
get rid of this limitation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The size and offset of the barebox partition in nand and spi nor flash
may vary on different boards. Make it possible to pass this information
over boardfile if needed.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The ROM loader passes the address of a buffer to the MLO in
register 0. Store this data so we can find the boot source later.
On the same way the bootinformation are passed to the barebox,
then. It has to be enshured that r0 contains always the
buffer or the boot source detection will not work.
Applied this on all OMAPs. This patch is based on work of
Jan Luebbe <jlu@pengutronix.de>.
Compile tested on all OMAP boards.
Tested on pcm049, phyCARD-A-L1 and pcm051.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds first stage support for PCM051.
Signed-off-by: Shravan kumar <shravan.k@phytec.in>
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds OMAP machine dependent framebuffer code so that
board files can make use of driver omap-fb.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch removes the call of the cpu_is_* functions completely
and uses id_tables instead.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added device register functions and cpu_is_am33xx()
function.
Adapted the i2c-omap driver. AM335x has a lower
clock rate and the timeout of polling the isr function
had to be increased.
Based on a patch from Shravan Kumar <shravan.k@phytec.in>.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For OMAP4460 omap4_scale_vcores must set the voltage according to mpu freq.
OPP100 700MHz 1210mV
OPPTB 920MHz 1320mV
OPPNT 1200MHz 1380mV
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch includes no functional change. If a configurable DDRPLL_M
is required later, it should be set by the board instead of from here.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The *PLL_N values can be calculated from the OSC value. This patch
includes no functional change.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On OMAP4 SoC there is a SAR memory region (Save & Rescue)
where the ROM code reads the device to boot from.
This patch adds a way to set this.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>