This patch adds support for system controller register driver (SYSCON).
Code taken from Linux Kernel and adapted for using in barebox.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CS6 and CS7 is a internal CPU resources and these chipselects are
already pre configured, so avoid to rewrite this settings.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds helpers to define resources, such as
DEFINE_RES_NAMED, DEFINE_RES_MEM and DEFINE_RES_MEM_NAMED.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for CLPS711X GPIOs. Driver based on
generic GPIO driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds generic memory-mapped GPIO controller support.
Code taken from Linux Kernel and adopted for barebox.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for COMMON_CLK API for CLPS711X targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds clocksource driver for CLPS711X targets and adds
support to platform to use this new driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
__pr_printk is a define which uses a local variable 'ret'. This
means that whenever someone does a pr_*("ret: %d\n", ret);
ret will be 0.
Fix this by writing this without a local variable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes following warning:
drivers/w1/w1.c: In function 'w1_found':
drivers/w1/w1.c:471: warning: integer constant is too large for 'long' type
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes following warning:
drivers/mtd/nand/nand_write.c: In function 'nand_do_write_ops':
drivers/mtd/nand/nand_write.c:272: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows to boot a sequence of boot entries until one succeeds.
boot sources can be passed in $global.boot.default, which is now treated
as a list. Also a list of boot entries can be specified as arguments
to the boot script. The entries can be:
- a plain filename from /env/boot/
- a full path to an arbitrary file
- a directory containing boot entries
With this this command:
boot net nand-ubi /env/boot.d
would first use the /env/boot/net entry, if this fails the /env/boot/nand-ubi
entry and if this also fails the files from /env/boot.d/ (which could also
be links to boot scripts)
To make the above the default, global.boot.default would be specified as:
global.boot.default="net nand-ubi /env/boot.d"
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When the board is booted from NAND we have to setup the iomux to
make the SD card work. Unfortunately this still is not enough :(
The SD card still will only work when booting from it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since recently we check for the page being written for not being
empty and do not actually write it when it is. This fails for a
freshly created flash bad block table when all blocks are good.
In this case the bbt code will try to write an empty page, but
with the BBT marker in OOB. This page never gets written, so the
BBT code will not find a bad block table during next start up and
writes it again. Fix this by checking if we want to write OOB data,
if we do, then write the page, even if the data is empty.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The problem was introduced in
commit 51885a7d73
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Thu Jun 28 09:56:23 2012 +0200
Change byte order detection mechanism to kernel style
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for ext filesystems has been introduced recently. We can now
boot directly from our rootfs, loading the kernel and device tree
images from /boot.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
depending on the power domain register we need to disable sata or mmc
and update the cpu informations
take from Calxeda U-Boot git
Register the original dtb to /dev/firmware-dtb and the fixed dtb to /dev/dtb
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so the board can use it
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The roundup_pow_of_two function is making use of __roundup_pow_of_two
when the call to __builtin_constant_p fails, which is not implemented in
barebox.
Copied the code from Linux log2.h header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we added a new partition in the board, the partitions number of
the boot and rootfs partition have changed as well.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the only storage medium on the cfa-10036 is the MMC card, we need
to have a registered environment partition on it if we want to be able
to modify at runtime.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>