Most i.MX boards can use the imx*_barebox_entry functions. The remaining
(i.MX21, i.MX6) use hardcoded base addresses.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Efika MX Smartbook is a i.MX51 based netbook. This patch adds
nearly full support for it including:
- USB
- SD card slots
- Internal SPI NOR flash
- Internal flash PATA drive
- LEDs
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch provides a global cleanup barebox Kconfig files. This includes
replacing spaces to tabs, formatting in accordance format, removing
extraneous lines and spaces. No functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the Garz+Fricke Vincell board. This has
a i.MX53 Processor with 512MB of DDR3 RAM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Update help info, it's slightly out of date, and a grammatical fix.
No functional change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old clock support is now unused. Remove it. The former i.MX clko
command is superseeded by generic clock manipulation commands.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for ConnectCore® i.MX51 board from Digi International.
A separate option includes support for debugging board for this module.
Some code taken from the bootloader U-Boot and patch from Digi.
Functional of Ethernet not tested yet.
barebox 2012.05.0-00316-g4024d9c-dirty #0 Wed Jun 6 13:08:25 MSK 2012
Board: ConnectCore i.MX51
Module Variant: i.MX515@600MHz, PHY, Acceleromter (0x0b)
Module HW Rev : 02
Module Serial : B111156789
mc13xxx-spi@mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: Bad block at 0x00ce0000
nand_read_bbt: Bad block at 0x05bc0000
nand_read_bbt: Bad block at 0x0bc40000
ehci@ehci0: USB EHCI 1.00
detected i.MX51 rev 3.0
imx-esdhc@mci0: registered as mci0
imx-esdhc@mci1: registered as mci1
Malloc space: 0x95f00000 -> 0x97efffff (size 32 MB)
Stack space : 0x95ef8000 -> 0x95f00000 (size 32 kB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
Hit any key to stop autoboot: 3
barebox@ConnectCore i.MX51:/
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the pcm038 board to the new environment template and
does the necessary defaultconfig adjustments. Additionally it disables
UBI support as the pcm038 image is getting bigger and bigger and UBI
seems to be the most unused big (in size) feature.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some devices need to be moved to the PCM970 source file later, because
in fact these devices are not installed on the main unit PCM038.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Supported devices:
- nand
- ethernet
- mmc0, mmc1 (on stk5v3 development board)
- led (on stk5v3 development board)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also renamed config option name to MFD_MC13XXX.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added num_modes to all imx_ipu_fb_platform_data structs.
Removed defines for pcm043 to choose display.
We may switch this during runtime now.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The lowlevel init function was a 1:1 copy from the babbage
baord, so it should be safe to switch to the generic C
lowlevel init.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Eric Benard <eric@eukrea.com>
This adds additional Kconfig help to clarify the way to use barebox
for eFuses handling.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not depend on the specific SoCs for the IIM module, but
instead exclude the one that don't have this unit.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX Processors support two different boot modes, the internal
boot mode and the external boot mode. Traditionally the external
NAND boot mode is handled in drivers/mtd/nand and the internal
boot mode is handled in arch/arm/mach-imx. This patch consolidates
the handling of both boot modes in arch/arm/mach-imx so that
the user does not have to look in the mtd kconfig section for
booting from NAND. Also, selecting between internal and external
boot mode now is a clear choice.
The external NAND boot mode has been independent of the mtd nand
driver, but as the code was contained in the NAND driver it was
not possible to support booting from NAND without a mtd nand driver.
This is changed with this patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without this patch (against next) I get this:
rsc@thebe:barebox$ make ARCH=arm CROSS_COMPILE=<path>/arm-v5te-linux-gnueabi- menuconfig
HOSTCC scripts/kconfig/lxdialog/checklist.o
HOSTCC scripts/kconfig/lxdialog/inputbox.o
HOSTCC scripts/kconfig/lxdialog/menubox.o
HOSTCC scripts/kconfig/lxdialog/textbox.o
HOSTCC scripts/kconfig/lxdialog/util.o
HOSTCC scripts/kconfig/lxdialog/yesno.o
HOSTCC scripts/kconfig/mconf.o
HOSTLD scripts/kconfig/mconf
scripts/kconfig/mconf Kconfig
warning: (ARCH_IMX25 && ARCH_IMX27 && ARCH_IMX35 && ARCH_IMX51 && ARCH_IMX28) selects ARCH_HAS_FEC_IMX which has unmet direct dependencies (ARCH_IMX)
warning: (ARCH_IMX25 && ARCH_IMX27 && ARCH_IMX35 && ARCH_IMX51 && ARCH_IMX28) selects ARCH_HAS_FEC_IMX which has unmet direct dependencies (ARCH_IMX)
Add the option for the FEC on MX28 as well.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
