This driver should work with some Atheros WiSoCs:
- ar2312, ar2313
- ar2315, ar2316 ...
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX53 fec claims to be compatible to i.MX25 and i.MX53. In barebox
we do not have to make differences between i.MX25 and i.MX27 though, so
just fall back to i.MX27.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The core has a bit for swapping packet data endianism.
Reset default from Cadence is off. Xilinx however, that uses this core on the
Zynq SoCs, opted for on. Turn it off for all devices.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The macb/gem core is used by the Zynq SoC. In preparation of sharing
the macb driver between at91 and Zynq, rename the platform data to
'struct macb_platform_data', and move the definition to a common
location.
Signed-off-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we use a full buffer no need to check the SOF
and reset the rx_tail
fix at the same time the gem detection so we can have the rx_buffer
allocated correctly according to the IP
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
do not try to read the status in force mode
the link is up
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Due to a hw bug do not enable teh Asym_Pause.
Otherwise if you ser the bit 11 in 4h you will have to unplug
and replug the cable to make the phy work.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
based on the kernel code
detect it via IP version
In the GEM we can use a full packet buffer for receive but the buffer size
need to be 64bit size aligned.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the mininal tx ring size is 2 as if one we wrap on the same descriptor
and can cause IP lock on GEM (gigabit version) this is always the case
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as eth_device init is planning for remove and we need the init before register
the mdio bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we will add later the GMAC IP verion support (GEM)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When starting a network device wait until the link is up. Otherwise
autobooting does not work with little timeout and several attempts
have to be made until the network is finally up.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
dev_add_child is a very unsafe function. If called multiple times
it allows setting the same device to different parents thus corrupting
the siblings list. This happens regularly since:
| commit c2e568d19c
| Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| Date: Sat Nov 3 16:11:05 2012 +0100
|
| bus: add bus device
|
| automatically add it as parent of any bus device if none already specified
|
| we have now a nice output per bus
If for example a FATfs is mounted this nice output per bus often ends with:
> `---- fat0
> `---- 0
> `---- 0x86f0000087020031-0x86f000410df27124: /dev/<NULL>
> `---- sram00
> `---- 0x00000000-0xffffffffffffffff: /dev/<NULL>
> `---- 0x00000000-0xffffffffffffffff: /dev/<NULL>
> unable to handle NULL pointer dereference at address 0x0000000c
> pc : [<87f08a20>] lr : [<87f08a04>]
> sp : 86eff8c0 ip : 87f3fbde fp : ffffffff
> r10: ffffffff r9 : 00000000 r8 : 00000003
> r7 : 86f075b8 r6 : 00000002 r5 : ffffffec r4 : 86f07544
> r3 : 00000000 r2 : 43f900b4 r1 : 00000020 r0 : 00000005
> Flags: Nzcv IRQs off FIQs off Mode SVC_32
> [<87f08a20>] (do_devinfo_subtree+0x90/0x130) from [<87f08a90>] (do_devinfo_subtree+0x100/0x130)
>
> [<87f3e070>] (unwind_backtrace+0x0/0x90) from [<87f28514>] (panic+0x28/0x3c)
> [<87f28514>] (panic+0x28/0x3c) from [<87f3e4b8>] (do_exception+0x10/0x14)
> [<87f3e4b8>] (do_exception+0x10/0x14) from [<87f3e544>] (do_data_abort+0x2c/0x38)
> [<87f3e544>] (do_data_abort+0x2c/0x38) from [<87f3e268>] (data_abort+0x48/0x60)
This patch fixes this by adding a device to its parents children list in
register_device so that dev_add_child is no longer needed. This function
is removed from the tree. Now callers of register_device have to clearly
set the parent *before* registering a device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Jan Lübbe <jlu@pengutronix.de>
Some phys come up with this bit set, clear it so that these phys
can work. This has been observed with a ASIX compatible USB ethernet
adapter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch provides a global cleanup barebox Kconfig files. This includes
replacing spaces to tabs, formatting in accordance format, removing
extraneous lines and spaces. No functional changes.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on barebox we have the weird way the return 0 true on bus match
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
if board need specific phy fixup they can register it and then the code will
executed only if needed
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
on barebox we have the weird way the return 0 true on bus match
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the generic phy driver is used if no driver are found
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as in the kernel use is_rmii
flags for pinctrl
phy_flags for phylib flags
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While this makes sure that the phy fixups are applied even if
networking is not used on i.MX6, this patch due to latest phy
changes causes the startup of barebox delayed until we have a
link on the i.MX fec. Revert it for now and look for a better
solution later.
This reverts commit 3a17af33c0.
as we to have specific phy init to fix chip issue link detection support
based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to allow to register an array of drivers
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On LAN9115/LAN9117/LAN9215/LAN9217, external PHYs are supported.
Switch to external PHY based on hardware strap pin and/or override flags.
Also add a mask to platform data selecting external PHY address to be used.
Code based on linux/drivers/net/ethernet/smsc/smsc911x.c (fd9abb3d, d23f028a).
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
commit 89dfe2d2af "mdiobus: do not scan
the bus at registration time" dropped the check for struct mii_bus
element phy_mask while scanning through all addresses.
Re-add this check.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Scanning the bus can take some time. If we do not need the ethernet
device, this is unnecessary, so delay the scan until the phy device
iactually is needed.
Andread Pretzsch: Fixup bug in scanning for all devices.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
fec_init() initializes some bits important for phy access, so do
this before the mdiobus is registered. This fixes mdiobus support
on i.MX28 boards in RMII mode.
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Test if we already found a phy device on an address earlier and return
it if it exists. This makes it possible to call mdiobus_scan multiple
times.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several i.MX boards (all i.MX6 boards) need to do some adjustments
to phy registers. If barebox itself does not use network, networking
won't work in the kernel if the kernel does not have the fixups. Connect
the phy at probe time so that these tweaks are done during probe so that
the kernel works without phy register tweaks. Also this has the effect
that the phy device is present and introspectable without doing fake
network transfers beforehand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If none set use NA (0) as before.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On i.MX we enable all necessary clocks during startup of the clock
controller driver, so we do not need the register hacking in the drivers
anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The _send function should not return the length
of the transmitted packet.
See also
commit 76c4c9e48f
Author: Jan Luebbe <jlu@pengutronix.de>
Date: Fri Sep 28 18:17:44 2012 +0200
davinci_emac: return 0 on successful transmit
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the device id mechanism to the i.MX fec driver and
uses it to determine the fec version. Also adds devicetree
probing support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_update_linkspeed':
/opt/work/barebox/drivers/net/designware.c:234:9: error: 'mac_p' undeclared (first use in this function)
/opt/work/barebox/drivers/net/designware.c:234:9: note: each undeclared identifier is reported only once for each function it appears in
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_ether_open':
/opt/work/barebox/drivers/net/designware.c:254:6: error: too few arguments to function 'phy_device_connect'
/opt/work/barebox/include/linux/phy.h:252:5: note: declared here
/opt/work/barebox/drivers/net/designware.c: At top level:
/opt/work/barebox/drivers/net/designware.c:226:13: warning: 'dwc_update_linkspeed' defined but not used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can check it with the kernel one
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also pass flags using platform_data and remove useless casts from void*.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The _send function should not return the length of the transmitted packet.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Adapt phylib from linux
switch all the driver to it
reimplement mii bus
This will allow to have
- phy drivers
- to only connect the phy at then opening of the device
- if the phy is not ready or not up fail on open
Same behaviour as in linux and will allow to share code and simplify porting.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
this will ensure the data are set to 0 (list as example)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It starts the switch and provides basic access to the registers.
This driver could also work with some other Micrel switches, possibly
with some small changes.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
since 99e72c8bbd on an i.MX51 based board,
I get : "phy0: Link is up - 1000/Full". It seems miidev tries to probe
the PHY to early and gets 0x3ffff which leads to the wrong capabilities
setting.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If pdata is NULL smc911x_probe will crash. Checking the zero initialized
priv->shift results in default configuration if pdata is not set.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the check need to be inverted
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
poll the READY bit in PMT_CTRL. Any other access to the device is
forbidden while this bit isn't set. Try for 100ms
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use linux kernel chip detection from 3.5
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
detect if the bus is swapped and report a 32bit drivers is used on a 16bit bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
switch ipe337: to it at the same time to do not brake it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to replace them depending on the platform data.
So we can specify shift and reg io witdh (16bit/32bit)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this make the driver more readable
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
miidev_wait_aneg() polled the wrong bit, so link detection did fail on
boards where the PHY had to come out of a powerdown mode.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This update adds the GIANFAR driver along with the configuration
and build files.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The dump generated by "md -w -s /dev/phy0"
suggests individual registers need to be
addressed by byte offset, not by register number.
E.g. to set the autonegotiation advertisement register
for 10Mbit only, use "mw -w -d /dev/phy0 8+2 0x0061".
The current mix of offset == register number, but
count == byte count is unintuitive.
Also, to be consistent with "md" on /dev/mem, round up
the count so "8+1" also works to access one register.
However, no attempt is made to do read-modify-write
single byte writes.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Check if the PHY is really accessible (e.g. the
PHY address is correct) during probe.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The auto negotiation result is the intersect
of the advertised abilities and the link partner abilities.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Straight forward port of Synopsys Designware ethernet
driver from u-boot v2012.04.01.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If DEBUG is defined it fails due to wrong variable names
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some phys need board specific fixups. To be able to do this
from board code add mii_open/mii_close functions so that the
board can use the regular mii_read/mii_write functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently only 100Mb/s is tested. Freescale's U-Boot suggests that
there are some additional adjustments necessary for Gigabit support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wait until the reset bit is actually cleared instead of some
arbitrary delay (which caused problems with a PHY which was in some
energy saving mode).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
First check the status at least once, then do timeout checks. Minor
cleanups also.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for KS8851 16bit MLL chip from Micrel Inc.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will ensure that we send an other packet only when the first one is send.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
First call mii_unregister which is done in the drivers unbind function,
then eth_unregister. Also, remove unregister_device which is done in
eth_unregister.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>