The beaglebone white and black have different devicetrees. Both
get linked into the MLO which makes it too big. Use a devicetree
generated from am335x-bone-common.dtsi which both board variants
can share. This reduces the binary size by about 30k.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Mainly for Jetson TK1 support, but -next moved
some stuff around. Also enable some filesystems.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We can reuse the Tegra30 pinctrl driver, as the bit
layout is the same. Just add the pin and drivegroups
and some compile-time magic to avoid bloat.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If the bootloader doesn't init the architectural timer
on Cortex A15 Linux falls over when trying to boot.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I don't know why get_runtime_offset fails on T124 yet,
but this is a safe workaround, with the nice side-effect
of fixing second stage barebox loading.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Don't disable clk to unrelated devices in the process.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Those 3 are needed to power CPU0 from the CPUG cluster.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Even the lowlevel functions are growing to a
size where having a stack seem beneficial.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In RCM aka recovery mode the BootROM waits for a
usbloader to take over control. On most boards this
is triggered by holding a physical switch which may
be inconvinient at times. Add a command to switch
into RCM from software.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It wasn't hard to find the right spot to copy the image
to before, but this makes it a bit more explicit.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The voltage for programming the fuses is external to the SoC and
on some boards this is controllable with a regulator, so add regulator
support to the iim driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Allow to read/write the registered MAC addresses in the iim
module directly via a device parameter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX5 iim has an additional bit in the CCM module which
enables the supply. Add support for it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx_iim_read is a iim internal function, so access the
internal functions rather than using the cdev API.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With devicetree devicenames start with numbers. Parameters on these
devices are not accessible since variables can't start with numbers.
Register a logical 'iim' device which makes the permanent_write_enable
and explicit_sense_enable parameters accessible again.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of duplicating data shared between the banks in a bank
specific struct, use a iim struct and a bank struct.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* fix indentation of options in 'help bootm'
* add missing help for -m
* put some output into debug/verbose mode
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Alexander Shiyan
Sascha Hauer
Lucas Stach
Lucas Stach
Bo Shen
Holger Schurig