Update help info, it's slightly out of date, and a grammatical fix.
No functional change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch sets HPM (Host power mask bit) to bit 16 according to i.MX
Reference Manual. Falsely it was set to bit 8, but this controls pull-up
Impedance.
Reported-by: Michael Burkey <mdburkey@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The same issue was fixed in the Linux kernel in commit
66ddfc6 (mx35: add a missing comma in a pad definition)
for 2.6.33-rc7.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for an update handler for internal boot. Currently
handled are:
- v1 MMC/SD
- v2 MMC/SD
- v2 NAND
where v1 is found on i.MX25, i.MX35 and i.MX51. v2 is found on i.MX53.
This code intentionally does not use the DCD data compiled into every
i.MX internal boot image. This makes it possible to make a pure second
stage barebox bootable on i.MX internal boot devices later.
This has been tested on the i.MX51 babbage, i.MX53 loco and i.MX53 tx53
board.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The KARO Tx53 board in the revision 8030 has an instable SDRAM
setup. It works as long as the MMU is disabled, but the board
crashes at arbitrary places once the MMU gets enabled. So we
need the PLL setup early. Enable it for pbl.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This redefines the sdram controller registers as offsets to the base
rather than as absolute addresses. All users are fixed to use the
SoC specific base address.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rather than doing this in the SoC specific code just print
it in imx_set_silicon_revision. This saves some lines of code
and also results in i.MX27 now also having the silicon revision
printed during startup.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This moves the known i.MX bootsource settings to a single file
so that the code can be shared. Also we add a enum for the different
boot sources so that it can be used in C Code and not only on the shell.
The pcm038 board is changed to use it instead of digging in the registers
manually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On i.MX we enable all necessary clocks during startup of the clock
controller driver, so we do not need the register hacking in the drivers
anymore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- for i.MX1 the register is in the System Control unit, so move
the code to arch/arm/mach-imx/imx1.c
- for the other i.MX the register is in the watchdog unit, so move
the code to drivers/watchdog/imxwd.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
of_alias_get_id() returns the number of the gpio bank, so we have
to multiply with 32 to get the gpio base.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- Add a separate header file for the iomux-v1 just like done for
iomux-v3.
- initialize iomux from SoC code so that we do not depend on IMX_GPIO_BASE
anymore.
- define registers as offset to the base rather than absolute addresses
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All i.MX SoCs now use the same imx_silicon_revision() function to get
the revision. Add a separate header file for it and a common function
used on all SoCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the device id mechanism to the i.MX fec driver and
uses it to determine the fec version. Also adds devicetree
probing support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Robert P. J. Day
Christoph Fritz
Sascha Hauer
Uwe Kleine-König